Ground Profile Recovery from Aerial 3D LiDAR-based Maps

The paper presents the study and implementation of the ground detection methodology with filtration and removal of forest points from LiDAR-based 3D point cloud using the Cloth Simulation Filtering (CSF) algorithm. The methodology allows to recover a terrestrial relief and create a landscape map of a forestry region. As the proof-of-concept, we provided the outdoor flight experiment, launching a hexacopter under a mixed forestry region with sharp ground changes nearby Innopolis city (Russia), which demonstrated the encouraging results for both ground detection and methodology robustness.Comment: 8 pages, FRUCT-2019 conferenc

Optimal Constrained Wireless Emergency Network Antennae Placement

With increasing number of mobile devices, newly introduced smart devices, and the Internet of things (IoT) sensors, the current microwave frequency spectrum is getting rapidly congested. The obvious solution to this frequency spectrum congestion is to use millimeter wave spectrum ranging from 6 GHz to 300 GHz. With the use of millimeter waves, we can enjoy very high communication speeds and very low latency. But, this technology also introduces some challenges that we hardly faced before. The most important one among these challenges is the Line of Sight (LOS) requirement. In the emergent concept of smart cities, the wireless emergency network is set to use millimeter waves. We have worked on the problem of efficiently finding a line of sight for such wireless emergency network antennae in minimal time. We devised two algorithms, Sequential Line of Sight (SLOS) and Tiled Line of Sight (TLOS), both perform better than traditional algorithms in terms of execution time. The tiled line of sight algorithm reduces the time required for a single line of sight query from 200 ms for traditional algorithms to mere 1.7 ms on average

3D oceanographic data compression using 3D-ODETLAP

This paper describes a 3D environmental data compression technique for oceanographic datasets. With proper point selection, our method approximates uncompressed marine data using an over-determined system of linear equations based on, but essentially different from, the Laplacian partial differential equation. Then this approximation is refined via an error metric. These two steps work alternatively until a predefined satisfying approximation is found. Using several different datasets and metrics, we demonstrate that our method has an excellent compression ratio. To further evaluate our method, we compare it with 3D-SPIHT. 3D-ODETLAP averages 20% better compression than 3D-SPIHT on our eight test datasets, from World Ocean Atlas 2005. Our method provides up to approximately six times better compression on datasets with relatively small variance. Meanwhile, with the same approximate mean error, we demonstrate a significantly smaller maximum error compared to 3D-SPIHT and provide a feature to keep the maximum error under a user-defined limit

Investigation of techniques for inventorying forested regions. Volume 2: Forestry information system requirements and joint use of remotely sensed and ancillary data

The author has identified the following significant results. Effects of terrain topography in mountainous forested regions on LANDSAT signals and classifier training were found to be significant. The aspect of sloping terrain relative to the sun's azimuth was the major cause of variability. A relative insolation factor could be defined which, in a single variable, represents the joint effects of slope and aspect and solar geometry on irradiance. Forest canopy reflectances were bound, both through simulation, and empirically, to have nondiffuse reflectance characteristics. Training procedures could be improved by stratifying in the space of ancillary variables and training in each stratum. Application of the Tasselled-Cap transformation for LANDSAT data acquired over forested terrain could provide a viable technique for data compression and convenient physical interpretations

Soil temperature investigations using satellite acquired thermal-infrared data in semi-arid regions

Thermal-infrared data from the Heat Capacity Mapping Mission satellite were used to map the spatial distribution of diurnal surface temperatures and to estimate mean annual soil temperatures (MAST) and annual surface temperature amplitudes (AMP) in semi-arid east central Utah. Diurnal data with minimal snow and cloud cover were selected for five dates throughout a yearly period and geometrically co-registered. Rubber-sheet stretching was aided by the WARP program which allowed preview of image transformations. Daytime maximum and nighttime minimum temperatures were averaged to generation average daily temperature (ADT) data set for each of the five dates. Five ADT values for each pixel were used to fit a sine curve describing the theoretical annual surface temperature response as defined by a solution of a one-dimensinal heat flow equation. Linearization of the equation produced estimates of MAST and AMP plus associated confidence statistics. MAST values were grouped into classes and displayed on a color video screen. Diurnal surface temperatures and MAST were primarily correlated with elevation

Roving vehicle motion control Quarterly report, 1 Mar. - 31 May 1967

System and subsystem requirements for remote control of roving space vehicle motio

A fast and optimal pathfinder using airborne LiDAR data

Determining the optimal path between two points in a 3D point cloud is a problem that have been addressed in many different situations: from road planning and escape routes determination, to network routing and facility layout. This problem is addressed using different input information, being 3D point clouds one of the most valuables. Its main utility is to save costs, whatever the field of application is. In this paper, we present a fast algorithm to determine the least cost path in an Airborne Laser Scanning point cloud. In some situations, like finding escape routes for instance, computing the solution in a very short time is crucial, and there are not many works developed in this theme. State of the art methods are mainly based on a digital terrain model (DTM) for calculating these routes, and these methods do not reflect well the topography along the edges of the graph. Also, the use of a DTM leads to a significant loss of both information and precision when calculating the characteristics of possible routes between two points. In this paper, a new method that does not require the use of a DTM and is suitable for airborne point clouds, whether they are classified or not, is proposed. The problem is modeled by defining a graph using the information given by a segmentation and a Voronoi Tessellation of the point cloud. The performance tests show that the algorithm is able to compute the optimal path between two points by processing up to 678,820 points per second in a point cloud of 40,000,000 points and 16 km² of extensionThis work has received financial support from the Consellería de Cultura, Educación e Ordenación Universitaria (accreditation 2019-2022 ED431G-2019/04, reference competitive group 2019-2021, ED431C 2018/19) and the European Regional Development Fund (ERDF), which acknowledges the CiTIUS-Research Center in Intelligent Technologies of the University of Santiago de Compostela as a Research Center of the Galician University System. This work was also supported by the Ministry of Economy and Competitiveness, Government of Spain (Grant No. PID2019-104834 GB-I00). We also acknowledge the Centro de Supercomputación de Galicia (CESGA) for the use of their computersS

Synthetic aperture radar/LANDSAT MSS image registration

Algorithms and procedures necessary to merge aircraft synthetic aperture radar (SAR) and LANDSAT multispectral scanner (MSS) imagery were determined. The design of a SAR/LANDSAT data merging system was developed. Aircraft SAR images were registered to the corresponding LANDSAT MSS scenes and were the subject of experimental investigations. Results indicate that the registration of SAR imagery with LANDSAT MSS imagery is feasible from a technical viewpoint, and useful from an information-content viewpoint