Spatial Multiplexing of QPSK Signals with a Single Radio: Antenna Design and Over-the-Air Experiments

The paper describes the implementation and performance analysis of the first fully-operational beam-space MIMO antenna for the spatial multiplexing of two QPSK streams. The antenna is composed of a planar three-port radiator with two varactor diodes terminating the passive ports. Pattern reconfiguration is used to encode the MIMO information onto orthogonal virtual basis patterns in the far-field. A measurement campaign was conducted to compare the performance of the beam-space MIMO system with a conventional 2-by-?2 MIMO system under realistic propagation conditions. Propagation measurements were conducted for both systems and the mutual information and symbol error rates were estimated from Monte-Carlo simulations over the measured channel matrices. The results show the beam-space MIMO system and the conventional MIMO system exhibit similar finite-constellation capacity and error performance in NLOS scenarios when there is sufficient scattering in the channel. In comparison, in LOS channels, the capacity performance is observed to depend on the relative polarization of the receiving antennas.Comment: 31 pages, 23 figure

Modal characterization of the ASCIE segmented optics testbed: New algorithms and experimental results

New frequency response measurement procedures, on-line modal tuning techniques, and off-line modal identification algorithms are developed and applied to the modal identification of the Advanced Structures/Controls Integrated Experiment (ASCIE), a generic segmented optics telescope test-bed representative of future complex space structures. The frequency response measurement procedure uses all the actuators simultaneously to excite the structure and all the sensors to measure the structural response so that all the transfer functions are measured simultaneously. Structural responses to sinusoidal excitations are measured and analyzed to calculate spectral responses. The spectral responses in turn are analyzed as the spectral data become available and, which is new, the results are used to maintain high quality measurements. Data acquisition, processing, and checking procedures are fully automated. As the acquisition of the frequency response progresses, an on-line algorithm keeps track of the actuator force distribution that maximizes the structural response to automatically tune to a structural mode when approaching a resonant frequency. This tuning is insensitive to delays, ill-conditioning, and nonproportional damping. Experimental results show that is useful for modal surveys even in high modal density regions. For thorough modeling, a constructive procedure is proposed to identify the dynamics of a complex system from its frequency response with the minimization of a least-squares cost function as a desirable objective. This procedure relies on off-line modal separation algorithms to extract modal information and on least-squares parameter subset optimization to combine the modal results and globally fit the modal parameters to the measured data. The modal separation algorithms resolved modal density of 5 modes/Hz in the ASCIE experiment. They promise to be useful in many challenging applications

Identification of Bare-Airframe Dynamics from Closed-Loop Data Using Multisine Inputs and Frequency Responses

Amethod is presented for computing multiple-input multiple-output frequency responses of bare-airframe dynamics for systems excited using orthogonal phase-optimized multisines and including correlated data arising from control mixing or feedback control. The estimation was posed as the solution to an underdetermined system of linear equations, for which additional information was supplied using interpolation of the frequency responses. A simulation model of the NASA T-2 aircraft having two inputs and two outputs was used to investigate the method in the open-loop configuration and under closed-loop control. The method was also applied to flight test data from the X-56A aeroelastic demonstrator having five inputs and ten outputs and flying under closed-loop control with additional control allocation mixing. Results demonstrated that the proposed method accurately estimates the bare airframe frequency responses in the presence of correlated data from control mixing and feedback control. Results also agreed with estimates obtained using different methods that are less sensitive to correlated inputs

Optical Space Division Multiplexing in Short Reach Multi-Mode Fiber Systems

The application of space division multiplexing to fiber-optic communications is a promising approach to further increase the channel capacity of optical waveguides. In this work, short reach and low-cost optical space division multiplexing systems with intensity modulation and direct detection (IM/DD) are in the focus of interest. Herein, different modes are utilized to generate spatial diversity in a multi-mode fiber. In such IM/DD systems, the process of square-law detection is inherently non-linear. In order to obtain an understanding of the channel characteristics, a system model is developed, which is able to show under which conditions the system can be considered linear in baseband. It is shown that linearity applies in scenarios with low mode cross-talk. This enables the use of linear multiple-input multiple-output (MIMO) signal processing strategies for equalization purposes. In conditions with high mode cross-talk, significant interference occurs, and the transmitted information cannot be extracted at the receiver. Furthermore, a method to determine the power coupling coefficients between mode groups is presented that does not require the excitation of individual modes, and hence it can be realized with inexpensive components. In addition, different optical components are analyzed with respect for their suitability in MIMO setups with IM/DD. The conventional approach with single-mode fiber to multi-mode fiber offset launches and optical couplers as well as a configuration that utilizes multi-segment detection are feasible options for a (2x2) setup. It is further shown that conventional photonic lanterns are not suited for MIMO with IM/DD due to their low mode orthogonality during the multiplexing process. In order to enable higher order MIMO configurations, devices for mode multiplexing and demultiplexing need to be developed, which exhibit a high mode orthogonality on one hand and are low-cost on the other hand

Circuit Based Optimization of Radiation Characteristics of Single and Multi-Port Antennas

A method for analyzing and optimizing multiport antennas is presented and exemplified. The method was first presented in [1]-[3] and uses data from full wave electromagnetic field (EM) solvers in combination with circuit simulations for efficient calculations of radiation properties of multi-port antennas. The main advantage of the proposed method is that only a few full-wave simulations, which usually are time consuming, are needed when e.g. optimizing the matching circuits for a multi-port antenna. Since embedded element patterns are used, all relevant antenna parameters such as radiation efficiency, diversity gain, available MIMO capacity etc. can efficiently be computed for any port excitation and loading configuration. The methodology has been implemented in software called MPA (Multi-Port Antenna evaluator) which imports port response matrices and embedded element patterns from commercial full-wave codes and post processes the data making it possible to e.g. optimize capacity for a MIMO system. The optimization is done by changing the feeding and matching networks in a circuit simulator that is invoked by the MPA. Finally the software is used on two examples which are analyzed and optimized to illustrate the potential of the method