Dark signalling and code division multiple access in an optical fibre LAN with a bus topology

This thesis describes an optical fibre network that uses a bus topology and Code Division Multiple Access (CDMA). Various potential configurations are analysed and compared and it is shown that a serious limitation of optical CDMA schemes using incoherent correlators is the effect of optical beating due to the presence of multiple incoherent optical signals at the receiver photodiode. The network proposed and analysed in this thesis avoids beating between multiple optical fields because it only uses a single, shared, optical source. It does this through the SLIM (Single Light-source with In-line Modulation) configuration in which there is a continuously-operating light source at the head-end of a folded bus, and modulators at the nodes to impose signals on the optical field in the form of pulses of darkness which propagate along the otherwise continuously bright bus. Optical CDMA can use optical-fibre delay-line correlators as matched filters, and these may be operated either coherently or incoherently.Coherent operation is significantly more complex than incoherent operation, but incoherent correlators introduce further beating even in a SLIM network. A new design of optical delay-line correlator, the hybrid correlator, is therefore proposed, analysed and demonstrated. It is shown to eliminate beating. A model of a complete network predicts that a SLIMbus using optical CDMA with hybrid correlators can be operated at TeraBaud rates with the number of simultaneous users limited by multiple access interference (MAI), determined only by the combinatorics of the code set

Co-channel interference reduction in Optical Code Division Multiple Access systems

In this thesis few new code sets and a multi-user interference (MUI) cancellation scheme have been proposed for Optical Code Division Multiple Access (OCDMA) systems, which can be employed in the next generation of global communication networks to enhance their existing systems’ performance dramatically. The initial evaluation of the proposed code sets shows that their implementation improves the performance, decreases the BER and increases security considerably. Also the proposed MUI cancellation scheme totally removes all the cross-talk and interference between the active users within the network. These novel schemes and codes can be easily implemented in the optical packet switched networks. Optical switching has the ability of bandwidth manipulation at the wavelength level (e.g. with optical circuit/packet/burst switching); the capability to accommodate a wide range of traffic distributions, and also to make dynamic resource reservations possible. This thesis first gives a brief overview of co-channel interference reduction in OCDMA networks, then proposes two novel code sets, Uniform Cross-Correlation Modified Prime Code (UC-MPC) and Transposed UC-MPC (T-UCMPC), along with their evaluation and analysis in various systems, including IP routing over an OCDMA network. Thereafter, the new MUI cancellation scheme is proposed and then the proposed code sets and the MUI cancellation scheme are implemented and analysed in a laboratory-based experimental test bed. Finally the conclusion of this research is discussed

Applications of perfect difference codes in fiber-optics and wireless optical code-division multiplexing/multiple-access systems

After establishing itself in the radio domain, Spread spectrum code-division multiplexing/multiple-access (CDMA) has seen a recent upsurge in optical domain as well. Due to its fairness, flexibility, service differentiation and increased inherent security, CDMA is proved to be more suitable for the bursty nature of local area networks than synchronous multiplexing techniques like Frequency/Wavelength Division Multiplexing (F/WDM) and Time Division Multiplexing (TDM). In optical domain, CDMA techniques are commonly known as Optical-CDMA (O-CDMA). All optical CDMA systems are plagued with the problem of multiple-access interference (MAI). Spectral amplitude coding (SAC) is one of the techniques used in the literature to deal with the problem of MAI. The choice of spreading code in any CDMA system is another way to ensure the successful recovery of data at the receiving end by minimizing the effect of MAI and it also dictates the hardware design of the encoder and decoder. This thesis focuses on the efficient design of encoding and decoding hardware. Perfect difference codes (PDC) are chosen as spreading sequences due to their good correlation properties. In most of the literature, evaluation of error probability is based on the assumptions of ideal conditions. Such assumptions ignore major physical impairments such as power splitting losses at the multiplexers of transmitters and receivers, and gain losses at the receivers, which may in practice be an overestimate or underestimate of the actual probability of error. This thesis aims to investigate thoroughly with the consideration of practical impairments the applications of PDCs and other spreading sequences in optical communications systems based on spectral-amplitude coding and utilizing codedivision as multiplexing/multiple-access technique. This work begins with a xix general review of optical CDMA systems. An open-ended practical approach has been used to evaluate the actual error probabilities of OCDM/A systems under study. It has been concluded from results that mismatches in the gains of photodetectors, namely avalanche photodiode (APDs), used at the receiver side and uniformity loss in the optical splitters results in the inaccurate calculation of threshold level used to detect the data and can seriously degrade the system bit error rate (BER) performance. This variation in the threshold level can be compensated by employing techniques which maintain a constant interference level so that the decoding architecture does not have to estimate MAI every time to make a data bit decision or by the use of balanced sequences. In this thesis, as a solution to the above problem, a novel encoding and decoding architecture is presented for perfect difference codes based on common zero code technique which maintains a constant interference level at all instants in CDM system and thus relieves the need of estimating interference. The proposed architecture only uses single multiplexer at the transmitters for all users in the system and a simple correlation based receiver for each user. The proposed configuration not only preserves the ability of MAI in Spectral-Amplitude Coding SAC-OCDM system, but also results in a low cost system with reduced complexity. The results show that by using PDCs in such system, the influence of MAI caused by other users can be reduced, and the number of active users can be increased significantly. Also a family of novel spreading sequences are constructed called Manchestercoded Modified Legendre codes (MCMLCs) suitable for SAC based OCDM systems. MCMLCs are designed to be used for both single-rate and Multirate systems. First the construction of MCMLCs is presented and then the bit error rate performance is analyzed. Finally the proposed encoding/decoding architecture utilizing perfect difference codes is applied in wireless infrared environment and the performance is found to be superior to other codes

Simulation and Noise Analysis of Multimedia Transmission in Optical CDMA Computer Networks

This paper simulates and analyzes noise of multimedia transmission in a flexible optical code division multiple access (OCDMA) computer network with different quality of service (QoS) requirements. To achieve multimedia transmission in OCDMA, we have proposed strict variable-weight optical orthogonal codes (VW-OOCs), which can guarantee the smallest correlation value of one by the optimal design. In developing multimedia transmission for computer network, a simulation tool is essential in analyzing the effectiveness of various transmissions of services. In this paper, implementation models are proposed to analyze the multimedia transmission in the representative of OCDMA computer networks by using MATLAB simulink tools. Simulation results of the models are discussed including spectrums outputs of transmitted signals, superimposed signals, received signals, and eye diagrams with and without noise. Using the proposed models, multimedia OCDMA computer network using the strict VW-OOC is practically evaluated. Furthermore, system performance is also evaluated by considering avalanche photodiode (APD) noise and thermal noise. The results show that the system performance depends on code weight, received laser power, APD noise, and thermal noise which should be considered as important parameters to design and implement multimedia transmission in OCDMA computer networks

Throughput Performance Evaluation of Multiservice Multirate OCDMA in Flexible Networks

\u3cp\u3eIn this paper, new analytical formalisms to evaluate the packet throughput of multiservice multirate slotted ALOHA optical code-division multiple-access (OCDMA) networks are proposed. The proposed formalisms can be successfully applied to 1-D and 2-D OCDMA networks with any number of user classes in the system. The bit error rate (BER) and packet correct probability expressions are derived, considering the multiple-access interference as binomially distributed. Packet throughput expressions, on the other hand, are derived considering Poisson, binomial, and Markov chain approaches for the composite packet arrivals distributions, with the latter defined as benchmark. A throughput performance evaluation is carried out for two distinct user code sequences separately, namely, 1-D and 2-D multiweight multilength optical orthogonal code (MWML-OOC). Numerical results show that the Poisson approach underestimates the throughput performance in unacceptable levels and incorrectly predicts the number of successfully received packets for most offered load values even in favorable conditions, such as for the 2-D MWML-OOC OCDMA network with a considerably large number of simultaneous users. On the other hand, the binomial approach proved to be more straightforward, computationally more efficient, and just as accurate as the Markov chain approach.\u3c/p\u3

Coherent optical code division multiple access based on superstructure fiber bragg grating encoders and decoders.

Li Xin.Thesis (M.Phil.)--Chinese University of Hong Kong, 2003.Includes bibliographical references (leaves 81-86).Abstracts in English and Chinese.COHERENT OPTICAL CODE DIVISION MULTIPLE ACCESS BASED ON SUPERSTRUCTURE FIBER BRAGG GRATING ENCODERS AND DECODERS --- p.1ACKNOWLEDGEMENT --- p.2ABSTRACT --- p.III摘要 --- p.VCONTENTS --- p.VILIST OF FIGURES --- p.1Chapter CHAPTER 1 --- INTRODUCTION --- p.3Chapter 1.1 --- Overview of OCDMA --- p.3Chapter 1.2 --- Classification of OCDMA Schemes --- p.6Chapter 1.3 --- Introduction of Coherent OCDMA Schemes --- p.9Chapter 1.4 --- Introduction of superstructure Fiber Bragg Gratings and Other Encoding and Decoding Components --- p.10Chapter 1.5 --- Outline of the Thesis --- p.13Chapter CHAPTER 2 --- COUPLED MODE THEORY AND SUPERSTRUCTURE FIBER BRAGG GRATING SIMULATION MODEL --- p.16Chapter 2.1 --- Fiber Bragg Grating Model Based on Coupled Mode Theory --- p.16Chapter 2.1.1 --- Introduction of FBG and the Coupled Mode Theory --- p.16Chapter 2.1.2 --- FBG Model Based on CMT --- p.18Chapter 2.1.3 --- FBG Model When there are Phase Discontinuities Between Different Parts --- p.20Chapter 2.2 --- Properties of Fiber Bragg Gratings --- p.22Chapter 2.3 --- Simulation Model of superstructure Fiber Bragg Gratings --- p.27Chapter 2.4 --- Summary --- p.31Chapter CHAPTER 3 --- COHERENT OCDMA CODING SCHEME BASED ON THE SUPERSTRUCTURE FIBER BRAGG GRATING ENCODER/DECODER --- p.33Chapter 3.1 --- Introduction and Theoretical Derivation of the Coding Scheme --- p.33Chapter 3.1.1 --- Introduction of the Coding Scheme --- p.33Chapter 3.1.2 --- Derivation of SSFBG Encoder --- p.34Chapter 3.1.3 --- Encoding for the SSFBG --- p.39Chapter 3.2 --- Introduction of the Simulation Model and the Research on It …… --- p.44Chapter 3.3 --- Summary --- p.47Chapter CHAPTER 4 --- RESEARCH ON THE SIMULATED COHERENT OCDMA SYSTEM IN IDEAL CASE --- p.48Chapter 4.1 --- Introduction of the ideal case and factors that affect the system performance --- p.48Chapter 4.2 --- Effects by Refractive Index Modulation of the SSFBG Encoder --- p.49Chapter 4.3 --- Effects by Code Type --- p.54Chapter 4.4 --- Effect by the Code Length --- p.57Chapter 4.5 --- Summary --- p.60Chapter CHAPTER 5 --- RESEARCH ON THE SIMULATED COHERENT OCDMA SYSTEM IN PRACTICAL ENVIRONMENT --- p.62Chapter 5.1 --- Introduction --- p.62Chapter 5.2 --- Comparison of System Performance in Synchronous and Asynchronous Cases --- p.63Chapter 5.3 --- Discussion on the System Performance When Users are In Different Power Levels --- p.65Chapter 5.4 --- Analysis of Channel Noise In the Coherent OCDMA System --- p.68Chapter 5.5 --- Summary --- p.70Chapter CHAPTER 6 --- CONCLUSIONS AND FUTURE WORK --- p.72Chapter 6.1 --- Conclusions --- p.72Chapter 6.2 --- Future Work --- p.75APPENDIX A PROOF OF SSFBG THEORETICAL MODEL APPROXIMATION --- p.77"APPENDIX B RANDOM SEQUENCE, M-SEQUENCE AND WALSH SEQUENCE" --- p.80REFERENCES --- p.8

Monitoring of passive optical networks utilising an optical coding technique

Passive Optical Networks (PONs) have become the most popular fibre based access networks over the last decade. They are widely deployed for use in Fibre-to-the-Premises (FTTP) scenarios. PON is a point-to-multipoint connection (P2MP) between an optical line terminal (OLT) located at the central office (CO) and multiple optical network units (ONU) at the customer premises. The next generation of PONs (NG-PON) are likely to deploy a ring-and-spur long reach PON (LR-PON). NG-PON aims to accommodate more ONUs, extend the network coverage out to 100 km, minimize complexity and improve operational outcomes. An all fibre access network, operating over extended distances, presents a reliability risk, thereby increasing the need for a reliable and cost-effective monitoring system to enhance protection and reduce restoration time. Among existing monitoring techniques, attention is focused on approaches that use optical code division multiplexing (OCDM), also known as optical coding (OC). The OC is applied to a signal that is sent from the network management system (NMS) to the ONUs. The monitoring signal is transmitted onto a fibre and split into a number of sub-signals that are equal in number to the ONUs. Each one of the ONUs receives a sub-signal, encodes it, and then reflects it back to the NMS. The NMS has the capability to identify faulty ONUs by examining the code received from the ONUs. A review of the literature has shown that the use of OCs does improve system performance, especially in the timely detection of faults. Many of the studies, found in the literature, focus on how to implement optical spreading codes that are used in OCDM Access (OCDMA) systems and currently the optical orthogonal code (OOC) is the dominant code implemented for time-domain coding. Although the OOC code performs well, its construction is relatively complex. The available code-words (cardinality) that are offered by OOC are proportional to the code length. Implementing OOC in a high capacity PON requires a long code length causes an inevitable degradation of system performance. Therefore, an improved optical coding technique for PONs should provide code-words that conform to PON split ratios. The main objective of the research was to develop an optical spreading code, based on a prime code family for OCDMA systems, that has the capability to accommodate different PON split ratios and with characteristics that improve transmission system performance when compared to existing prime code families. The novel code presented in this thesis is identified as the extended grouped new modified prime code (EG-nMPC). The number of code-words generated by the proposed codes are substantially higher than those generated by the existing code families and more compatible to the different PON splitting ratios. In addition, with a low code weight, both power consumption and hardware complexity decreases. The code performance was evaluated using mathematical models for two transmission formats - pulse position modulation (PPM) and on-off keying (OOK) modulation. The performance of EG-nMPC was compared to other prime codes, and the results show that the proposed code improves the performance of OCDMA in terms of bit-error rate (BER). As PON is a point-to-multipoint connection oriented access network, downstream traffic is encrypted and broadcast to all ONUs, while the unencrypted upstream traffic from each ONU terminal occurs in a burst mode. The OLT carries out a ranging process to determine transmission delays between ONUs, to prevent collisions between the burst mode traffic from each of the ONUs. In this research, the burst mode traffic ranging process has been replicated in the monitoring system, with this replication providing a fixed equalization delay time for the monitoring transmissions. To investigate the ring-and-spur LR-PON reliability several protection architectures were evaluated, in term of cost and availability, to determine the optimal protection architecture. In this thesis, the reliability parameter Failure Impact Robustness (FIR), has been used to calculate the failure impact of the different components in ring-and-spur LR-PON, hence selecting the optimal protection scheme. A PON-based optical communication system model was developed and the proposed EG-nMPC code was incorporated. Fibre split ratios of 32, 64 and 128, were considered in this study. The simulation results show that the EG-nMPC code improves the performance, efficiency and accuracy of the PON transmission monitoring system. To conclude, this research aims to enhance the PON performance by a fast detection of the fault and quick restoration. This research has contributed to knowledge by identifying a new and novel spreading code that is compatible with the different PON splitting ratios for OC monitoring techniques. By using the ranging process, a fixed equalization delay time has been assigned to each ONU to manage the upstream burst traffic. The spreading code has been implemented in a real-time simulation to show the status of each fibre link. The implementation was carried out based on 1-D tree topology system. However, the proposed EG-nMPC can be exploited to enable network monitoring that is based on hybrid 1D/2D coding. This coding is complementary with the structure of LR-PON as explained in section ‎8.2.3. In addition, with the use of the FIR parameter for the different components in the ring-and-spur architecture, an optimal protection scheme for both OLT and the ring (feeder fibre), has been nominated. This protection scheme ensures that protection, availability and cost are at their optimal values