DFT and BIST of a multichip module for high-energy physics experiments

Engineers at Politecnico di Torino designed a multichip module for high-energy physics experiments conducted on the Large Hadron Collider. An array of these MCMs handles multichannel data acquisition and signal processing. Testing the MCM from board to die level required a combination of DFT strategie

From FPGA to ASIC: A RISC-V processor experience

This work document a correct design flow using these tools in the Lagarto RISC- V Processor and the RTL design considerations that must be taken into account, to move from a design for FPGA to design for ASIC

Testability considerations for implementing an embedded memory subsystem

textThere are a number of testability considerations for VLSI design, but test coverage, test time, accuracy of test patterns and correctness of design information for DFD (Design for debug) are the most important ones in design with embedded memories. The goal of DFT (Design-for-Test) is to achieve zero defects. When it comes to the memory subsystem in SOCs (system on chips), many flavors of memory BIST (built-in self test) are able to get high test coverage in a memory, but often, no proper attention is given to the memory interface logic (shadow logic). Functional testing and BIST are the most prevalent tests for this logic, but functional testing is impractical for complicated SOC designs. As a result, industry has widely used at-speed scan testing to detect delay induced defects. Compared with functional testing, scan-based testing for delay faults reduces overall pattern generation complexity and cost by enhancing both controllability and observability of flip-flops. However, without proper modeling of memory, Xs are generated from memories. Also, when the design has chip compression logic, the number of ATPG patterns is increased significantly due to Xs from memories. In this dissertation, a register based testing method and X prevention logic are presented to tackle these problems. An important design stage for scan based testing with memory subsystems is the step to create a gate level model and verify with this model. The flow needs to provide a robust ATPG netlist model. Most industry standard CAD tools used to analyze fault coverage and generate test vectors require gate level models. However, custom embedded memories are typically designed using a transistor-level flow, there is a need for an abstraction step to generate the gate models, which must be equivalent to the actual design (transistor level). The contribution of the research is a framework to verify that the gate level representation of custom designs is equivalent to the transistor-level design. Compared to basic stuck-at fault testing, the number of patterns for at-speed testing is much larger than for basic stuck-at fault testing. So reducing test and data volume are important. In this desertion, a new scan reordering method is introduced to reduce test data with an optimal routing solution. With in depth understanding of embedded memories and flows developed during the study of custom memory DFT, a custom embedded memory Bit Mapping method using a symbolic simulator is presented in the last chapter to achieve high yield for memories.Electrical and Computer Engineerin

Design and debugging of multi-step analog to digital converters

With the fast advancement of CMOS fabrication technology, more and more signal-processing functions are implemented in the digital domain for a lower cost, lower power consumption, higher yield, and higher re-configurability. The trend of increasing integration level for integrated circuits has forced the A/D converter interface to reside on the same silicon in complex mixed-signal ICs containing mostly digital blocks for DSP and control. However, specifications of the converters in various applications emphasize high dynamic range and low spurious spectral performance. It is nontrivial to achieve this level of linearity in a monolithic environment where post-fabrication component trimming or calibration is cumbersome to implement for certain applications or/and for cost and manufacturability reasons. Additionally, as CMOS integrated circuits are accomplishing unprecedented integration levels, potential problems associated with device scaling – the short-channel effects – are also looming large as technology strides into the deep-submicron regime. The A/D conversion process involves sampling the applied analog input signal and quantizing it to its digital representation by comparing it to reference voltages before further signal processing in subsequent digital systems. Depending on how these functions are combined, different A/D converter architectures can be implemented with different requirements on each function. Practical realizations show the trend that to a first order, converter power is directly proportional to sampling rate. However, power dissipation required becomes nonlinear as the speed capabilities of a process technology are pushed to the limit. Pipeline and two-step/multi-step converters tend to be the most efficient at achieving a given resolution and sampling rate specification. This thesis is in a sense unique work as it covers the whole spectrum of design, test, debugging and calibration of multi-step A/D converters; it incorporates development of circuit techniques and algorithms to enhance the resolution and attainable sample rate of an A/D converter and to enhance testing and debugging potential to detect errors dynamically, to isolate and confine faults, and to recover and compensate for the errors continuously. The power proficiency for high resolution of multi-step converter by combining parallelism and calibration and exploiting low-voltage circuit techniques is demonstrated with a 1.8 V, 12-bit, 80 MS/s, 100 mW analog to-digital converter fabricated in five-metal layers 0.18-µm CMOS process. Lower power supply voltages significantly reduce noise margins and increase variations in process, device and design parameters. Consequently, it is steadily more difficult to control the fabrication process precisely enough to maintain uniformity. Microscopic particles present in the manufacturing environment and slight variations in the parameters of manufacturing steps can all lead to the geometrical and electrical properties of an IC to deviate from those generated at the end of the design process. Those defects can cause various types of malfunctioning, depending on the IC topology and the nature of the defect. To relive the burden placed on IC design and manufacturing originated with ever-increasing costs associated with testing and debugging of complex mixed-signal electronic systems, several circuit techniques and algorithms are developed and incorporated in proposed ATPG, DfT and BIST methodologies. Process variation cannot be solved by improving manufacturing tolerances; variability must be reduced by new device technology or managed by design in order for scaling to continue. Similarly, within-die performance variation also imposes new challenges for test methods. With the use of dedicated sensors, which exploit knowledge of the circuit structure and the specific defect mechanisms, the method described in this thesis facilitates early and fast identification of excessive process parameter variation effects. The expectation-maximization algorithm makes the estimation problem more tractable and also yields good estimates of the parameters for small sample sizes. To allow the test guidance with the information obtained through monitoring process variations implemented adjusted support vector machine classifier simultaneously minimize the empirical classification error and maximize the geometric margin. On a positive note, the use of digital enhancing calibration techniques reduces the need for expensive technologies with special fabrication steps. Indeed, the extra cost of digital processing is normally affordable as the use of submicron mixed signal technologies allows for efficient usage of silicon area even for relatively complex algorithms. Employed adaptive filtering algorithm for error estimation offers the small number of operations per iteration and does not require correlation function calculation nor matrix inversions. The presented foreground calibration algorithm does not need any dedicated test signal and does not require a part of the conversion time. It works continuously and with every signal applied to the A/D converter. The feasibility of the method for on-line and off-line debugging and calibration has been verified by experimental measurements from the silicon prototype fabricated in standard single poly, six metal 0.09-µm CMOS process

Delay test for diagnosis of power switches

Power switches are used as part of power-gating technique to reduce leakage power of a design. To the best of our knowledge, this is the first work in open-literature to show a systematic diagnosis method for accurately diagnosingpower switches. The proposed diagnosis method utilizes recently proposed DFT solution for efficient testing of power switches in the presence of PVT variation. It divides power switches into segments such that any faulty power switch is detectable thereby achieving high diagnosis accuracy. The proposed diagnosis method has been validated through SPICE simulation using a number of ISCAS benchmarks synthesized with a 90-nm gate library. Simulation results show that when considering the influence of process variation, the worst case loss of accuracy is less than 4.5%; and the worst case loss of accuracy is less than 12% when considering VT (Voltage and Temperature) variations

The Design of a Debugger Unit for a RISC Processor Core

Recently, there has been a significant increase in design complexity for Embedded Systems often referred to as Hardware Software Co-Design. Complexity in design is due to both hardware and firmware closely coupled together in-order to achieve features for low power, high performance and low area. Due to these demands, embedded systems consist of multiple interconnected hardware IPs with complex firmware algorithms running on the device. Often such designs are available in bare-metal form, i.e without an Operating System, which results in difficulty while debugging due to lack of insight into the system. As a result, development cycle and time to market are increased. One of the major challenges for bare-metal design is to capture internal data required during debugging or testing in the post silicon validation stage effectively and efficiently. Post-silicon validation can be performed by leveraging on different technologies such as hardware software co-verification using hardware accelerators, FPGA emulation, logic analyzers, and so on which reduces the complete development cycle time. This requires the hardware to be instrumented with certain features which support debugging capabilities. As there is no standard for debugging capabilities and debugging infrastructure, it completely depends on the manufacturer to manufacturer or designer to designer. This work aims to implement minimum required features for debugging a bare-metal core by instrumenting the hardware compatible for debugging. It takes into consideration the fact that for a single core bare-metal embedded systems silicon area is also a constraint and there must be a trade-off between debugging capabilities which can be implemented in hardware and portions handled in software. The paper discusses various debugging approaches developed and implemented on various processor platforms and implements a new debugging infrastructure by instrumenting the Open-source AMBER 25 core with a set of debug features such as breakpoints, current state read, trace and memory access. Interface between hardware system and host system is designed using a JTAG standard TAP controller. The resulting design can be used in debugging and testing during post silicon verification and validation stages. The design is synthesized using Synopsys Design Compiler targeting a 65 nm technology node and results are compared for the instrumented and non-instrumented system

Analysis and optimization of a debug post-silicon hardware architecture

The goal of this thesis is to analyze the post-silicon validation hardware infrastructure implemented on multicore systems taking as an example Esperanto Technologies SoC, which has thousands of RISC-V processors and targets specific software applications. Then, based on the conclusions of the analysis, the project proposes a new post-silicon debug architecture that can fit on any System on-Chip without depending on its target application or complexity and that optimizes the options available on the market for multicore systems