Thermodynamic Conditions in Quenching Chamber of Low Voltage Circuit Breaker

Práce se zabývá studiem procesů probíhajících při zhášení silnoproudého oblouku ve zhášecí komoře jističe. Je zaměřena na výpočet dynamiky tekutin a teplotního pole v okolí elektrického oblouku. V práci je dále popsán vliv vzdálenosti plechů v komoře a vliv tvarů plechů z hlediska aerodynamických podmínek uvnitř komory. Dalším cílem dosaženým touto prací je poskytnutí informací o vlivu polohy elektrického oblouku na termodynamické vlastnosti uvnitř komory. Toto je důležité, zejména pokud je oblouk do komory vtahován jinými silami, např. elektromagnetickými a během tohoto vtahovacího procesu mění svůj tvar i polohu. Za účelem co nejjednoduššího, ale zároveň co nejefektivnějšího řešení úkolu, byl vyvinut software určen speciálně pro výpočet dynamiky tekutin numerickou metodou konečných objemů (FVM). Tato metoda je, v porovnání s rozšířenější metodou konečných prvků (FEM), vhodnější pro výpočet dynamiky tekutin (CFD) zejména proto, že režie na výpočet jedné iterace jsou menší v porovnání s ostatními numerickými metodami. Další výhodou tohoto softwarového řešení je jeho modularita a rozšiřitelnost. Cely koncept softwaru je postaven na tzv. zásuvných modulech. Díky tomuto řešení můžeme využít výpočtové jádro pro další numerické analýzy, např. strukturální, elektromagnetickou apod. Jediná potřeba pro úspěšné používání těchto analýz je napsáni solveru pro konečné prvky (FEM). Jelikož je software koncipován jako multi–thread aplikace, využívá výkon současných vícejádrových procesorů naplno. Tato vlastnost se ještě více projeví, pokud se výpočet přesune z CPU na GPU. Jelikož současné grafické karty vyšších tříd mají několik desítek až stovek výpočetních jader a pracují s mnohem rychlejšími pamětmi, než CPU, je výpočetní výkon několikanásobně vyšší.Work deals with the study of processes that attend the electric arc extinction inside the quenching chamber of a circuit breaker. It is focused on several areas. The first one is concerned to fluid dynamics calculations (CFD) and the second one is aimed at thermal field calculations. In this work effects of metal plates distance together with metal plates shapes are described from aerodynamical point of view. Another objective solved by this work is to give information about influence of an electric arc position in a quenching chamber, which changed its shape due to forces acting on it during extinction process. For purpose of this work a new software solution for CFD was developed. Whole software concept is based on plug-ins. Due to this solution, the software§s calculation core can be used for other numerical analyses, like structural, electromagnetic, etc. The only requirement is to write a plug-in for these analyses. Because the software is designed as multi-threaded application, it can use the fully performance of current multi-core processors. Above mentioned property can be especially shown off, when a calculation is moved from CPU to GPU (Graphics Processing Units). Current high-end graphic cards have tens to hundreds cores and work with faster memories than CPU. Due to this fact, the simulation performance can raised manifold.

Novel method for the measurement of liquid film thickness during fuel spray impingement on surfaces

This paper describes the development and application of a novel optical technique for the measurement of liquid film thickness formed on surfaces during the impingement of automotive fuel sprays. The technique makes use of the change of the light scattering characteristics of a metal surface with known roughness, when liquid is deposited. Important advantages of the technique over previously established methods are the ability to measure the time-dependent spatial distribution of the liquid film without a need to add a fluorescent tracer to the liquid, while the measurement principle is not influenced by changes of the pressure and temperature of the liquid or the surrounding gas phase. Also, there is no need for non-fluorescing surrogate fuels. However, an in situ calibration of the dependence of signal intensity on liquid film thickness is required. The developed method can be applied to measure the time-dependent and two-dimensional distribution of the liquid fuel film thickness on the piston or the liner of gasoline direct injection (GDI) engines. The applicability of this technique was evaluated with impinging sprays of several linear alkanes and alcohols with different thermo-physical properties. The surface temperature of the impingement plate was controlled to simulate the range of piston surface temperatures inside a GDI engine. Two sets of liquid film thickness measurements were obtained. During the first set, the surface temperature of the plate was kept constant, while the spray of different fuels interacted with the surface. In the second set, the plate temperature was adjusted to match the boiling temperature of each fuel. In this way, the influence of the surface temperature on the liquid film created by the spray of different fuels and their evaporation characteristics could be demonstrated

Index to NASA Tech Briefs, 1975

This index contains abstracts and four indexes--subject, personal author, originating Center, and Tech Brief number--for 1975 Tech Briefs

The benefit of high-conductivity materials in film cooled turbine nozzles

This study presents an experimental and numerical investigation of the beneficial effect of higher conductivity materials in HP turbine nozzles. Most of the literature studies focus on the maximum temperature that a nozzle can withstand, whereas the effect of thermal gradients is often neglected. However thermal gradients have higher influence on the life of the components and they have to be given careful consideration. In this work it is shown that thermal gradients are reduced by using high conductivity materials and, as a consequence, the nozzles life is appreciably increased. A representative film cooled leading edge with an internal impingement plate was studied experimentally at Texas AM University. Two materials were used, namely polycarbonate and stainless steel, in order to highlight the impact of conduction on coolant effectiveness. Numerically conjugate heat transfer simulations have been carried out with an in house solver to analyse in detail the impact of conduction and internal convection. Both experimental and numerical results show that by increasing the conductivity in the solid region, the thermal gradients are strongly reduced. Numerically it is shown that using inserts of nickel-aluminide alloys in nozzles may reduce the thermal gradients from 3 to 4 times if compared to nowadays design. © 2012 Elsevier Inc

Experiment and theory in the Casimir effect

Casimir effect is the attractive force which acts between two plane parallel, closely spaced, uncharged, metallic plates in vacuum. This phenomenon was predicted theoretically in 1948 and reliably investigated experimentally only in recent years. In fact, the Casimir force is similar to the familiar van der Waals force in the case of relatively large separations when the relativistic effects come into play. We review the most important experiments on measuring the Casimir force by means of torsion pendulum, atomic force microscope and micromechanical torsional oscillator. Special attention is paid to the puzzle of the thermal Casimir force, i.e., to the apparent violation of the third law of thermodynamics when the Lifshitz theory of dispersion forces is applied to real metals. Thereafter we discuss the role of the Casimir force in nanosystems including the stiction phenomenon, actuators, and interaction of hydrogen atoms with carbon nanotubes. The applications of the Casimir effect for constraining predictions of extra-dimensional unification schemes and other physics beyond the standard model are also considered.Comment: 11 pages, 14 figure

Generation of high-resolution surface temperature distributions

We have performed numerical calculations to study the generation of arbitrary temperature profiles with high spatial resolution on the surface of a solid. The characteristics of steady-state distributions and time-dependent heating and cooling cycles are examined, as well as their dependence on material properties and device geometry. Ideally, low-power consumption and fast response times are desirable. The simulations show that the achievable spatial resolution is on the order of the substrate thickness and that the response time t+ depends on the width of the individual heating elements. Moreover, the rise time t+ can be significantly shortened by deposition of a thermal insulation layer, which also reduces the power consumption and increases lateral resolution

Rapid Prototyping of PEM Fuel Cell Bi-Polar Plates using 3D Printing and Thermal Spray Deposition

This article presents the results of exploratory research on novel methods for the fabrication of functional, metallic, gas flow, bi polar plates (BPP) for use in proton exchange membrane fuel cells (PEMFC). Low cost, high speed, additive manufacturing methods that combine 3D printing (3DP) and thermal spray (TS) technologies are described. Functional flow plates were manufactured by creating 3DP patterns and then depositing, and releasing, dense metals with TS methods. The new method yields dense metal plates, with interesting options for material choices and complex designs.Mechanical Engineerin

High temperature thermocouple and heat flux gauge using a unique thin film-hardware hot juncture

A special thin film-hardware material thermocouple (TC) and heat flux gauge concept for a reasonably high temperature and high flux flat plate heat transfer experiment was fabricated and tested to gauge temperatures of 911 K. This concept was developed for minimal disturbance of boundary layer temperature and flow over the plates and minimal disturbance of heat flux through the plates. Comparison of special heat flux gauge Stanton number output at steady-state conditions with benchmark literature data was good and agreement was within a calculated uncertainty of the measurement system. Also, good agreement of special TC and standard TC outputs was obtained and the results are encouraging. Oxidation of thin film thermoelements was a primary failure mode after about 5 of operation