SDDV: scalable data dissemination in vehicular ad hoc networks

An important challenge in the domain of vehicular ad hoc networks (VANET) is the scalability of data dissemination. Under dense traffic conditions, the large number of communicating vehicles can easily result in a congested wireless channel. In that situation, delays and packet losses increase to a level where the VANET cannot be applied for road safety applications anymore. This paper introduces scalable data dissemination in vehicular ad hoc networks (SDDV), a holistic solution to this problem. It is composed of several techniques spread across the different layers of the protocol stack. Simulation results are presented that illustrate the severity of the scalability problem when applying common state-of-the-art techniques and parameters. Starting from such a baseline solution, optimization techniques are gradually added to SDDV until the scalability problem is entirely solved. Besides the performance evaluation based on simulations, the paper ends with an evaluation of the final SDDV configuration on real hardware. Experiments including 110 nodes are performed on the iMinds w-iLab.t wireless lab. The results of these experiments confirm the results obtained in the corresponding simulations

Evaluation study of IEEE 1609.4 performance for safety and non-safety messages dissemination

The IEEE 1609.4 was developed to support multi-channel operation and channel switching procedure in order to provide both safety and non-safety vehicular applications. However, this protocol has some drawback because it does not make efficient usage of channel bandwidth resources for single radio WAVE devices and suffer from high bounded delay and lost packet especially for large-scale networks in terms of the number of active nodes. This paper evaluates IEEE 1609.4 multi-channel protocol performance for safety and non-safety application and compare it with the IEEE 802.11p single channel protocol. Multi-channel and single channel protocols are analyzed in different environments to investigate their performance. By relying on a realistic dataset and using OMNeT++ simulation tool as network simulator, SUMO as traffic simulator and coupling them by employing Veins framework. Performance evaluation results show that the delay of single channel protocol IEEE 802.11p has been degraded 36% compared with multi-channel protocol

The Dynamics of Vehicular Networks in Urban Environments

Vehicular Ad hoc NETworks (VANETs) have emerged as a platform to support intelligent inter-vehicle communication and improve traffic safety and performance. The road-constrained, high mobility of vehicles, their unbounded power source, and the emergence of roadside wireless infrastructures make VANETs a challenging research topic. A key to the development of protocols for inter-vehicle communication and services lies in the knowledge of the topological characteristics of the VANET communication graph. This paper explores the dynamics of VANETs in urban environments and investigates the impact of these findings in the design of VANET routing protocols. Using both real and realistic mobility traces, we study the networking shape of VANETs under different transmission and market penetration ranges. Given that a number of RSUs have to be deployed for disseminating information to vehicles in an urban area, we also study their impact on vehicular connectivity. Through extensive simulations we investigate the performance of VANET routing protocols by exploiting the knowledge of VANET graphs analysis.Comment: Revised our testbed with even more realistic mobility traces. Used the location of real Wi-Fi hotspots to simulate RSUs in our study. Used a larger, real mobility trace set, from taxis in Shanghai. Examine the implications of our findings in the design of VANET routing protocols by implementing in ns-3 two routing protocols (GPCR & VADD). Updated the bibliography section with new research work

In-vehicle channel sounding in the 5.8-GHz band

The article reports vehicular channel measurements in the frequency band of 5.8 GHz for IEEE 802.11p standard. Experiments for both intra-vehicle and out-of-vehicle environments were carried out. It was observed that the large-scale variations (LSVs) of the power delay profiles (PDPs) can be best described through a two-term exponential decay model, in contrast to the linear models which are suitable for popular ultra-wideband (UWB) systems operating in the 3- to 11-GHz band. The small-scale variations (SSVs) are separated from the PDP by subtracting the LSV and characterized utilizing logistic, generalized extreme value (GEV), and normal distributions. Two sample Kolmogorov-Smirnov (K-S) tests validated that the logistic distribution is optimal for in-car, whereas the GEV distribution serves better for out-of-car measurements. For each measurement, the LSV trend was used to construct the respective channel impulse response (CIR), i.e., tap gains at different delays. Next, the CIR information is fed to an 802.11p simulation testbed to evaluate the bit error rate (BER) performance, following a Rician model. The BER results strongly vouch for the suitability of the protocol for in-car as well as out-of-car wireless applications in stationary environments.The article reports vehicular channel measurements in the frequency band of 5.8 GHz for IEEE 802.11p standard. Experiments for both intra-vehicle and out-of-vehicle environments were carried out. It was observed that the large-scale variations (LSVs) of the power delay profiles (PDPs) can be best described through a two-term exponential decay model, in contrast to the linear models which are suitable for popular ultra-wideband (UWB) systems operating in the 3- to 11-GHz band. The small-scale variations (SSVs) are separated from the PDP by subtracting the LSV and characterized utilizing logistic, generalized extreme value (GEV), and normal distributions. Two sample Kolmogorov-Smirnov (K-S) tests validated that the logistic distribution is optimal for in-car, whereas the GEV distribution serves better for out-of-car measurements. For each measurement, the LSV trend was used to construct the respective channel impulse response (CIR), i.e., tap gains at different delays. Next, the CIR information is fed to an 802.11p simulation testbed to evaluate the bit error rate (BER) performance, following a Rician model. The BER results strongly vouch for the suitability of the protocol for in-car as well as out-of-car wireless applications in stationary environments

Models and Performance of VANET based Emergency Braking

The network research community is working in the field of automotive to provide VANET based safety applications to reduce the number of accidents, deaths, injuries and loss of money. Several approaches are proposed and investigated in VANET literature, but in a completely network-oriented fashion. Most of them do not take into account application requirements and no one considers the dynamics of the vehicles. Moreover, message repropagation schemes are widely proposed without investigating their benefits and using very complicated approaches. This technical report, which is derived from the Master Thesis of Michele Segata, focuses on the Emergency Electronic Brake Lights (EEBL) safety application, meant to send warning messages in the case of an emergency brake, in particular performing a joint analysis of network requirements and provided application level benefits. The EEBL application is integrated within a Collaborative Adaptive Cruise Control (CACC) which uses network-provided information to automatically brake the car if the driver does not react to the warning. Moreover, an information aggregation scheme is proposed to analyze the benefits of repropagation together with the consequent increase of network load. This protocol is compared to a protocol without repropagation and to a rebroadcast protocol found in the literature (namely the weighted p-persistent rebroadcast). The scenario is a highway stretch in which a platoon of vehicles brake down to a complete stop. Simulations are performed using the NS_3 network simulation in which two mobility models have been embedded. The first one, which is called Intelligent Driver Model (IDM) emulates the behavior of a driver trying to reach a desired speed and braking when approaching vehicles in front. The second one (Minimizing Overall Braking Induced by Lane change (MOBIL)), instead, decides when a vehicle has to change lane in order to perform an overtake or optimize its path. The original simulator has been modified by - introducing real physical limits to naturally reproduce real crashes; - implementing a CACC; - implementing the driver reaction when a warning is received; - implementing different network protocols. The tests are performed in different situations, such as different number of lanes (one to five), different average speeds, different network protocols and different market penetration rates and they show that: - the adoption of this technology considerably decreases car accidents since the overall average maximum deceleration is reduced; - network load depends on application-level details, such as the implementation of the CACC; - VANET safety application can improve safety even with a partial market penetration rate; - message repropagation is important to reduce the risk of accidents when not all vehicles are equipped; - benefits are gained not only by equipped vehicles but also by unequipped ones

Development of new PCR primers by comparative genomics for the detection of Helicobacter suis in gastric biopsy specimens

Background: Although the infection rate of Helicobacter suis is significantly lower than that of Helicobacter pylori, the H. suis infection is associated with a high rate of gastric mucosa-associated lymphoid tissue (MALT) lymphoma. In addition, in vitro cultivation of H. suis remains difficult, and some H. suis-infected patients show negative results on the urea breath test (UBT). Materials and Methods: Female C57BL/6J mice were orally inoculated with mouse gastric mucosal homogenates containing H. suis strains TKY or SNTW101 isolated from a cynomolgus monkey or a patient suffering from nodular gastritis, respectively. The high-purity chromosomal DNA samples of H. suis strains TKY and SNTW101 were prepared from the infected mouse gastric mucosa. The SOLiD sequencing of two H. suis genomes enabled comparative genomics of 20 Helicobacter and 11 Campylobacter strains for the identification of the H. suis-specific nucleotide sequences. Results: Oral inoculation with mouse gastric mucosal homogenates containing H. suis strains TKY and SNTW101 induced gastric MALT lymphoma and the formation of gastric lymphoid follicles, respectively, in C57BL/6J mice. Two conserved nucleotide sequences among six H. suis strains were identified and were used to design diagnostic PCR primers for the detection of H. suis. Conclusions: There was a strong association between the H. suis infection and gastric diseases in the C57BL/6 mouse model. PCR diagnosis using an H. suis-specific primer pair is a valuable method for detecting H. suis in gastric biopsy specimens

Approximation of the IEEE 802.11p standard using commercial off-the-shelf IEEE 802.11a hardware

IEEE 802.11p hardware is hard to find. Previous research efforts often relied on project-specific prototype implementations which are characterized by a high cost and are not always available to the entire research community. Commercially available turnkey implementations are rare and quite expensive compared to commercial of-the-shelf (COTS) IEEE 802.11a/b/g hardware. However, the difference between the IEEE 802.11p amendment and the other IEEE 802.11 standards is quite small. It can be seen as a combination of the IEEE 802.11a and IEEE 802.11e standards, with some specific adjustments. This paper presents how an approximation of the IEEE 802.11p standard can be implemented using COTS IEEE 802.11a hardware and some specific software adjustments. This way, vehicular test infrastructures can be established in a much more cost effective manner, and existing IEEE 802.11 wireless testbeds can be used to support VANET research