Power Efficient Data-Aware SRAM Cell for SRAM-Based FPGA Architecture

The design of low-power SRAM cell becomes a necessity in today\u27s FPGAs, because SRAM is a critical component in FPGA design and consumes a large fraction of the total power. The present chapter provides an overview of various factors responsible for power consumption in FPGA and discusses the design techniques of low-power SRAM-based FPGA at system level, device level, and architecture levels. Finally, the chapter proposes a data-aware dynamic SRAM cell to control the power consumption in the cell. Stack effect has been adopted in the design to reduce the leakage current. The various peripheral circuits like address decoder circuit, write/read enable circuits, and sense amplifier have been modified to implement a power-efficient SRAM-based FPGA

Cross layer reliability estimation for digital systems

Forthcoming manufacturing technologies hold the promise to increase multifuctional computing systems performance and functionality thanks to a remarkable growth of the device integration density. Despite the benefits introduced by this technology improvements, reliability is becoming a key challenge for the semiconductor industry. With transistor size reaching the atomic dimensions, vulnerability to unavoidable fluctuations in the manufacturing process and environmental stress rise dramatically. Failing to meet a reliability requirement may add excessive re-design cost to recover and may have severe consequences on the success of a product. %Worst-case design with large margins to guarantee reliable operation has been employed for long time. However, it is reaching a limit that makes it economically unsustainable due to its performance, area, and power cost. One of the open challenges for future technologies is building ``dependable'' systems on top of unreliable components, which will degrade and even fail during normal lifetime of the chip. Conventional design techniques are highly inefficient. They expend significant amount of energy to tolerate the device unpredictability by adding safety margins to a circuit's operating voltage, clock frequency or charge stored per bit. Unfortunately, the additional cost introduced to compensate unreliability are rapidly becoming unacceptable in today's environment where power consumption is often the limiting factor for integrated circuit performance, and energy efficiency is a top concern. Attention should be payed to tailor techniques to improve the reliability of a system on the basis of its requirements, ending up with cost-effective solutions favoring the success of the product on the market. Cross-layer reliability is one of the most promising approaches to achieve this goal. Cross-layer reliability techniques take into account the interactions between the layers composing a complex system (i.e., technology, hardware and software layers) to implement efficient cross-layer fault mitigation mechanisms. Fault tolerance mechanism are carefully implemented at different layers starting from the technology up to the software layer to carefully optimize the system by exploiting the inner capability of each layer to mask lower level faults. For this purpose, cross-layer reliability design techniques need to be complemented with cross-layer reliability evaluation tools, able to precisely assess the reliability level of a selected design early in the design cycle. Accurate and early reliability estimates would enable the exploration of the system design space and the optimization of multiple constraints such as performance, power consumption, cost and reliability. This Ph.D. thesis is devoted to the development of new methodologies and tools to evaluate and optimize the reliability of complex digital systems during the early design stages. More specifically, techniques addressing hardware accelerators (i.e., FPGAs and GPUs), microprocessors and full systems are discussed. All developed methodologies are presented in conjunction with their application to real-world use cases belonging to different computational domains

GPU NTC Process Variation Compensation with Voltage Stacking

Near-threshold computing (NTC) has the potential to significantly improve efficiency in high throughput architectures, such as general-purpose computing on graphic processing unit (GPGPU). Nevertheless, NTC is more sensitive to process variation (PV) as it complicates power delivery. We propose GPU stacking, a novel method based on voltage stacking, to manage the effects of PV and improve the power delivery simultaneously. To evaluate our methodology, we first explore the design space of GPGPUs in the NTC to find a suitable baseline configuration and then apply GPU stacking to mitigate the effects of PV. When comparing with an equivalent NTC GPGPU without PV management, we achieve 37% more performance on average. When considering high production volume, our approach shifts all the chips closer to the nominal non-PV case, delivering on average (across chips) ˜80 % of the performance of nominal NTC GPGPU, whereas when not using our technique, chips would have ˜50 % of the nominal performance. We also show that our approach can be applied on top of multifrequency domain designs, improving the overall performance

AI/ML Algorithms and Applications in VLSI Design and Technology

An evident challenge ahead for the integrated circuit (IC) industry in the nanometer regime is the investigation and development of methods that can reduce the design complexity ensuing from growing process variations and curtail the turnaround time of chip manufacturing. Conventional methodologies employed for such tasks are largely manual; thus, time-consuming and resource-intensive. In contrast, the unique learning strategies of artificial intelligence (AI) provide numerous exciting automated approaches for handling complex and data-intensive tasks in very-large-scale integration (VLSI) design and testing. Employing AI and machine learning (ML) algorithms in VLSI design and manufacturing reduces the time and effort for understanding and processing the data within and across different abstraction levels via automated learning algorithms. It, in turn, improves the IC yield and reduces the manufacturing turnaround time. This paper thoroughly reviews the AI/ML automated approaches introduced in the past towards VLSI design and manufacturing. Moreover, we discuss the scope of AI/ML applications in the future at various abstraction levels to revolutionize the field of VLSI design, aiming for high-speed, highly intelligent, and efficient implementations

Toward Fault-Tolerant Applications on Reconfigurable Systems-on-Chip

L'abstract è presente nell'allegato / the abstract is in the attachmen

Energy Aware Runtime Systems for Elastic Stream Processing Platforms

Following an invariant growth in the required computational performance of processors, the multicore revolution started around 20 years ago. This revolution was mainly an answer to power dissipation constraints restricting the increase of clock frequency in single-core processors. The multicore revolution not only brought in the challenge of parallel programming, i.e. being able to develop software exploiting the entire capabilities of manycore architectures, but also the challenge of programming heterogeneous platforms. The question of “on which processing element to map a specific computational unit?”, is well known in the embedded community. With the introduction of general-purpose graphics processing units (GPGPUs), digital signal processors (DSPs) along with many-core processors on different system-on-chip platforms, heterogeneous parallel platforms are nowadays widespread over several domains, from consumer devices to media processing platforms for telecom operators. Finding mapping together with a suitable hardware architecture is a process called design-space exploration. This process is very challenging in heterogeneous many-core architectures, which promise to offer benefits in terms of energy efficiency. The main problem is the exponential explosion of space exploration. With the recent trend of increasing levels of heterogeneity in the chip, selecting the parameters to take into account when mapping software to hardware is still an open research topic in the embedded area. For example, the current Linux scheduler has poor performance when mapping tasks to computing elements available in hardware. The only metric considered is CPU workload, which as was shown in recent work does not match true performance demands from the applications. Doing so may produce an incorrect allocation of resources, resulting in a waste of energy. The origin of this research work comes from the observation that these approaches do not provide full support for the dynamic behavior of stream processing applications, especially if these behaviors are established only at runtime. This research will contribute to the general goal of developing energy-efficient solutions to design streaming applications on heterogeneous and parallel hardware platforms. Streaming applications are nowadays widely spread in the software domain. Their distinctive characiteristic is the retrieving of multiple streams of data and the need to process them in real time. The proposed work will develop new approaches to address the challenging problem of efficient runtime coordination of dynamic applications, focusing on energy and performance management.Efter en oföränderlig tillväxt i prestandakrav hos processorer, började den flerkärniga processor-revolutionen för ungefär 20 år sedan. Denna revolution skedde till största del som en lösning till begränsningar i energieffekten allt eftersom klockfrekvensen kontinuerligt höjdes i en-kärniga processorer. Den flerkärniga processor-revolutionen medförde inte enbart utmaningen gällande parallellprogrammering, m.a.o. förmågan att utveckla mjukvara som använder sig av alla delelement i de flerkärniga processorerna, men också utmaningen med programmering av heterogena plattformar. Frågeställningen ”på vilken processorelement skall en viss beräkning utföras?” är väl känt inom ramen för inbyggda datorsystem. Efter introduktionen av grafikprocessorer för allmänna beräkningar (GPGPU), signalprocesserings-processorer (DSP) samt flerkärniga processorer på olika system-on-chip plattformar, är heterogena parallella plattformar idag omfattande inom många domäner, från konsumtionsartiklar till mediaprocesseringsplattformar för telekommunikationsoperatörer. Processen att placera beräkningarna på en passande hårdvaruplattform kallas för utforskning av en designrymd (design-space exploration). Denna process är mycket utmanande för heterogena flerkärniga arkitekturer, och kan medföra fördelar när det gäller energieffektivitet. Det största problemet är att de olika valmöjligheterna i designrymden kan växa exponentiellt. Enligt den nuvarande trenden som förespår ökad heterogeniska aspekter i processorerna är utmaningen att hitta den mest passande placeringen av beräkningarna på hårdvaran ännu en forskningsfråga inom ramen för inbyggda datorsystem. Till exempel, den nuvarande schemaläggaren i Linux operativsystemet är inkapabel att hitta en effektiv placering av beräkningarna på den underliggande hårdvaran. Det enda mätsättet som används är processorns belastning vilket, som visats i tidigare forskning, inte motsvarar den verkliga prestandan i applikationen. Användning av detta mätsätt vid resursallokering resulterar i slöseri med energi. Denna forskning härstammar från observationerna att dessa tillvägagångssätt inte stöder det dynamiska beteendet hos ström-processeringsapplikationer (stream processing applications), speciellt om beteendena bara etableras vid körtid. Denna forskning kontribuerar till det allmänna målet att utveckla energieffektiva lösningar för ström-applikationer (streaming applications) på heterogena flerkärniga hårdvaruplattformar. Ström-applikationer är numera mycket vanliga i mjukvarudomän. Deras distinkta karaktär är inläsning av flertalet dataströmmar, och behov av att processera dem i realtid. Arbetet i denna forskning understöder utvecklingen av nya sätt för att lösa det utmanade problemet att effektivt koordinera dynamiska applikationer i realtid och fokus på energi- och prestandahantering

Radiation Hardened by Design Methodologies for Soft-Error Mitigated Digital Architectures

abstract: Digital architectures for data encryption, processing, clock synthesis, data transfer, etc. are susceptible to radiation induced soft errors due to charge collection in complementary metal oxide semiconductor (CMOS) integrated circuits (ICs). Radiation hardening by design (RHBD) techniques such as double modular redundancy (DMR) and triple modular redundancy (TMR) are used for error detection and correction respectively in such architectures. Multiple node charge collection (MNCC) causes domain crossing errors (DCE) which can render the redundancy ineffectual. This dissertation describes techniques to ensure DCE mitigation with statistical confidence for various designs. Both sequential and combinatorial logic are separated using these custom and computer aided design (CAD) methodologies. Radiation vulnerability and design overhead are studied on VLSI sub-systems including an advanced encryption standard (AES) which is DCE mitigated using module level coarse separation on a 90-nm process with 99.999% DCE mitigation. A radiation hardened microprocessor (HERMES2) is implemented in both 90-nm and 55-nm technologies with an interleaved separation methodology with 99.99% DCE mitigation while achieving 4.9% increased cell density, 28.5 % reduced routing and 5.6% reduced power dissipation over the module fences implementation. A DMR register-file (RF) is implemented in 55 nm process and used in the HERMES2 microprocessor. The RF array custom design and the decoders APR designed are explored with a focus on design cycle time. Quality of results (QOR) is studied from power, performance, area and reliability (PPAR) perspective to ascertain the improvement over other design techniques. A radiation hardened all-digital multiplying pulsed digital delay line (DDL) is designed for double data rate (DDR2/3) applications for data eye centering during high speed off-chip data transfer. The effect of noise, radiation particle strikes and statistical variation on the designed DDL are studied in detail. The design achieves the best in class 22.4 ps peak-to-peak jitter, 100-850 MHz range at 14 pJ/cycle energy consumption. Vulnerability of the non-hardened design is characterized and portions of the redundant DDL are separated in custom and auto-place and route (APR). Thus, a range of designs for mission critical applications are implemented using methodologies proposed in this work and their potential PPAR benefits explored in detail.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

A Construction Kit for Efficient Low Power Neural Network Accelerator Designs

Implementing embedded neural network processing at the edge requires efficient hardware acceleration that couples high computational performance with low power consumption. Driven by the rapid evolution of network architectures and their algorithmic features, accelerator designs are constantly updated and improved. To evaluate and compare hardware design choices, designers can refer to a myriad of accelerator implementations in the literature. Surveys provide an overview of these works but are often limited to system-level and benchmark-specific performance metrics, making it difficult to quantitatively compare the individual effect of each utilized optimization technique. This complicates the evaluation of optimizations for new accelerator designs, slowing-down the research progress. This work provides a survey of neural network accelerator optimization approaches that have been used in recent works and reports their individual effects on edge processing performance. It presents the list of optimizations and their quantitative effects as a construction kit, allowing to assess the design choices for each building block separately. Reported optimizations range from up to 10'000x memory savings to 33x energy reductions, providing chip designers an overview of design choices for implementing efficient low power neural network accelerators