Planar microwave filters with electronically tunability and other novel configurations

In order to meet the increasing demands of advance wireless communications and radar systems, several novel types of bandpass filters and bandstop filters have been developed in this thesis. A new type of varactor-tuned dual-mode bandpass filters have been presented to achieve a nearly constant absolute bandwidth over a wide tuning range by using a single DC bias circuit. Since the two operating modes (i.e., the odd and even modes) in a dualmode microstrip open-loop resonator do not couple to each other, tuning the passband frequency is accomplished by merely changing the two modal frequencies proportionally. Design equations and procedures are derived, and two two-pole tunable bandpass filters and a four-pole tunable bandpass filter of this type are demonstrated experimentally. Miniature microstrip doublet dual-mode filters that exhibit quasi-elliptic function response without using any cross coupling have been developed. It shows that a single two-pole filter or the doublet can produce two transmission zeros resulting from a double behaviour of the dual-mode resonator of this type. Electromagnetic (EM) simulation and experiment results of the proposed filters are described. Parallel feed configuration of a microstrip quasi-elliptic function bandpass filter has been built with a pair of open-loop dual-mode resonators. By employing this new coupling scheme, a novel filter topology with three-pole quasi-elliptic function frequency response can be obtained, leading to good passband performance, such as low insertion loss and good matching at the mid-band of passband. A designed three-pole bandpass filter of this type is demonstrated experimentally. A new class of dual-band filters based on non-degenerate dual-mode microstrip slow-wave open-loop resonators, which support two non-degenerate modes that do not couple, have been introduced. Different feed schemes that affect the filtering characteristics are investigated. Examples of dual-band filters of this type are described with simulation and experiment results. iii In order to achieve a wide spurious-free upper passband, a novel design of bandstop filter with cancellation of first spurious mode by using coupled three-section step impedance resonators (SIRs) has been developed. This cancellation occurs when two transmission poles coincide with the first spurious mode (transmission zero) by properly choosing the step impedance ratio and the gap between the SIR and the main transmission line. A stripline bandstop filter and a microstrip bandstop filter of this type are designed, fabricated and tested. As a preliminary investigation, the microstrip filter is tuned electronically using ferroelectric thin film varactors

Development of tunable and miniature microwave filters for modern wireless communications

Due to the increasing demand for new wireless services and applications, the high level of integration and the coexistence of multi-standard (MS) or multi-band operations into a single device are becoming defining trends in designing microwave filters. This has driven considerable technological advances in reconfigurable/tunable and miniaturized filters. More specifically, reconfigurable/tunable filters that tune to different frequency bands instead of classical filter banks have great potential to significantly reduce the system size and complexity; while reducing the filter size becomes essential to achieve the highest degree of integration density in compact and portable wireless devices. In the light of this scenario, the objective of this dissertation is to develop the new design technologies, concepts and filtering configurations for tunable microstrip filters and compact passive microwave filters. To this aim, this dissertation is divided into two main parts. The first part (Part I) focuses on the designs of novel varactor-tuned microstrip filters with advanced performances. In this aspect, new topologies for realizing tunable lowpass and highpass filters are firstly developed. State-of-the-art performances, including wide tuning range, high selectivity with multiple transmission zeros, low insertion loss and compact size for all the tuning states are obtained in both of these filters. Secondly, two novel classes of tunable bandpass filters are presented. One of them is designed based on varactor-loaded parallel-coupled microstrip lines (PCML) and short-circuited stubs, which allows the lower passband edge together with two transmission zeros located around the lower passband skirt to be reconfigured separately. While the other tunable bandpass filter is constructed by the combination of tunable bandpass and lowpass filters, featuring both centre frequency and bandwidth tunabilities, as well as high selectivity with abundant transmission zeros. Furthermore, a new concept of tunable lossy filter is demonstrated, which attempts to achieve an equivalent high-Q tunable performance by using low-Q resonators. This concept makes the presented tunable combline filter interesting for some frequency-agile applications in which the low in-band loss variation and high selectivity are much desired while the absolute insertion loss can be a tradeoff. The second part (Part II) is devoted to the design of miniaturized passive microwave filters with improved characteristics. For this, the concept of artificial right-handed and left-handed transmission lines are applied to the signal interference filtering topology, which results in a compact circuit size and good out-of-band performance. In particular, for a further size reduction, such filter is implemented in the forms of multilayered structure by using liquid crystal polymer (LCP) technology. Additionally, another two types of miniaturized bandpass filters using stepped impedance resonators are demonstrated, which are implemented based on different fabrication processes (i.e. LCP bonded multilayer PCB technology and a standard planar PCB technology). Among their main features, the compact size, wide passband, broad stopband with multiple transmission zeros and circuit simplicity are highlighted. For all the proposed design techniques and filtering structures, exhaustive theoretical analyses are done, and design equations and guide rules are provided. Furthermore, all the proposed schemes and/or ideas have been experimentally validated through the design, implementation and measurement of different filters. The fabrication processes of multilayer technology utilized: liquid crystal polymer (LCP) technology and liquid crystal polymer (LCP) bonded multilayer printed circuit board (PCB) technology, are also demonstrated for reference. All of the results achieved in this dissertation make the proposed filters very attractive for their use in modern wireless communication systems

Development of turnable and miniature microwave filters for modern wireless communication

Due to the increasing demand for new wireless services and applications, the high level of integration and the coexistence of multi-standard (MS) or multi-band operations into a single device are becoming defining trends in designing microwave filters. This has driven considerable technological advances in reconfigurable/tunable and miniaturized filters. More specifically, reconfigurable/tunable filters that tune to different frequency bands instead of classical filter banks have great potential to significantly reduce the system size and complexity; while reducing the filter size becomes essential to achieve the highest degree of integration density in compact and portable wireless devices. In the light of this scenario, the objective of this dissertation is to develop the new design technologies, concepts and filtering configurations for tunable microstrip filters and compact passive microwave filters. To this aim, this dissertation is divided into two main parts. The first part (Part I) focuses on the designs of novel varactor-tuned microstrip filters with advanced performances. In this aspect, new topologies for realizing tunable lowpass and highpass filters are firstly developed. State-of-the-art performances, including wide tuning range, high selectivity with multiple transmission zeros, low insertion loss and compact size for all the tuning states are obtained in both of these filters. Secondly, two novel classes of tunable bandpass filters are presented. One of them is designed based on varactor-loaded parallel-coupled microstrip lines (PCML) and short-circuited stubs, which allows the lower passband edge together with two transmission zeros located around the lower passband skirt to be reconfigured separately. While the other tunable bandpass filter is iii constructed by the combination of tunable bandpass and lowpass filters, featuring both centre frequency and bandwidth tunabilities, as well as high selectivity with abundant transmission zeros. Furthermore, a new concept of tunable lossy filter is demonstrated, which attempts to achieve an equivalent high-Q tunable performance by using low-Q resonators. This concept makes the presented tunable combline filter interesting for some frequency-agile applications in which the low in-band loss variation and high selectivity are much desired while the absolute insertion loss can be a tradeoff. The second part (Part II) is devoted to the design of miniaturized passive microwave filters with improved characteristics. For this, the concept of artificial right-handed and left-handed transmission lines are applied to the signal interference filtering topology, which results in a compact circuit size and good out-of-band performance. In particular, for a further size reduction, such filter is implemented in the forms of multilayered structure by using liquid crystal polymer (LCP) technology. Additionally, another two types of miniaturized bandpass filters using stepped impedance resonators are demonstrated, which are implemented based on different fabrication processes (i.e. LCP bonded multilayer PCB technology and a standard planar PCB technology). Among their main features, the compact size, wide passband, broad stopband with multiple transmission zeros and circuit simplicity are highlighted. For all the proposed design techniques and filtering structures, exhaustive theoretical analyses are done, and design equations and guide rules are provided. Furthermore, all the proposed schemes and/or ideas have been experimentally validated through the design, implementation and measurement of different filters. The fabrication processes of multilayer technology utilized: liquid crystal polymer (LCP) technology and liquid crystal polymer (LCP) bonded multilayer printed circuit board (PCB) technology, are also demonstrated for reference. All of the results achieved in this dissertation make the proposed filters very attractive for their use in modern wireless communication systems.MultiWaves Project (PIRSES-GA-2010-247532) of the Seventh Framework Programme (FP7), European Commission

Miniaturised and reconfigurable planar filters for ultra-wideband applications

An increasing demand for electromagnetic spectrum has resulted from the emergence of feature-rich and faster throughputs wireless applications. This necessitates the developments of dynamic reconfigurable or multifunctional systems to better exploit the existing spectrum. Future wireless devices will be expected to communicate over several bands with various other devices in order to fine tune the services they provide to the user. Each band may require a separate RF transceiver and such modern wireless multi-band multi-mode communication systems call for high performance, highly integrated compact modules. Since the Federal Communications Commission (FCC) released the unlicensed frequency band 3.1-10.6 GHz for ultra-wideband (UWB) commercial communications, the development race for commercialising UWB technology has seen a dramatic increase around the world. The aim of this research is to develop reconfigurable planar microwave filters for ultrawideband applications. The project investigates some key design issues of reconfigurable filters, which are being observed constantly in the latest development and realisation of microwave filters. Both analytical and numerical methods are performed to construct a realistic and functional design. Two different types of frequency reconfigurability are investigated in this thesis: discrete (e.g. PIN diode, Optical switch) and continuous (e.g. varactor diode). Using the equivalent circuits and considering the direct coupled filter structure in most cases, several topologies with attractive features are developed for future communication systems. The proposed works may be broadly categorised into three sections as follows. The first section explores a square ring shape close loop resonator along with an opencircuited stub in the symmetry plane. To realise a reconfigurable frequency states within the same spectrum, an innovative approach is developed for this case. An optical or photoconductive switch, comprised of a silicon die activated using near infrared light is investigated as a substitute of PIN diode and performances are evaluated to compare the feasibilities. In addition, a in-band interference rejection technique via externally coupled Tshape resonator is shown. However, it is observed that both structures achieve significant size reductions by utilising the inner part of the resonators. To improve the filter selectivity, a convenient design approach generating a pair of transmission zeros between both passband edges and a single zero in the stop band for harmonic suppression is discussed in the second section. Moreover, the development of notched rejection bands are studied and several novel methods to create a single and multiple notched bands employing the square ring shape structure are proposed. On inspection, it is found that the notch structure can be implemented without deteriorating the filter performances. The discussions are supplemented with detailed design examples which are accompanied by theoretical, simulated and experimental results in order to illustrate the filter development process and showcase practical filter performance. The third section reveals a novel highly compact planar dual-mode resonator with sharp rejections characteristics for UWB applications. A bandwidth reconfiguring technique is demonstrated by splitting its even-mode resonance. Filter structure with the dual-mode resonator is shown to have a relatively wide tuning range, significantly low insertion loss and a constant selectivity along with frequency variations in comparison to similar published works. Finally, the earlier dual-mode structure are modified to realise a dual wideband behaviour. A detail analysis with comprehensive design procedures is outlined and a solution for controlling the frequency bandwidths independently according to the application interest is provided. In line with the previous section, experimental verification is presented to support and supplement the discussions

Microstrip diplexer for recent wireless communities

The diplexer is a dual-filter circuit with three ports that may share an antenna across two different frequency channels. As long as each band can be employed for sending and receiving signals, this technology can be used for multiple transmitters running on various frequencies. This paper will first present an overview of the diplexer concept, its importance in wireless networks, and its difference with duplexers. Then, the microstrip transmission line and its variation are discussed, as the filters and diplexers are designed using transmission lines. Typical electrical specifications are presented with measurement methods as well

Lossy Resonator With High Q For Switchable Absorptive Bandstop To Bandpass Filter

New developments in the design of the switchable microwave filters in some cognitive radio system are essential to meet the ever increasing demands to discriminate between wanted and unwanted signals. There also has a demand for miniaturization of microwave communications systems. A compact design can be achieved through the implementation of planar microstrip technology. However, conventional electronically tunable bandstop filters suffer performance degradation due to the finite unloaded Q of the resonators and also the loss associated with the switching elements. Therefore, two low Q lossy resonator filter topology has been implemented where the topology can be used to partially compensate for the loss where a high Q absorptive bandstop filter can be achieved. The filter consists of λ/2 resonator with K-inverter, parallel with an Allpass nominally-90°-phase-shift element. A frequency agile bandstop filter based on this topology has been developed, but such filters as well as conventional switchable bandstop filters encounter performance degradation in terms of tuning bandwidth and stopband bandwidth due to the frequency dependant losses and couplings. Through this thesis a new switchable microwave filter is investigated and developed, where this filter is able to switch from high Q absorptive bandstop response (ON state) to bandpass response (OFF state). This switchable filter is designed using four different types of resonator which are parallel coupled, dual mode ring, stepped impedance dual mode and T-shape. The parallel coupled resonator consisted of two low-Q lossy resonator connected with 90° wavelength and with correct k-inverter to produce high Q absorptive bandstop response. T-shape resonator consisted of T resonator coupled with 90° wavelength. While for the dual mode ring resonator structure is composed by two degenerate modes or splitting resonant frequencies, where the ring can be excited by perturbing stub. For stepped impedance resonator, the structure is consisted of the stepped impedance resonator with mid-plane of via hole and connected with 90° wavelength to achieve the high Q absorptive bandstop response. The filters are integrated with switching element, such as PIN and a varactor diode to switch the filter response and biasing circuit is needed to make the PIN or the varactor diode working properly. The absorptive bandstop filter operates at 2.4 GHz where S11 is below than 15 dB and S21 has high selectivity with the narrow bandstop response with high Q factor. The unloaded Q factor of the absorptive bandstop filter is more than 60 for measuring and 150 for simulation. For a bandpass response, the response depends on the filter structure. Where, each resonator produced different character of a bandpass filter. The dual mode bandpass response for stepped impedance, was achieved by switched ‘OFF’ the PIN diodes, where the insertion loss, S21 4.9 dB, return loss, S11 is below 15 dB, and passband bandwidth is 200 MHz at centre frequency of 2.35 GHz. A good agreement is observed between simulated and measured results. The benefits of this filter is not only can produce a bandpass response, but also high quality factor in bandstop response which offer a better performance and high selectivity. The outcomes of the proposed switchable filters may facilitate improvements and the solution in cognitive radio

Electronically reconfigurable wideband microwave filters

Many systems require multi function capability in the filter aspects of systems; the method currently used is filter banks which take up a lot of board space. It is thought that reconfigurable filters hold the key to replacing filter banks in order to save board space and thus potentially increasing functionality of the systems. The aim of this research is to develop electronically reconfigurable microwave filters for future communication systems. The project investigates some key design issues of reconfigurable filters. Circuits were modelled and full-wave electromagnetic simulations were performed for the investigation. Experimental work was carried out to demonstrate advanced reconfigurable microwave devices. The components used in each concept investigated were pin diodes due to their superior performance in wideband and high frequency applications. Firstly a single coupled line concept was looked at for bandwidth reconfigurability. This concept was then further developed for industrial applications by simply cascading these sections to obtain a high selective filter. A design method was developed for any number of cascades both with and without an impedance transformer; the use of LCP was used to increase flexibility due to its desirable characteristics. The most desirable outcome would be filter to simultaneously control bandwidth and frequency. In order to tackle this issue the coupled line concept was adapted to incorporate frequency tunability, along with a design method being presented. Furthermore, a cascaded highpass/ lowpass filter was also explored for this concept for added flexibility in the design of a filter capable of control of both bandwidth and center frequency

Recent Progress in the Design of 4G/5G Reconfigurable Filters

YesCurrently, several microwave filter designs contend for use in wireless communications. Among various microstrip filter designs, the reconfigurable planar filter presents more advantages and better prospects for communication applications, being compact in size, light-weight and cost-effective. Tuneable microwave filters can reduce the number of switches between electronic components. This paper presents a review of recent reconfigurable microwave filter designs, specifically on current advances in tuneable filters that involve high-quality factor resonator filters to control frequency, bandwidth and selectivity. The most important materials required for this field are also highlighted and surveyed. In addition, the main references for several types of tuneable microstrip filters are reported, especially related to new design technologies. Topics surveyed include microwave and millimetre wave designs for 4G and 5G applications, which use varactors and MEMSs technologies.This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement H2020-MSCA-ITN-2016 SECRET-722424

Filtros sincronizables de banda dual

Una vez centrada la aplicación y el contexto del proyecto es el momento de formular los objetivos de este trabajo. El objetivo principal que engloba todos los demás objetivos de este trabajo es el de demostrar la viabilidad y el diseño de filtros de banda dual reconfigurables. Para su consecución ha sido necesario el planteamiento de toda una serie de objetivos que se enumeran a continuación: El primer objetivo es presentar una metodología de síntesis de filtros de banda dual, que se explicará de forma paralela al diseño de un filtro dual hairpin. Esta metodología tiene que permitir el diseño sistemático de filtros con la herramienta ADS/Momentum a partir del proceso de síntesis teórico explicado en [15]. El segundo objetivo es experimentar con distintos tipos de resonadores planares, en el sentido de evaluar su capacidad para ser modificados con el objetivo que sean sintonizables en frecuencia, y la posibilidad de integrarlos en distintas topologías de filtros. Se han estudiado y modificado convenientemente los resonadores de media longitud de onda y sección constante y el resonador SIR y el resonador OLRR. El tercer objetivo es el diseño, fabricación y medida de distintos filtros de banda dual y reconfigurables, basados con los resonadores anteriores, con el fin de demostrar la viabilidad del concepto propuesto en este trabajo. Finalmente, como objetivo último de este trabajo, se propone el diseño de un filtro de banda dual reconfigurable para aplicaciones WLAN, es decir, que la primera banda esté centrada en 2.45GHz mientras que la segunda banda se pueda sintonizar fácilmente de 5.75GHz a 5.25GHz

Miniaturized High-Q Tunable RF Filters

This dissertation focuses on the investigation and development of novel efficient tuning techniques and the design of miniaturized high-Q tunable RF filters for high-performance reconfigurable systems and applications. First, a detailed survey of the available tuning concepts and state-of-art tunable filters is provided. Then, a novel so-called inset resonator configuration is presented for the applications of fixed and tunable coaxial filters. The design procedure of frequency tunable filters with constant absolute bandwidth (CABW) is described, and various tunable inset filters are implemented, offering many desirable merits, including the wide tuning range and stable high-Q with minimum variation. For wide octave frequency tuning ranges with CABW, a second novel concept is presented using so-called re-entrant caps tuners. Beside simplicity and compactness, this technique also features enhanced spurious performance and wider tuning capabilities than the conventional means. Also, in this dissertation, various miniaturized reconfigurable dual-band/dual-mode bandpass filters and diplexers are presented using compact dual-mode high-Q TM-mode dielectric resonators. Furthermore, a novel microfluidic-based ultra-wide frequency tuning technique for TM010-mode dielectric resonators and filters is introduced in this dissertation. In addition to the very wide tuning window, this mechanism has key advantages of low-cost, simplicity, and intrinsic switch-off. Lastly, the dissertation includes a novel bandwidth reconfiguration concept with multi-octave tuning using a single element for coaxial bandpass filters. This mechanism brings many features including the fast tuning, constant high-Q, intrinsic switch-off, and wide BW-reconfiguration