Fastening the Initial Access in 5G NR Sidelink for 6G V2X Networks

The ever-increasing demand for intelligent, automated, and connected mobility solutions pushes for the development of an innovative sixth Generation (6G) of cellular networks. A radical transformation on the physical layer of vehicular communications is planned, with a paradigm shift towards beam-based millimeter Waves or sub-Terahertz communications, which require precise beam pointing for guaranteeing the communication link, especially in high mobility. A key design aspect is a fast and proactive Initial Access (IA) algorithm to select the optimal beam to be used. In this work, we investigate alternative IA techniques to fasten the current fifth-generation (5G) standard, targeting an efficient 6G design. First, we discuss cooperative position-based schemes that rely on the position information. Then, motivated by the intuition of a non-uniform distribution of the communication directions due to road topology constraints, we design two Probabilistic Codebook (PCB) techniques of prioritized beams. In the first one, the PCBs are built leveraging past collected traffic information, while in the second one, we use the Hough Transform over the digital map to extract dominant road directions. We also show that the information coming from the angular probability distribution allows designing non-uniform codebook quantization, reducing the degradation of the performances compared to uniform one. Numerical simulation on realistic scenarios shows that PCBs-based beam selection outperforms the 5G standard in terms of the number of IA trials, with a performance comparable to position-based methods, without requiring the signaling of sensitive information

Mobile Ad-Hoc Networks

Being infrastructure-less and without central administration control, wireless ad-hoc networking is playing a more and more important role in extending the coverage of traditional wireless infrastructure (cellular networks, wireless LAN, etc). This book includes state-of the-art techniques and solutions for wireless ad-hoc networks. It focuses on the following topics in ad-hoc networks: vehicular ad-hoc networks, security and caching, TCP in ad-hoc networks and emerging applications. It is targeted to provide network engineers and researchers with design guidelines for large scale wireless ad hoc networks

Facilitating Internet of Things on the Edge

The evolution of electronics and wireless technologies has entered a new era, the Internet of Things (IoT). Presently, IoT technologies influence the global market, bringing benefits in many areas, including healthcare, manufacturing, transportation, and entertainment. Modern IoT devices serve as a thin client with data processing performed in a remote computing node, such as a cloud server or a mobile edge compute unit. These computing units own significant resources that allow prompt data processing. The user experience for such an approach relies drastically on the availability and quality of the internet connection. In this case, if the internet connection is unavailable, the resulting operations of IoT applications can be completely disrupted. It is worth noting that emerging IoT applications are even more throughput demanding and latency-sensitive which makes communication networks a practical bottleneck for the service provisioning. This thesis aims to eliminate the limitations of wireless access, via the improvement of connectivity and throughput between the devices on the edge, as well as their network identification, which is fundamentally important for IoT service management. The introduction begins with a discussion on the emerging IoT applications and their demands. Subsequent chapters introduce scenarios of interest, describe the proposed solutions and provide selected performance evaluation results. Specifically, we start with research on the use of degraded memory chips for network identification of IoT devices as an alternative to conventional methods, such as IMEI; these methods are not vulnerable to tampering and cloning. Further, we introduce our contributions for improving connectivity and throughput among IoT devices on the edge in a case where the mobile network infrastructure is limited or totally unavailable. Finally, we conclude the introduction with a summary of the results achieved

Conception et réalisation d'un nouveau transpondeur DSRC à faible consommation

To increase the efficiency and safety of the road traffic, new concepts and technologies have been developed in Europe since 1992 for RTTT applications (Road Traffic & Transport Telematics). These applications use the Dedicated Short Range Communications (DSRC) devices at 5.8 GHz (ISM band). In view of the reliability and success of this technology, the use of such equipment is thus extended to the EFC (Electronic Fee Collection) or e-toll and also in many other application areas such as fleet management, public transport and parking management. Due to the broad applications, these equipments are subject to various standards CEN/TC 278, CEN ENV (EN) 12253, ETSI, etc.... The DSRC system consists in a transceiver (reader) and transponders (tags). Industrial approaches are oriented to semi-passive transponder technology, which uses the same signal sent by the reader to retransmit, performing a frequency shift and encoding data to be transmitted. This design avoids the use of the local oscillators to generate the RF wave, as in active transponders, and save electrical energy of batteries. This allows the development of relatively low cost and small size transponders. Despite advances in integrated low-power circuits technology, this concept still requires a lithium battery to operate the transponder for a period of 4-6 years. However, with the expansion of these facilities, it appears that over the years the amount of lithium to destroy has become a crucial problem for the environment. Nowadays designing a completely autonomous DSRC transponder is not feasible, since the amount of energy required is still high (8 mA/3.6 V active mode). Nevertheless, reducing the transponder electrical power consumption, as a solution to at least double the battery life, could be a good start point to improve environment protection.In this thesis we propose a new DSRC transponder with an original statechart that considerably reduces the power consumption. After validation of the new low-power consumption mode, we studied the possibility to recharge the battery of the transponder by means of Wireless Energy Harvesting. The DSRC Toll Collection RF link budget was carried out in order to estimate the amount of energy available when a car with a transponder passes through a toll system. However, RF link budget at 5.8 GHz presents a low power density, since the car does not stay enough on the DSRC antenna's field to proceed to energy harvesting. Therefore we explored another ISM frequency, the 2.45 GHz. Thus the Wireless Energy Harvesting chapter aims to further the state of the art through the design and optimization of a novel RF harvesting board design. We demonstrated that an optimum RF-DC load is required in order to achieve high RF-DC conversion efficiency. Several rectifiers and rectennas were prototyped in order to validate the numerical studies. Finally, the results obtained in this thesis are in the forefront of the State-of-the-Art of Wireless Energy Harvesting for very low available power density.Afin d'augmenter l'efficacité et la sécurité du trafic routier, de nouveaux concepts et technologies ont été développés depuis 1992 en Europe pour les applications RTTT (Road Traffic & Transport Telematics). Ces applications utilisent les équipements DSRC qui supportent les transmissions à courte distance à 5.8GHz. Vues la fiabilité et le succès de cette technologie, l'utilisation de ces équipements est ensuite étendue aux ETC (Electronic Toll Collection) ou Télépéage et aussi dans une multitude d'autres domaines d'application comme la gestion des flottes, le transport public et la gestion des parkings. Le système DSRC se compose d'un émetteur/récepteur (lecteur) et des transpondeurs (badges). En toute logique, l'approche industrielle oriente les développements vers la technologie de transpondeur semi passif qui, pour réémettre un signal utilise le signal transmis par l'émetteur–récepteur, effectue une modulation de phase d'une sous porteuse fréquentielle encodant ainsi les données à transmettre. Cette conception évite l'utilisation des oscillateurs locaux, comme dans les transpondeurs actifs, pour générer l'onde Radio Fréquence (RF). Ceci permet de produire des transpondeurs relativement à faible coût et de petite taille. Cependant ce concept nécessite quand même une batterie au Lithium pour assurer le fonctionnement du transpondeur pour une durée de 4 à 6 ans et ce malgré les progrès des technologies de circuits intégrés à faible consommation. Au fur et à mesure de l'expansion de ces équipements, il s'avère qu'avec les années la quantité des batteries au lithium à détruire deviendrait un problème crucial pour l'environnement. Aujourd'hui, la conception d'un transpondeur DSRC complètement autonome n'est pas faisable, car la quantité d'énergie nécessaire s'avère encore élevée (mode actif 8 mA/3.6 V). Néanmoins, la réduction de la consommation électrique du transpondeur, permet au moins doubler la durée de vie de la batterie et pourrait être un bon point de départ pour améliorer la protection de l'environnement.Dans cette thèse, nous proposons un nouveau transpondeur DSRC avec un diagramme d'état original qui réduit considérablement la consommation énergétique. Après validation d'un nouvel état de fonctionnement en mode très faible consommation d'énergie, nous avons étudié la possibilité de recharger la batterie du transpondeur à travers de la récupération d'énergie sans fil. Le bilan de liaison énergétique DSRC a été réalisé afin d'estimer la quantité d'énergie disponible quand une voiture avec un transpondeur passe à sous un système de péage. Toutefois, le bilan énergétique à 5.8 GHz présente une faible densité d'énergie RF, puisque la voiture ne reste pas assez sur le lobe de l'antenne DSRC afin de procéder à la récupération d'énergie. Par conséquent, nous avons alors exploré une autre fréquence ISM, le 2.45 GHz dans laquelle la présence d'émetteurs est bien plus grande. Dans le chapitre de récupération d'énergie sans fil nous présentons la conception et l'optimisation d'un nouveau récupérateur d'énergie RF. Après avoir démontré qu'une charge RF-DC optimale est nécessaire afin d'atteindre une haute efficacité de conversion RF-DC. Plusieurs redresseurs et rectennas ont été conçus pour valider les études numériques. Parmi, les résultats présentés dans cette thèse les rendement de conversion obtenus sont à l'état de l'art de la récupération d'énergie sans fil pour une très faible densité de puissance disponible

Unmanned Aerial Vehicle (UAV)-Enabled Wireless Communications and Networking

The emerging massive density of human-held and machine-type nodes implies larger traffic deviatiolns in the future than we are facing today. In the future, the network will be characterized by a high degree of flexibility, allowing it to adapt smoothly, autonomously, and efficiently to the quickly changing traffic demands both in time and space. This flexibility cannot be achieved when the network’s infrastructure remains static. To this end, the topic of UAVs (unmanned aerial vehicles) have enabled wireless communications, and networking has received increased attention. As mentioned above, the network must serve a massive density of nodes that can be either human-held (user devices) or machine-type nodes (sensors). If we wish to properly serve these nodes and optimize their data, a proper wireless connection is fundamental. This can be achieved by using UAV-enabled communication and networks. This Special Issue addresses the many existing issues that still exist to allow UAV-enabled wireless communications and networking to be properly rolled out