Performance study of multirate circuit switching in quantized clos network.

by Vincent Wing-Shing Tse.Thesis submitted in: December 1997.Thesis (M.Phil.)--Chinese University of Hong Kong, 1998.Includes bibliographical references (leaves 62-[64]).Abstract also in Chinese.Chapter 1 --- Introduction --- p.1Chapter 2 --- Principles of Multirate Circuit Switching in Quantized Clos Network --- p.10Chapter 2.1 --- Formulation of Multirate Circuit Switching --- p.11Chapter 2.2 --- Call Level Routing in Quantized Clos Network --- p.12Chapter 2.3 --- Cell Level Routing in Quantized Clos Network --- p.16Chapter 2.3.1 --- Traffic Behavior in ATM Network --- p.17Chapter 2.3.2 --- Time Division Multiplexing in Multirate Circuit Switching and Cell-level Switching in ATM Network --- p.19Chapter 2.3.3 --- Cell Transmission Scheduling --- p.20Chapter 2.3.4 --- Capacity Allocation and Route Assignment at Cell-level --- p.29Chapter 3 --- Performance Evaluation of Different Implementation Schemes --- p.31Chapter 3.1 --- Global Control and Distributed Switching --- p.32Chapter 3.2 --- Implementation Schemes of Quantized Clos Network --- p.33Chapter 3.2.1 --- Classification of Switch Modules --- p.33Chapter 3.2.2 --- Bufferless Switch Modules Construction Scheme --- p.38Chapter 3.2.3 --- Buffered Switch Modules Construction Scheme --- p.42Chapter 3.3 --- Complexity Comparison --- p.44Chapter 3.4 --- Delay Performance of The Two Implementation Schemes --- p.47Chapter 3.4.1 --- Assumption --- p.47Chapter 3.4.2 --- Simulation Result --- p.50Chapter 4 --- Conclusions --- p.59Bibliography --- p.6

Design techniques to enhance low-power wireless communication soc with reconfigurability and wake up radio

Nowadays, Internet of things applications are increasing, and each end-node has more demanding requirements such as energy efficiency and speed. The thesis proposes a heterogeneous elaboration unit for smart power applications, that consists of an ultra-low-power microcontroller coupled with a small (around 1k equivalent gates) soft-core of embedded FPGA. This digital system is implemented in 90-nm BCD technology of STMicroelectronics, and through the analysis presented in this thesis proves to have good performance in terms of power consumption and latency. The idea is to increase the system performance exploiting the embedded FPGA to managing smart power tasks. For the intended applications, a remarkable computational load is not required, it is just required the implementation of simple finite state machines, since they are event-driven applications. In this way, while the microcontroller deals with other system computations such as high-level communications, the eFPGA can efficiently manage smart power applications. An added value of the proposed elaboration unit is that a soft-core approach is applied to the whole digital system including the eFPGA, and hence, it is portable to different technologies. On the other hand, the configurability improvement has a straightforward drawback of about a 20–27% area overhead. The eFPGA usage to manage smart power applications, allows the system to reduce the required energy per task from about 400 to around 800 times compared to a processor implementation. The eFPGA utilization improves also the latency performance of the system reaching from 8 to 145 times less latency in terms of clock cycles. The thesis also introduces the architecture of a nano-watt wake-up radio integrated circuit implemented in 90-nm BCD technology of STMicroelectronics. The wake-up radio is an auxiliary always-on radio for medium-range applications that allows the IoT end-nodes to drastically reduce the power consumption during the node idle-listening communication phase

Journal of Telecommunications and Information Technology, 2018, nr 1

kwartalni

Switching techniques for broadband ISDN

The properties of switching techniques suitable for use in broadband networks have been investigated. Methods for evaluating the performance of such switches have been reviewed. A notation has been introduced to describe a class of binary self-routing networks. Hence a technique has been developed for determining the nature of the equivalence between two networks drawn from this class. The necessary and sufficient condition for two packets not to collide in a binary self-routing network has been obtained. This has been used to prove the non-blocking property of the Batcher-banyan switch. A condition for a three-stage network with channel grouping and link speed-up to be nonblocking has been obtained, of which previous conditions are special cases. A new three-stage switch architecture has been proposed, based upon a novel cell-level algorithm for path allocation in the intermediate stage of the switch. The algorithm is suited to hardware implementation using parallelism to achieve a very short execution time. An array of processors is required to implement the algorithm The processor has been shown to be of simple design. It must be initialised with a count representing the number of cells requesting a given output module. A fast method has been described for performing the request counting using a non-blocking binary self-routing network. Hardware is also required to forward routing tags from the processors to the appropriate data cells, when they have been allocated a path through the intermediate stage. A method of distributing these routing tags by means of a non-blocking copy network has been presented. The performance of the new path allocation algorithm has been determined by simulation. The rate of cell loss can increase substantially in a three-stage switch when the output modules are non-uniformly loaded. It has been shown that the appropriate use of channel grouping in the intermediate stage of the switch can reduce the effect of non-uniform loading on performance

Novel techniques in large scaleable ATM switches

Bibliography: p. 172-178.This dissertation explores the research area of large scale ATM switches. The requirements for an ATM switch are determined by overviewing the ATM network architecture. These requirements lead to the discussion of an abstract ATM switch which illustrates the components of an ATM switch that automatically scale with increasing switch size (the Input Modules and Output Modules) and those that do not (the Connection Admission Control and Switch Management systems as well as the Cell Switch Fabric). An architecture is suggested which may result in a scalable Switch Management and Connection Admission Control function. However, the main thrust of the dissertation is confined to the cell switch fabric. The fundamental mathematical limits of ATM switches and buffer placement is presented next emphasising the desirability of output buffering. This is followed by an overview of the possible routing strategies in a multi-stage interconnection network. A variety of space division switches are then considered which leads to a discussion of the hypercube fabric, (a novel switching technique). The hypercube fabric achieves good performance with an O(N.log₂N)²) scaling. The output module, resequencing, cell scheduling and output buffering technique is presented leading to a complete description of the proposed ATM switch. Various traffic models are used to quantify the switch's performance. These include a simple exponential inter-arrival time model, a locality of reference model and a self-similar, bursty, multiplexed Variable Bit Rate (VBR) model. FIFO queueing is simple to implement in an ATNI switch, however, more responsive queueing strategies can result in an improved performance. An associative memory is presented which allows the separate queues in the ATM switch to be effectively logically combined into a single FIFO queue. The associative memory is described in detail and its feasibility is shown by laying out the Integrated Circuit masks and performing an analogue simulation of the IC's performance is SPICE3. Although optimisations were required to the original design, the feasibility of the approach is shown with a 15Ƞs write time and a 160Ƞs read time for a 32 row, 8 priority bit, 10 routing bit version of the memory. This is achieved with 2µm technology, more advanced technologies may result in even better performance. The various traffic models and switch models are simulated in a number of runs. This shows the performance of the hypercube which outperforms a Clos network of equivalent technology and approaches the performance of an ideal reference fabric. The associative memory leverages a significant performance advantage in the hypercube network and a modest advantage in the Clos network. The performance of the switches is shown to degrade with increasing traffic density, increasing locality of reference, increasing variance in the cell rate and increasing burst length. Interestingly, the fabrics show no real degradation in response to increasing self similarity in the fabric. Lastly, the appendices present suggestions on how redundancy, reliability and multicasting can be achieved in the hypercube fabric. An overview of integrated circuits is provided. A brief description of commercial ATM switching products is given. Lastly, a road map to the simulation code is provided in the form of descriptions of the functionality found in all of the files within the source tree. This is intended to provide the starting ground for anyone wishing to modify or extend the simulation system developed for this thesis