Testing for delay defects utilizing test data compression techniques

textAs technology shrinks new types of defects are being discovered and new fault models are being created for those defects. Transition delay and path delay fault models are two such models that have been created, but they still fall short in that they are unable to obtain a high test coverage of smaller delay defects; these defects can cause functional behavior to fail and also indicate potential reliability issues. The first part of this dissertation addresses these problems by presenting an enhanced timing-based delay fault testing technique that incorporates the use of standard delay ATPG, along with timing information gathered from standard static timing analysis. Utilizing delay fault patterns typically increases the test data volume by 3-5X when compared to stuck-at patterns. Combined with the increase in test data volume associated with the increase in gate count that typically accompanies the miniaturization of technology, this adds up to a very large increase in test data volume that directly affect test time and thus the manufacturing cost. The second part of this dissertation presents a technique for improving test compression and reducing test data volume by using multiple expansion ratios while determining the configuration of the scan chains for each of the expansion ratios using a dependency analysis procedure that accounts for structural dependencies as well as free variable dependencies to improve the probability of detecting faults. Finally, this dissertation addresses the problem of unknown values (X’s) in the output response data corrupting the data and degrading the performance of the output response compactor and thus the overall amount of test compression. Four techniques are presented that focus on handling response data with large percentages of X’s. The first uses X-canceling MISR architecture that is based on deterministically observing scan cells, and the second is a hybrid approach that combines a simple X-masking scheme with the X-canceling MISR for further gains in test compression. The third and fourth techniques revolve around reiterative LFSR X-masking, which take advantage of LFSR-encoded masks that can be reused for multiple scan slices in novel ways.Electrical and Computer Engineerin

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

Compressed Skewed-Load Delay Test Generation Based on Evolution and Deterministic Initialization of Populations

The current design and manufacturing semiconductor technologies require to test the products against delay related defects. However, complex acpSOC require low-overhead testability methods to keep the test cost at an acceptable level. Skewed-load tests seem to be the appropriate way to test delay faults in these acpSOC because the test application requires only one storage element per scan cell. Compressed skewed-load test generator based on genetic algorithm is proposed for wrapper-based logic cores of acpSOC. Deterministic population initialization is used to ensure the highest achievable aclTDF coverage for the given wrapper and scan cell order. The developed method performs test data compression by generating test vectors containing already overlapped test vector pairs. The experimental results show high fault coverages, decreased test lengths and better scalability in comparison to recent methods

Low-Capture-Power Test Generation for Scan-Based At-Speed Testing

Scan-based at-speed testing is a key technology to guarantee timing-related test quality in the deep submicron era. However, its applicability is being severely challenged since significant yield loss may occur from circuit malfunction due to excessive IR drop caused by high power dissipation when a test response is captured. This paper addresses this critical problem with a novel low-capture-power X-filling method of assigning 0\u27s and 1\u27s to unspecified (X) bits in a test cube obtained during ATPG. This method reduces the circuit switching activity in capture mode and can be easily incorporated into any test generation flow to achieve capture power reduction without any area, timing, or fault coverage impact. Test vectors generated with this practical method greatly improve the applicability of scan-based at-speed testing by reducing the risk of test yield lossIEEE International Conference on Test, 2005, 8 November 2005, Austin, TX, US

Improving timing verification and delay testing methodologies for IC designs

textThe task of ensuring the correct temporal behavior of IC designs, both before and after fabrication, is extremely important. It is becoming even more imperative as the demand for performance increases and process technology advances into the deep sub-micron region. This dissertation tackles the key issues in the timing verification and delay testing methodologies. An efficient methodology is presented to identify false timing paths in the timing verification methodology which utilizes ATPG technique and timing information from an ordered list of timing paths according to the delay information. This dissertation also presents a speed binning methodology which utilizes structural delay tests successfully instead of functional tests. In addition, it establishes a methodology which quantifies the correlation between the timing verification prediction and actual silicon measurement of timing paths. This quantification methodology lays the foundation for further research to study the impact of deep submicron effects on design performanceElectrical and Computer Engineerin

Efficient Path Delay Test Generation with Boolean Satisfiability

This dissertation focuses on improving the accuracy and efficiency of path delay test generation using a Boolean satisfiability (SAT) solver. As part of this research, one of the most commonly used SAT solvers, MiniSat, was integrated into the path delay test generator CodGen. A mixed structural-functional approach was implemented in CodGen where longest paths were detected using the K Longest Path Per Gate (KLPG) algorithm and path justification and dynamic compaction were handled with the SAT solver. Advanced techniques were implemented in CodGen to further speed up the performance of SAT based path delay test generation using the knowledge of the circuit structure. SAT solvers are inherently circuit structure unaware, and significant speedup can be availed if structure information of the circuit is provided to the SAT solver. The advanced techniques explored include: Dynamic SAT Solving (DSS), Circuit Observability Don’t Care (Cir-ODC), SAT based static learning, dynamic learnt clause management and Approximate Observability Don’t Care (ACODC). Both ISCAS 89 and ITC 99 benchmarks as well as industrial circuits were used to demonstrate that the performance of CodGen was significantly improved with MiniSat and the use of circuit structure

Multi-Cycle at Speed Test

In this research, we focus on the development of an algorithm that is used to generate a minimal number of patterns for path delay test of integrated circuits using the multi-cycle at-speed test. We test the circuits in functional mode, where multiple functional cycles follow after the test pattern scan-in operation. This approach increases the delay correlation between the scan and functional test, due to more functionally realistic power supply noise. We use multiple at-speed cycles to compact K-longest paths per gate tests, which reduces the number of scan patterns. After a path is generated, we try to place each path in the first pattern in the pattern pool. If the path does not fit due to conflicts, we attempt to place it in later functional cycles. This compaction approach retains the greedy nature of the original dynamic compaction algorithm where it will stop if the path fits into a pattern. If the path is not able to compact in any of the functional cycles of patterns in the pool, we generate a new pattern. In this method, each path delay test is compared to at-speed patterns in the pool. The challenge is that the at-speed delay test in a given at-speed cycle must have its necessary value assignments set up in previous (preamble) cycles, and have the captured results propagated to a scan cell in the later (coda) cycles. For instance, if we consider three at-speed (capture) cycles after the scan-in operation, and if we need to place a fault in the first capture cycle, then we must generate it with two propagation cycles. In this case, we consider these propagation cycles as coda cycles, so the algorithm attempts to select the most observable path through them. Likewise, if we are placing the path test in the second capture cycle, then we need one preamble cycle and one coda cycle, and if we are placing the path test in the third capture cycle, we require two preamble cycles with no coda cycles

A survey of scan-capture power reduction techniques

With the advent of sub-nanometer geometries, integrated circuits (ICs) are required to be checked for newer defects. While scan-based architectures help detect these defects using newer fault models, test data inflation happens, increasing test time and test cost. An automatic test pattern generator (ATPG) exercise’s multiple fault sites simultaneously to reduce test data which causes elevated switching activity during the capture cycle. The switching activity results in an IR drop exceeding the devices under test (DUT) specification. An increase in IR-drop leads to failure of the patterns and may cause good DUTs to fail the test. The problem is severe during at-speed scan testing, which uses a functional rated clock with a high frequency for the capture operation. Researchers have proposed several techniques to reduce capture power. They used various methods, including the reduction of switching activity. This paper reviews the recently proposed techniques. The principle, algorithm, and architecture used in them are discussed, along with key advantages and limitations. In addition, it provides a classification of the techniques based on the method used and its application. The goal is to present a survey of the techniques and prepare a platform for future development in capture power reduction during scan testing

Evolution of Test Programs Exploiting a FSM Processor Model

Microprocessor testing is becoming a challenging task, due to the increasing complexity of modern architectures. Nowadays, most architectures are tackled with a combination of scan chains and Software-Based Self-Test (SBST) methodologies. Among SBST techniques, evolutionary feedback-based ones prove effective in microprocessor testing: their main disadvantage, however, is the considerable time required to generate suitable test programs. A novel evolutionary-based approach, able to appreciably reduce the generation time, is presented. The proposed method exploits a high-level representation of the architecture under test and a dynamically built Finite State Machine (FSM) model to assess fault coverage without resorting to time-expensive simulations on low-level models. Experimental results, performed on an OpenRISC processor, show that the resulting test obtains a nearly complete fault coverage against the targeted fault mode

REDUCING POWER DURING MANUFACTURING TEST USING DIFFERENT ARCHITECTURES

Power during manufacturing test can be several times higher than power consumption in functional mode. Excessive power during test can cause IR drop, over-heating, and early aging of the chips. In this dissertation, three different architectures have been introduced to reduce test power in general cases as well as in certain scenarios, including field test. In the first architecture, scan chains are divided into several segments. Every segment needs a control bit to enable capture in a segment when new faults are detectable on that segment for that pattern. Otherwise, the segment should be disabled to reduce capture power. We group the control bits together into one or more control chains. To address the extra pin(s) required to shift data into the control chain(s) and significant post processing in the first architecture, we explored a second architecture. The second architecture stitches the control bits into the chains they control as EECBs (embedded enable capture bits) in between the segments. This allows an ATPG software tool to automatically generate the appropriate EECB values for each pattern to maintain the fault coverage. This also works in the presence of an on-chip decompressor. The last architecture focuses primarily on the self-test of a device in a 3D stacked IC when an existing FPGA in the stack can be programmed as a tester. We show that the energy expended during test is significantly less than would be required using low power patterns fed by an on-chip decompressor for the same very short scan chains