A battery-less, self-sustaining RF energy harvesting circuit with TFETs for µW power applications

This paper proposes a Tunnel FET (TFET) power management circuit for RF energy harvesting applications. In contrast with conventional MOSFET technologies, the improved electrical characteristics of TFETs promise a better behavior in the process of rectification and conversion at ultra-low power (µW) and voltage (sub-0.25 V) levels. RF powered systems can not only benefit from TFETs in front-end rectifiers by harvesting the surrounding energy at levels where conventional technologies cannot operate but also in the minimization of energy required by the power management circuit. In this work we present an energy harvesting circuit for RF sources designed with TFETs. The TFET controller emulates an adequate impedance at the output of the rectifier in order to allow maximum transfer of power from the RF source to the input of the boost converter. The output load is activated once the output capacitor reaches a voltage value of 0.5 V. The results show an efficiency boost of 89 % for an output load consuming 1 µW with an available RF power of -25 dBm.Postprint (published version

Design, Fabrication and Characterization of a Piezoelectric Microgenerator Including a Power Management Circuit

We report in this paper the design, fabrication and experimental characterization of a piezoelectric MEMS microgenerator. This device scavenges the energy of ambient mechanical vibrations characterized by frequencies in the range of 1 kHz. This component is made with Aluminum Nitride thin film deposited with a CMOS compatible process. Moreover we analyze two possible solutions for the signal rectification: a discrete doubler-rectifier and a full custom power management circuit. The ASIC developed for this application takes advantage of diodes with very low threshold voltage and therefore allows the conversion of extremely low input voltages corresponding to very weak input accelerations. The volume of the proposed generator is inferior to 1mm3 and the generated powers are in the range of 1$\mu$W. This system is intended to supply power to autonomous wireless sensor nodes.Comment: Submitted on behalf of EDA Publishing Association (http://irevues.inist.fr/EDA-Publishing

TFET-Based power management circuit for RF energy harvesting

This paper proposes a Tunnel FET (TFET)-based power management circuit (PMC) for ultra-low power RF energy harvesting applications. In contrast with conventional thermionic devices, the band-to-band tunneling mechanism of TFETs allows a better switching performance at sub-0.2 V operation. As a result, improved efficiencies in RF-powered circuits are achieved, thanks to increased rectification performance at low power levels and to the reduced energy required for a proper PMC operation. It is shown by simulations that heterojunction TFET devices designed with III-V materials can improve the rectification process at received power levels below -20 dBm (915 MHz) when compared to the application of homojunction III-V TFETs and Si FinFETs. For an available power of -25 dBm, the proposed converter is able to deliver 1.1 µW of average power (with 0.5 V) to the output load with a boost efficiency of 86%.Postprint (author's final draft

Photovoltaic Energy Harvester with Power Management System

We present a photovoltaic energy harvester, realized in 0.35-μm CMOS technology. The proposed system collects light energy from the environment, by means of 2-mm2on-chip integrated microsolar cells, and accumulates it in an external capacitor. While the capacitor is charging, the load is disconnected. When the energy in the external capacitor is enough to operate the load for a predefined time slot, the load is connected to the capacitor by a power management circuit. The choice of the value of the capacitance determines the operating time slot for the load. The proposed solution is suitable for discrete-time-regime applications, such as sensor network nodes, or, in general, systems that require power supply periodically for short time slots. The power management circuit includes a charge pump, a comparator, a level shifter, and a linear voltage regulator. The whole system has been extensively simulated, integrated, and experimentally characterized

Design of a Power Management Circuit for an Opto-Electro Stimulator

This paper presents the design of an integrated power management circuit for use in an implantable opto-electro stimulator. It features an active rectifier with pulse width modulation (PWM) regulation to generate a 3.3 V regulated output, and a 3-stage high voltage charge pump (CP) that generates a 12 V output from a 3.3 V input with a 20 MHz, two-phase non-overlapping clock generator. The circuits were designed in a 0.18-µm CMOS technology requiring a chip area of 0.048 mm 2 . Simulation results show that the regulating rectifier has a voltage conversion efficiency of 94.3% and 92.8% with an ac input magnitude of 3.5 V and 3.6 V, respectively. The peak power transfer efficiency of the regulated 3.3V output voltage is 70.7% with a maximum output power of 30.3 mW. The CP with an overall on-chip capacitance is 60 pF

Radio Frequency Energy Harvesting

This project aims to come out with a system that able to exert some energy from radio waves that able to use by other electronics equipments. This device consists of three main parts to works which are, Radio Frequency Transducer, Power Management circuit, and the Energy Storage Device

Rectification, amplification and switching capabilities for energy harvesting systems: power management circuit for piezoelectric energy harvester

Dissertação de mestrado em Biomedical EngineeringA new energy mechanism needs to be addressed to overcome the battery dependency, and consequently extend Wireless Sensor Nodes (WSN) lifetime effectively. Energy Harvesting is a promising technology that can fulfill that premise. This work consists of the realization of circuit components employable in a management system for a piezoelectric-based energy harvester, with low power consumption and high efficiency. The implementation of energy harvesting systems is necessary to power-up front-end applications without any battery. The input power and voltage levels generated by the piezoelectric transducer are relatively low, especially in small-scale systems, as such extra care has to be taken in power consumption and efficiency of the circuits. The main contribution of this work is a system capable of amplifying, rectifying and switching the unstable signal from an energy harvester source. The circuit components are designed based on 0.13 Complementary Metal-Oxide-Semiconductor (CMOS) technology. An analog switch, capable of driving the harvesting circuit at a frequency between 1 and 1 , with proper temperature behaviour, is designed and verified. An OFF resistance of 520.6 Ω and isolation of −111.24 , grant excellent isolation to the circuit. The designed voltage amplifier is capable of amplifying a minor signal with a gain of 42.56 , while requiring low power consumption. The output signal is satisfactorily amplified with a reduced offset voltage of 8 . A new architecture of a two-stage active rectifier is proposed. The power conversion efficiency is 40.4%, with a voltage efficiency of up to 90%. Low power consumption of 17.7 is achieved by the rectifier, with the embedded comparator consuming 113.9 . The outcomes validate the circuit’s power demands, which can be used for other similar applications in biomedical, industrial, and commercial fields.Para combater a dependência dos dispositivos eletrónicos relativamente ás baterias é necessário um novo sistema energético, que permita prolongar o tempo de vida útil dos mesmos. Energy Harvesting é uma tecnologia promissora utilizada para alimentar dispositivos sem bateria. Este trabalho consiste na realização de componentes empregáveis num circuito global para extrair energia a partir ds vibrações de um piezoelétricos com baixo consumo de energia e alta eficiência. Os níveis de potência e voltagem gerados pelo transdutor piezoelétrico são relativamente baixos, especialmente em sistemas de pequena escala, por isso requerem cuidado extra relativamente ao consumo de energia e eficiência dos circuitos. A principal contribuição deste trabalho é um sistema apropriado para amplificar, retificar e alternar o sinal instável proveniente de uma fonte de energy harvesting. Os componentes do sistema são implementados com base na tecnologia CMOS com 0.13 . Um interruptor analógico capaz de modelar a frequência do sinal entre 1 e 1 e estável perante variações de temperatura, é implementado. O circuito tem um excelente isolamento de −111.24 , devido a uma resistência OFF de 520.6 Ω. O amplificador implementado é apto a amplificar um pequeno sinal com um ganho de 42.56 e baixo consumo. O sinal de saída é satisfatoriamente amplificado com uma voltagem de offset de 8 . Um retificador ativo de dois estágios com uma nova arquitetura é proposto. A eficiência de conversão de energia atinge os 40.4%, com uma eficiência de voltagem até 90%. O retificador consome pouca energia, apenas 17.7 , incorporando um comparador de 113.9 . Os resultados validam as exigências energéticas do circuito, que pode ser usado para outras aplicações similares no campo biomédico, industrial e comercial

Electrical Characterization of Textile-Based Enzymatic Biofuel Cell for Energy Harvesting Interface Circuit

International audienceThis paper presents electrical characterization and power management circuit of textile-based enzymatic biofuel cell. Firstly, static electrical characteristics (open circuit voltage, short circuit current, and maximum power) of the enzymatic biofuel cell have been investigated by imposing a voltage across the biofuel cell and measuring corresponding output current. Output power of the biofuel cell has been characterized as a function of load resistance, while a glucose solution of 100 mM is fed from one end of the textile-based biofuel cell. Two-step approach based on supercapacitor and DC-DC converter has been proposed and tested as power management of the proposed biofuel cell