A High-Gain Observer-Based Adaptive Super-Twisting Algorithm for DC-Link Voltage Control of NPC Converters

Acting as an interface between the grid and many energy systems, the active front-end (AFE) has been widely used in a large variety of industrial applications. In this paper, in order to ensure the fast dynamic performance and good disturbance rejection ability of the AFE, a high-gain observer (HGO) plus adaptive super-twisting algorithm (STA) for the three-level neutral-point-clamped (NPC) converter is proposed. Comparing with the conventional PI control strategy, the proposed controller implements the adaptive STA in the voltage regulator to provide a faster transient response. The gains of the adaptive STA keep varying according to the rules being reduced in steady state but increasing in transient conditions. Therefore, the chattering phenomenon is mitigated and the dynamic response is guaranteed. Additionally, to undermine the impact of external disturbances on the dc-link voltage, a high-efficiency HGO is designed in the voltage regulation loop to reject it. Experimental results based on a three-level NPC prototype are given and compared with the conventional PI method to validate the fast dynamic performance and high disturbance rejection ability of the proposed approach.National Key R&D Program of China SQ2019YFB130028National Natural Science Foundation of China 61525303National Natural Science Foundation of China 41772377National Natural Science Foundation of China 61673130Self-Planned Task of State Key Laboratory of Robotics and System (HIT) SKLRS201806BMinisterio de Economía y Competitividad TEC2016-78430-RJunta de Andalucía P18-RT-1340Fondo de Investigación Nacional de Qatar NPRP 9-310-2-13

Extended State Observer-Based Sliding-Mode Control for Three-Phase Power Converters

This paper proposes an extended state observer (ESO) based second-order sliding-mode (SOSM) control for three-phase two-level grid-connected power converters. The proposed control technique forces the input currents to track the desired values, which can indirectly regulate the output voltage while achieving a user-defined power factor. The presented approach has two control loops. A current control loop based on an SOSM and a dc-link voltage regulation loop which consists of an ESO plus SOSM. In this work, the load connected to the dc-link capacitor is considered as an external disturbance. An ESO is used to asymptotically reject this external disturbance. Therefore, its design is considered in the control law derivation to achieve a high performance. Theoretical analysis is given to show the closed-loop behavior of the proposed controller and experimental results are presented to validate the control algorithm under a real power converter prototyp

Design and Advanced Model Predictive Control of Wide Bandgap Based Power Converters

The field of power electronics (PE) is experiencing a revolution by harnessing the superior technical characteristics of wide-band gap (WBG) materials, namely Silicone Carbide (SiC) and Gallium Nitride (GaN). Semiconductor devices devised using WBG materials enable high temperature operation at reduced footprint, offer higher blocking voltages, and operate at much higher switching frequencies compared to conventional Silicon (Si) based counterpart. These characteristics are highly desirable as they allow converter designs for challenging applications such as more-electric-aircraft (MEA), electric vehicle (EV) power train, and the like. This dissertation presents designs of a WBG based power converters for a 1 MW, 1 MHz ultra-fast offboard EV charger, and 250 kW integrated modular motor drive (IMMD) for a MEA application. The goal of these designs is to demonstrate the superior power density and efficiency that are achievable by leveraging the power of SiC and GaN semiconductors. Ultra-fast EV charging is expected to alleviate the challenge of range anxiety , which is currently hindering the mass adoption of EVs in automotive market. The power converter design presented in the dissertation utilizes SiC MOSFETs embedded in a topology that is a modification of the conventional three-level (3L) active neutral-point clamped (ANPC) converter. A novel phase-shifted modulation scheme presented alongside the design allows converter operation at switching frequency of 1 MHz, thereby miniaturizing the grid-side filter to enhance the power density. IMMDs combine the power electronic drive and the electric machine into a single unit, and thus is an efficient solution to realize the electrification of aircraft. The IMMD design presented in the dissertation uses GaN devices embedded in a stacked modular full-bridge converter topology to individually drive each of the motor coils. Various issues and solutions, pertaining to paralleling of GaN devices to meet the high current requirements are also addressed in the thesis. Experimental prototypes of the SiC ultra-fast EV charger and GaN IMMD were built, and the results confirm the efficacy of the proposed designs. Model predictive control (MPC) is a nonlinear control technique that has been widely investigated for various power electronic applications in the past decade. MPC exploits the discrete nature of power converters to make control decisions using a cost function. The controller offers various advantages over, e.g., linear PI controllers in terms of fast dynamic response, identical performance at a reduced switching frequency, and ease of applicability to MIMO applications. This dissertation also investigates MPC for key power electronic applications, such as, grid-tied VSC with an LCL filter and multilevel VSI with an LC filter. By implementing high performance MPC controllers on WBG based power converters, it is possible to formulate designs capable of fast dynamic tracking, high power operation at reduced THD, and increased power density

A Reduced-Order Generalized Proportional Integral Observer-Based Resonant Super-Twisting Sliding Mode Control for Grid-Connected Power Converters

This article presents a reduced-order generalized proportional-integral observer based resonant super-twisting sliding mode controller (RST-SMC) for the three-phase ac-dc converters. On the contrary to utilizing the proportional-integral controller in regulating the dc-link voltage, which may cause large undershoot/overshoot under the disturbance, the proposed voltage control strategy for the dc-link has high disturbance rejection ability and the settling time has been greatly reduced. In addition, the proposed RST-SMC in the current control loop not only preserve the merits of the sliding mode controller but also achieve the current tracking without steady-state error in the stationary \alpha - \beta frame. The effectiveness of the proposed method has been verified by a lab-constructed experimental prototype.This work was supported by Shenzhen Overseas High Level Talent Program. The work of Josep M. Guerrerork was supported by VILLUM FONDEN under the VILLUM Investigator Grant (no. 25920): Center for Research on Microgrids (CROM); www.crom.et.aau.dk

Control of power converter in modern power systems

A la portada consta el nom del programa interuniversitari: Joint Doctoral Programme in Electric Energy Systems [by the] Universidad de Málaga, Universidad de Sevilla, Universidad del País Vasco/Euskal Erriko Unibertsitatea i Universitat Politècnica de CatalunyaPower system is undergoing an unpreceded paradigm shift: from centralized to distributed generation. As the renewable-based generations and battery storage systems are increasingly displacing conventional generations, it becomes more and. more difficult to maintain the stability and reliability of the grid by using only conventional generations. The main reason for the degradation of grid stability is the rapid penetration of nonconventional sources. These new generations interface with the grids through power electronics converters which are conventionally designed to maximize conversion efficiency and resource utilization. Indeed, these power converters only focus on their internal operation despite the grid conditions, which often worsens the grid operation. To overcome such a drawback, the grid-forming concept has been proposed for power converters, aiming to redesign the control of the power converters to enforce more grid-friendly behaviours such as inertia response and power oscillation damping to name a few. Despite the rich literature, actual adaptation of grid-forming controller in real-world applications is still rare because incentives for renewable power plants to provide services based on such advanced grid-forming functions were at best scarce. In the last years, however, several system operators have imposed new requirements and markets for grid-supporting services. In addition, the existing grid-forming controllers require modification to low-level control firmware of a power converter, which is often unrealistic due to the control hardware limitations as well as necessary testing and certifications. To ensure a stable operation of a grid-forming converter under adverse operating conditions, a robust voltage sensorless current controller is developed in this PhD thesis. The proposed controller is able to handle most of the possible abnormal conditions of the grid such as impedance variations, unbalanced voltage; harmonics distortion. These abnormalities of the grid are mathematically represented using equivalent linear models such that they can be used for calculating the controller gains. Linear matrix inequality techniques are also used to facilitate parameter tuning. In fact, the performance and stability of the current control loop can be determined through only two tuning parameters instead of eight parameters for a controller of a similar structure. The existing grid-forming implementations are designed considering that the control firmware of the power converter can be upgraded at will. However, modifications of the control firmware are not straightforward and cost-effective at mass scale. To overcome such a limitation, an external synchronous controller is presented in this PhD thesis. The external synchronous controller uses measurements, which are either provided by the power converter or a dedicated measurement unit, to calculate the actual active and reactive power that should be injected by the power converters in a way that the power plant acts as an aggregated grid­forming converter. As a result, any conventional power converters can be utilized for providing grid-supporting services with minimal modification to the existing infrastructure. Power converters can provide even better performance than a synchronous generator if a proper control scheme is used. In this regard, the final chapter of this PhD thesis presents the multi-rotor virtual machine implementation for grid-forming converter to boost their damping performance to power oscillations. The multi-rotor virtual machine-controller implements several virtual rotors instead of only one rotor as in typical grid-forming strategies. Since each of the virtual rotors is tuned to target a specific critical mode, the damping participation to such a mode can be increased and adjusted individually. The controllers presented in this PhD thesis are validated through simulators and experiments in the framework of the H2020 FlexiTranstore project. The results are throughout analysed to assess the control performance as well as to highlight possible implications.A medida que las generaciones basadas en energías renovables y los sistemas de almacenamiento de baterías desplazan la generación convencional, se vuelve cada vez más difícil mantener la estabilidad y confiabilidad de la red. Estas nuevas generaciones interactúan con las redes a través de convertidores de electrónica de potencia que están diseñados tradicionalmente para maximizar la eficiencia de conversión y la utilización de recursos. Estos convertidores centran su funcionamiento interno independientemente de las condiciones de la red, lo que a menudo empeora el funcionamiento de la red. Para esto, se ha propuesto el concepto de convertidores de potencia formadores de red (grid-forming), con el objetivo de rediseñar el control de los convertidores de potencia para imponer comportamientos más favorables a la red, por ejemplo, la respuesta inercial y la amortiguación de oscilaciones de potencia. No en tanto, la adaptación real del controlador grid-forming en aplicaciones del mundo real todavía es escasa debido a los pocos incentivos para que las plantas de energía renovable proporcionen servicios basados en funciones de formación de red tan avanzadas. Aunque en los últimos años, operadores de sistemas han impuesto nuevos requisitos y mercados para servicios auxiliares, los controladores grid-forming existentes requieren cambios en el firmware de control de bajo nivel de un convertidor de potencia, algo poco realista debido a las limitaciones del hardware de control, así como a las pruebas y certificaciones necesarias. En esta tesis se desarrolla un controlador de corriente robusto, sin sensor de tensión, para garantizar el funcionamiento estable de un convertidor grid-forming en condiciones de operación adversas. Este controlador es capaz de manejar la mayoría de las condiciones anormales de red, como variaciones de impedancia, tensión desequilibrada y distorsión de armónicos. Estas anomalías de la red se representan matemáticamente mediante modelos lineales equivalentes, utilizados para calcular las ganancias del controlador. También, usando técnicas de desigualdad matricial lineal para facilitar el ajuste de parámetros. De hecho, el rendimiento y la estabilidad del bucle de control de la corriente pueden determinarse mediante sólo dos parámetros de sintonización. Las implementaciones de formación de red existentes están diseñadas considerando que el firmware de control del convertidor de potencia puede actualizarse a voluntad. Sin embargo, las modificaciones del firmware de control no son sencillas ni rentables a gran escala. Por tanto, esta tesis presenta un controlador síncrono externo que utiliza las mediciones proporcionadas por el convertidor de potencia o por una unidad de medición dedicada para calcular la potencia activa y reactiva real que deben inyectar los convertidores de potencia, de forma que la central eléctrica actúe como un convertidor grid-forming agregado. Como resultado, cualquier convertidor de potencia convencional puede utilizarse para proporcionar servicios de apoyo a la red con una modificación mínima de la infraestructura existente. Los convertidores de potencia pueden ofrecer mejor rendimiento que un generador síncrono utilizando un esquema de control adecuado. El último capítulo de esta tesis presenta la implementación de una máquina virtual multirrotor para que los convertidores de red aumenten su rendimiento de amortiguación de las oscilaciones de potencia. El controlador de la máquina virtual multirrotor implementa varios rotores virtuales en lugar de un solo rotor como en las estrategias típicas de grid-forming. Dado que cada uno de los rotores virtuales está sintonizado para dirigirse a un modo crítico específico, la participación de la amortiguación a dicho modo puede aumentarse y ajustarse individualmente. Los controladores presentados en esta tesis doctoral han sido validados mediante simulaciones y experimentos en el marco del proyecto H2020 FlexiTranstore.Postprint (published version

Control and Stability of Residential Microgrid with Grid-Forming Prosumers

The rise of the prosumers (producers-consumers), residential customers equipped with behind-the-meter distributed energy resources (DER), such as battery storage and rooftop solar PV, offers an opportunity to use prosumer-owned DER innovatively. The thesis rests on the premise that prosumers equipped with grid-forming inverters can not only provide inertia to improve the frequency performance of the bulk grid but also support islanded operation of residential microgrids (low-voltage distribution feeder operated in an islanded mode), which can improve distribution grids’ resilience and reliability without purposely designing low-voltage (LV) distribution feeders as microgrids. Today, grid-following control is predominantly used to control prosumer DER, by which the prosumers behave as controlled current sources. These grid-following prosumers deliver active and reactive power by staying synchronized with the existing grid. However, they cannot operate if disconnected from the main grid due to the lack of voltage reference. This gives rise to the increasing interest in the use of grid-forming power converters, by which the prosumers behave as voltage sources. Grid-forming converters regulate their output voltage according to the reference of their own and exhibit load sharing with other prosumers even in islanded operation. Making use of grid-forming prosumers opens up opportunities to improve distribution grids’ resilience and enhance the genuine inertia of highly renewable-penetrated power systems. Firstly, electricity networks in many regional communities are prone to frequent power outages. Instead of purposely designing the community as a microgrid with dedicated grid-forming equipment, the LV feeder can be turned into a residential microgrid with multiple paralleled grid-forming prosumers. In this case, the LV feeder can operate in both grid-connected and islanded modes. Secondly, gridforming prosumers in the residential microgrid behave as voltage sources that respond naturally to the varying loads in the system. This is much like synchronous machines extracting kinetic energy from rotating masses. “Genuine” system inertia is thus enhanced, which is fundamentally different from the “emulated” inertia by fast frequency response (FFR) from grid-following converters. Against this backdrop, this thesis mainly focuses on two aspects. The first is the small-signal stability of such residential microgrids. In particular, the impact of the increasing number of grid-forming prosumers is studied based on the linearised model. The impact of the various dynamic response of primary sources is also investigated. The second is the control of the grid-forming prosumers aiming to provide sufficient inertia for the system. The control is focused on both the inverters and the DC-stage converters. Specifically, the thesis proposes an advanced controller for the DC-stage converters based on active disturbance rejection control (ADRC), which observes and rejects the “total disturbance” of the system, thereby enhancing the inertial response provided by prosumer DER. In addition, to make better use of the energy from prosumer-owned DER, an adaptive droop controller based on a piecewise power function is proposed, which ensures that residential ESS provide little power in the steady state while supplying sufficient power to cater for the demand variation during the transient state. Proposed strategies are verified by time-domain simulations

Prädiktive Regelung und Finite-Set-Beobachter für Windgeneratoren mit variabler Drehgeschwindigkeit

This dissertation presents several model predictive control (MPC) techniques and finite-position-set observers (FPSOs) for permanent-magnet synchronous generators and doubly-fed induction generators in variable-speed wind turbines. The proposed FPSOs are novel ones and based on the concept of finite-control-set MPC. Then, the problems of the MPC techniques like sensitivity to variations of the model parameters and others are investigated and solved in this work.Die vorliegende Dissertation stellt mehrere unterschiedliche Verfahren der modellprädiktiven Regelung (MPC) und so genannte Finite-Position-Set-Beobachter (FPSO) sowohl für Synchrongeneratoren mit Permanentmagneterregung als auch für doppelt gespeiste Asynchrongeneratoren in Windkraftanlagen mit variabler Drehzahl vor und untersucht diese. Für die Beobachter (FPSO) wird ein neuartiger Ansatz vorgestellt, der auf dem Konzept der Finite-Control-Set-MPC basiert. Außerdem werden typische Eigenschaften der MPC wie beispielsweise die Anfälligkeit gegenüber Parameterschwankungen untersucht und kompensiert