TFI-FTS: An efficient transient fault injection and fault-tolerant system for asynchronous circuits on FPGA platform

Designing VLSI digital circuits is challenging tasks because of testing the circuits concerning design time. The reliability and productivity of digital integrated circuits are primarily affected by the defects in the manufacturing process or systems. If the defects are more in the systems, which leads the fault in the systems. The fault tolerant systems are necessary to overcome the faults in the VLSI digital circuits. In this research article, an asynchronous circuits based an effective transient fault injection (TFI) and fault tolerant system (FTS) are modelled. The TFI system generates the faults based on BMA based LFSR with faulty logic insertion and one hot encoded register. The BMA based LFSR reduces the hardware complexity with less power consumption on-chip than standard LFSR method. The FTS uses triple mode redundancy (TMR) based majority voter logic (MVL) to tolerant the faults for asynchronous circuits. The benchmarked 74X-series circuits are considered as an asynchronous circuit for TMR logic. The TFI-FTS module is modeled using Verilog-HDL on Xilinx-ISE and synthesized on hardware platform. The Performance parameters are tabulated for TFI-FTS based asynchronous circuits. The performance of TFI-FTS Module is analyzed with 100% fault coverage. The fault coverage is validated using functional simulation of each asynchronous circuit with fault injection in TFI-FTS Module

Practical Bloom filter based epidemic forwarding and congestion control in DTNs: A comparative analysis

International audienceEpidemic forwarding has been proposed as a forwarding technique to achieve opportunistic communication in delay tolerant networks (DTNs). Even if this technique is well known and widely referred, one has to address several practical problems before using it. Unfortunately, while the literature on DTNs is full of new techniques, very little has been done in comparing them. In particular, while Bloom filters have been proposed to exchange information about the buffer content prior to sending information in order to avoid redundant retransmissions, up to our knowledge no real evaluation has been provided to study the tradeoffs that exist for using Bloom filters in practice. A second practical issue in DTNs is buffer management (resulting from finite buffers) and congestion control (resulting from greedy sources). This has also been the topic of several papers that had already uncovered the difficulty to acquire accurate information mandatory to regulate the data transmission rates and buffer space. In this paper, we fill this gap. We have been implementing a simulation of different proposed congestion control schemes for epidemic forwarding in ns-3 environment. We use this simulation to compare different proposed schemes and to uncover issues that remain in each one of them. Based on this analysis, we proposed some strategies for Bloom filter management based on windowing and describe implementation tradeoffs. Afterwards, we propose a back-pressure rate control as a well as an aging based buffer managing solution to deal with congestion control. By simulating our proposed mechanisms in ns-3 both with random-waypoint mobility and realistic mobility traces coming from San-Francisco taxicabs, we show that the proposed mechanisms alleviate the challenges of using epidemic forwarding in DTN

Multiversioning hardware transactional memory for fail-operational multithreaded applications

Modern safety-critical embedded applications like autonomous driving need to be fail-operational, while high performance and low power consumption are demanded simultaneously. The prevalent fault tolerance mechanisms suffer from disadvantages: Some (e.g. triple modular redundancy) require a substantial amount of duplication, resulting in high hardware costs and power consumption. Others, like lockstep, require supplementary checkpointing mechanisms to recover from errors. Further approaches (e.g. software-based process-level redundancy) cannot handle the indeterminism caused by multithreaded execution. This paper presents a novel approach for fail-operational systems using hardware transactional memory for embedded systems. The hardware transactional memory is extended to support multiple versions, enabling redundant atomic operations and recovery in case of an error. In our FPGA-based evaluation, we executed the PARSEC benchmark suite with fault tolerance on 12 cores. The evaluation shows that multiversioning can successfully recover from all transient errors with an overhead comparable to fault tolerance mechanisms without recovery

Scalable and Reliable Middlebox Deployment

Middleboxes are pervasive in modern computer networks providing functionalities beyond mere packet forwarding. Load balancers, intrusion detection systems, and network address translators are typical examples of middleboxes. Despite their benefits, middleboxes come with several challenges with respect to their scalability and reliability. The goal of this thesis is to devise middlebox deployment solutions that are cost effective, scalable, and fault tolerant. The thesis includes three main contributions: First, distributed service function chaining with multiple instances of a middlebox deployed on different physical servers to optimize resource usage; Second, Constellation, a geo-distributed middlebox framework enabling a middlebox application to operate with high performance across wide area networks; Third, a fault tolerant service function chaining system

Novel fault tolerant Multi-Bit Upset (MBU) Error-Detection and Correction (EDAC) architecture

Desde el punto de vista de seguridad, la certificación aeronáutica de aplicaciones críticas de vuelo requiere diferentes técnicas que son usadas para prevenir fallos en los equipos electrónicos. Los fallos de tipo hardware debido a la radiación solar que existe a las alturas standard de vuelo, como SEU (Single Event Upset) y MCU (Multiple Bit Upset), provocan un cambio de estado de los bits que soportan la información almacenada en memoria. Estos fallos se producen, por ejemplo, en la memoria de configuración de una FPGA, que es donde se definen todas las funcionalidades. Las técnicas de protección requieren normalmente de redundancias que incrementan el coste, número de componentes, tamaño de la memoria y peso. En la fase de desarrollo de aplicaciones críticas de vuelo, generalmente se utilizan una serie de estándares o recomendaciones de diseño como ABD100, RTCA DO-160, IEC62395, etc, y diferentes técnicas de protección para evitar fallos del tipo SEU o MCU. Estas técnicas están basadas en procesos tecnológicos específicos como memorias robustas, codificaciones para detección y corrección de errores (EDAC), redundancias software, redundancia modular triple (TMR) o soluciones a nivel sistema. Esta tesis está enfocada a minimizar e incluso suprimir los efectos de los SEUs y MCUs que particularmente ocurren en la electrónica de avión como consecuencia de la exposición a radiación de partículas no cargadas (como son los neutrones) que se encuentra potenciada a las típicas alturas de vuelo. La criticidad en vuelo que tienen determinados sistemas obligan a que dichos sistemas sean tolerantes a fallos, es decir, que garanticen un correcto funcionamiento aún cuando se produzca un fallo en ellos. Es por ello que soluciones como las presentadas en esta tesis tienen interés en el sector industrial. La Tesis incluye una descripción inicial de la física de la radiación incidente sobre aeronaves, y el análisis de sus efectos en los componentes electrónicos aeronaúticos basados en semiconductor, que desembocan en la generación de SEUs y MCUs. Este análisis permite dimensionar adecuadamente y optimizar los procedimientos de corrección que se propongan posteriormente. La Tesis propone un sistema de corrección de fallos SEUs y MCUs que permita cumplir la condición de Sistema Tolerante a Fallos, a la vez que minimiza los niveles de redundancia y de complejidad de los códigos de corrección. El nivel de redundancia es minimizado con la introducción del concepto propuesto HSB (Hardwired Seed Bits), en la que se reduce la información esencial a unos pocos bits semilla, neutros frente a radiación. Los códigos de corrección requeridos se reducen a la corrección de un único error, gracias al uso del concepto de Distancia Virtual entre Bits, a partir del cual será posible corregir múltiples errores simultáneos (MCUs) a partir de códigos simples de corrección. Un ejemplo de aplicación de la Tesis es la implementación de una Protección Tolerante a Fallos sobre la memoria SRAM de una FPGA. Esto significa que queda protegida no sólo la información contenida en la memoria sino que también queda auto-protegida la función de protección misma almacenada en la propia SRAM. De esta forma, el sistema es capaz de auto-regenerarse ante un SEU o incluso un MCU, independientemente de la zona de la SRAM sobre la que impacte la radiación. Adicionalmente, esto se consigue con códigos simples tales como corrección por bit de paridad y Hamming, minimizando la dedicación de recursos de computación hacia tareas de supervisión del sistema.For airborne safety critical applications certification, different techniques are implemented to prevent failures in electronic equipments. The HW failures at flying heights of aircrafts related to solar radiation such as SEU (Single-Event-Upset) and MCU (Multiple Bit Upset), causes bits alterations that corrupt the information at memories. These HW failures cause errors, for example, in the Configuration-Code of an FPGA that defines the functionalities. The protection techniques require classically redundant functionalities that increases the cost, components, memory space and weight. During the development phase for airborne safety critical applications, different aerospace standards are generally recommended as ABD100, RTCA-DO160, IEC62395, etc, and different techniques are classically used to avoid failures such as SEU or MCU. These techniques are based on specific technology processes, Hardened memories, error detection and correction codes (EDAC), SW redundancy, Triple Modular Redundancy (TMR) or System level solutions. This Thesis is focussed to minimize, and even to remove, the effects of SEUs and MCUs, that particularly occurs in the airborne electronics as a consequence of its exposition to solar radiation of non-charged particles (for example the neutrons). These non-charged particles are even powered at flying altitudes due to aircraft volume. The safety categorization of different equipments/functionalities requires a design based on fault-tolerant approach that means, the system will continue its normal operation even if a failure occurs. The solution proposed in this Thesis is relevant for the industrial sector because of its Fault-tolerant capability. Thesis includes an initial description for the physics of the solar radiation that affects into aircrafts, and also the analyses of their effects into the airborne electronics based on semiconductor components that create the SEUs and MCUs. This detailed analysis allows the correct sizing and also the optimization of the procedures used to correct the errors. This Thesis proposes a system that corrects the SEUs and MCUs allowing the fulfilment of the Fault-Tolerant requirement, reducing the redundancy resources and also the complexity of the correction codes. The redundancy resources are minimized thanks to the introduction of the concept of HSB (Hardwired Seed Bits), in which the essential information is reduced to a few seed bits, neutral to radiation. The correction codes required are reduced to the correction of one error thanks to the use of the concept of interleaving distance between adjacent bits, this allows the simultaneous multiple error correction with simple single error correcting codes. An example of the application of this Thesis is the implementation of the Fault-tolerant architecture of an SRAM-based FPGA. That means that the information saved in the memory is protected but also the correction functionality is auto protected as well, also saved into SRAM memory. In this way, the system is able to self-regenerate the information lost in case of SEUs or MCUs. This is independent of the SRAM area affected by the radiation. Furthermore, this performance is achieved by means simple error correcting codes, as parity bits or Hamming, that minimize the use of computational resources to this supervision tasks for system.Programa Oficial de Doctorado en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Luis Alfonso Entrena Arrontes.- Secretario: Pedro Reviriego Vasallo.- Vocal: Mª Luisa López Vallej

Techniques d'abstraction pour l'analyse et la mitigation des effets dus à la radiation

The main objective of this thesis is to develop techniques that can beused to analyze and mitigate the effects of radiation-induced soft errors in industrialscale integrated circuits. To achieve this goal, several methods have been developedbased on analyzing the design at higher levels of abstraction. These techniquesaddress both sequential and combinatorial SER.Fault-injection simulations remain the primary method for analyzing the effectsof soft errors. In this thesis, techniques which significantly speed-up fault-injectionsimulations are presented. Soft errors in flip-flops are typically mitigated by selectivelyreplacing the most critical flip-flops with hardened implementations. Selectingan optimal set to harden is a compute intensive problem and the second contributionconsists of a clustering technique which significantly reduces the number offault-injections required to perform selective mitigation.In terrestrial applications, the effect of soft errors in combinatorial logic hasbeen fairly small. It is known that this effect is growing, yet there exist few techniqueswhich can quickly estimate the extent of combinatorial SER for an entireintegrated circuit. The third contribution of this thesis is a hierarchical approachto combinatorial soft error analysis.Systems-on-chip are often developed by re-using design-blocks that come frommultiple sources. In this context, there is a need to develop and exchange reliabilitymodels. The final contribution of this thesis consists of an application specificmodeling language called RIIF (Reliability Information Interchange Format). Thislanguage is able to model how faults at the gate-level propagate up to the block andchip-level. Work is underway to standardize the RIIF modeling language as well asto extend it beyond modeling of radiation-induced failures.In addition to the main axis of research, some tangential topics were studied incollaboration with other teams. One of these consisted in the development of a novelapproach for protecting ternary content addressable memories (TCAMs), a specialtype of memory important in networking applications. The second supplementalproject resulted in an algorithm for quickly generating approximate redundant logicwhich can protect combinatorial networks against permanent faults. Finally anapproach for reducing the detection time for errors in the configuration RAM forField-Programmable Gate-Arrays (FPGAs) was outlined.Les effets dus à la radiation peuvent provoquer des pannes dans des circuits intégrés. Lorsqu'une particule subatomique, fait se déposer une charge dans les régions sensibles d'un transistor cela provoque une impulsion de courant. Cette impulsion peut alors engendrer l'inversion d'un bit ou se propager dans un réseau de logique combinatoire avant d'être échantillonnée par une bascule en aval.Selon l'état du circuit au moment de la frappe de la particule et selon l'application, cela provoquera une panne observable ou non. Parmi les événements induits par la radiation, seule une petite portion génère des pannes. Il est donc essentiel de déterminer cette fraction afin de prédire la fiabilité du système. En effet, les raisons pour lesquelles une perturbation pourrait être masquée sont multiples, et il est de plus parfois difficile de préciser ce qui constitue une erreur. A cela s'ajoute le fait que les circuits intégrés comportent des milliards de transistors. Comme souvent dans le contexte de la conception assisté par ordinateur, les approches hiérarchiques et les techniques d'abstraction permettent de trouver des solutions.Cette thèse propose donc plusieurs nouvelles techniques pour analyser les effets dus à la radiation. La première technique permet d'accélérer des simulations d'injections de fautes en détectant lorsqu'une faute a été supprimée du système, permettant ainsi d'arrêter la simulation. La deuxième technique permet de regrouper en ensembles les éléments d'un circuit ayant une fonction similaire. Ensuite, une analyse au niveau des ensemble peut être faite, identifiant ainsi ceux qui sont les plus critiques et qui nécessitent donc d'être durcis. Le temps de calcul est ainsi grandement réduit.La troisième technique permet d'analyser les effets des fautes transitoires dans les circuits combinatoires. Il est en effet possible de calculer à l'avance la sensibilité à des fautes transitoires de cellules ainsi que les effets de masquage dans des blocs fréquemment utilisés. Ces modèles peuvent alors être combinés afin d'analyser la sensibilité de grands circuits. La contribution finale de cette thèse consiste en la définition d'un nouveau langage de modélisation appelé RIIF (Reliability Information Ineterchange Format). Ce langage permet de décrire le taux des fautes dans des composants simples en fonction de leur environnement de fonctionnement. Ces composants simples peuvent ensuite être combinés permettant ainsi de modéliser la propagation de leur fautes vers des pannes au niveau système. En outre, l'utilisation d'un langage standard facilite l'échange de données de fiabilité entre les partenaires industriels.Au-delà des contributions principales, cette thèse aborde aussi des techniques permettant de protéger des mémoires associatives ternaires (TCAMs). Les approches classiques de protection (codes correcteurs) ne s'appliquent pas directement. Une des nouvelles techniques proposées consiste à utiliser une structure de données qui peut détecter, d'une manière statistique, quand le résultat n'est pas correct. La probabilité de détection peut être contrôlée par le nombre de bits alloués à cette structure. Une autre technique consiste à utiliser un détecteur de courant embarqué (BICS) afin de diriger un processus de fond directement vers le région touchée par une erreur. La contribution finale consiste en un algorithme qui permet de synthétiser de la logique combinatoire afin de protéger des circuits combinatoires contre les fautes transitoires.Dans leur ensemble, ces techniques facilitent l'analyse des erreurs provoquées par les effets dus à la radiation dans les circuits intégrés, en particulier pour les très grands circuits composés de blocs provenant de divers fournisseurs. Des techniques pour mieux sélectionner les bascules/flip-flops à durcir et des approches pour protéger des TCAMs ont étés étudiées