Developing a framework of non-fatal occupational injury surveillance for risk control in palm oil mills

Non-fatal occupational injury (NFOI) and its risk factors have become a current global concern. The need of research towards the relationship between occupational injury and its risk factor is essential, to fulfil the purpose and setting the priority of implementing safety preventive approaches at workplace. This research intended to develop a framework of NFOI surveillance by using epidemiological data, noise exposure data and NFOI data among palm oil mills’ workers. A total of 420 respondents who assigned in operation and processing areas (OP) (n=333) and general or office workers (n=87) had voluntary participated in this research. A questionnaire session with respondents was held to obtain epidemiological data and NFOI information via validated questionnaire. Noise hazard monitoring was executed by using Sound Level Meter (SLM) for environmental noise monitoring and Personal Sound Dosimeter for personal noise monitoring. Gathered data were analysed in quantitative method by using statistical software IBM SPSS Statistic version 21 and a risk matrix table for injury risk rating evaluation. It was discovered that high noise exposure level (≥ 85 dB[A]) was significantly associated with non-fatal occupational injury among OP workers (φ=0.123, p<0.05) with OR=1.87 (95% CI, 1.080-3.235, p<0.05). Risk rating for reported NFOI was at moderate level, with minor cuts and scratches were the dominant type of injury (42.6%). Analysis of logistic regression indicated that working in shift, not wearing protective gloves, health problems such as shortness of breath and ringing in ears, and excessive noise level (≥ 85 dB[A]) were the risk factors of NFOI in palm oil mills among OP workers. A framework of nonfatal injury surveillance in palm oil mills was developed based on the findings with integration of risk management process and injury prevention principles. This framework is anticipated to help the management in decision making for preventive actions and early detection of occupational health effects among workers

High Gain Amplifier with Enhanced Cascoded Compensation

A two-stage CMOS operational amplifier with both, gain-boosting and indirect current feedback frequency compensation performed by means of regulated cascode amplifiers, is presented. By using quasi-floating-gate transistors (QFGT) the supply requirements, the number of capacitors and the size of the compensation capacitors respect to other Miller schemes are reduced. A prototype was fabricated using a 0.5 μm technology, resulting, for a load of 45 pF and supply voltage of 1.65 V, in open-loop-gain of 129 dB, 23 MHz of gain-bandwidth product, 60o phase margin, 675 μW power consumption and 1% settling time of 28 ns

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Low-Power Slew-Rate Boosting Based 12-Bit Pipeline ADC Utilizing Forecasting Technique in the Sub-ADCS

The dissertation presents architecture and circuit solutions to improve the power efficiency of high-speed 12-bit pipelined ADCs in advanced CMOS technologies. First, the 4.5bit algorithmic pipelined front-end stage is proposed. It is shown that the algorithmic pipelined ADC requires a simpler sub-ADC and shows lower sensitivity to the Multiplying DAC (MDAC) errors and smaller area and power dissipation in comparison to the conventional multi-bit per stage pipelined ADC. Also, it is shown that the algorithmic pipelined architecture is more tolerant to capacitive mismatch for the same input-referred thermal noise than the conventional multi-bit per stage architecture. To take full advantage of these properties, a modified residue curve for the pipelined ADC is proposed. This concept introduces better linearity compared with the conventional residue curve of the pipelined ADC; this approach is particularly attractive for the digitization of signals with large peak to average ratio such as OFDM coded signals. Moreover, the minimum total required transconductance for the different architectures of the 12-bit pipelined ADC are computed. This helps the pipelined ADC designers to find the most power-efficient architecture between different topologies based on the same input-referred thermal noise. By employing this calculation, the most power efficient architecture for realizing the 12-bit pipelined ADC is selected. Then, a technique for slew-rate (SR) boosting in switched-capacitor circuits is proposed in the order to be utilized in the proposed 12-bit pipelined ADC. This technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high slew-rate is demanded by large input signal. The proposed architecture employs simple circuitry to detect the need of injecting current at the output load by implementing a Pre-Amp followed by a class-B amplifier, embedded with a pre-defined hysteresis, in parallel with the main amplifier to boost its slew phase. The proposed solution requires small static power since it does not need high dc-current at the output stage of the main amplifier. The proposed technique is suitable for high-speed low-power multi-bit/stage pipelined ADC applications. Both transistor-level simulations and experimental results in TSMC 40nm technology reduces the slew-time for more than 45% and shorts the 1% settling time by 28% when used in a 4.5bit/stage pipelined ADC; power consumption increases by 20%. In addition, the technique of inactivating and disconnecting of the sub-ADC’s comparators by forecasting the sign of the sampled input voltage is proposed in the order to reduce the dynamic power consumption of the sub-ADCs in the proposed 12-bit pipelined ADC. This technique reduces the total dynamic power consumption more than 46%. The implemented 12-bit pipelined ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and a 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm^2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively

Performance enhancement in the desing of amplifier and amplifier-less circuits in modern CMOS technologies.

In the context of nowadays CMOS technology downscaling and the increasing demand of high performance electronics by industry and consumers, analog design has become a major challenge. On the one hand, beyond others, amplifiers have traditionally been a key cell for many analog systems whose overall performance strongly depends on those of the amplifier. Consequently, still today, achieving high performance amplifiers is essential. On the other hand, due to the increasing difficulty in achieving high performance amplifiers in downscaled modern technologies, a different research line that replaces the amplifier by other more easily achievable cells appears: the so called amplifier-less techniques. This thesis explores and contributes to both philosophies. Specifically, a lowvoltage differential input pair is proposed, with which three multistage amplifiers in the state of art are designed, analysed and tested. Moreover, a structure for the implementation of differential switched capacitor circuits, specially suitable for comparator-based circuits, that features lower distortion and less noise than the classical differential structures is proposed, an, as a proof of concept, implemented in a ΔΣ modulator

A 90 dB, 85 MHz operational transconductance amplifier (OTA) using gain boosting technique

Gain and speed are the two most important parameters of an amplifier. Optimizing an amplifier for both of these parameters leads to contradicting demands. Various architectures have been reported to obtain high gain from the circuits. Cascode circuits are widely used in circuit design at places where high gain and high output impedances are required. Different architectures like triple cascode topology, dynamic biasing and a positive feedback amplifier have been used to obtain high gains. These architectures have been compared in this thesis along with drawbacks and advantages of each

A 93.36 dB, 161 MHz CMOS Operational Transconductance Amplifier (OTA) for a 16 Bit Pipeline Analog-to-Digital Converter (ADC)

A gain modified CMOS Operational Transconductance Amplifier (OTA) for a 16 bit pipeline Analog-to-Digital Converter (ADC) is presented. The circuit is designed to be used for a high resolution and low sampling rate ADC. Gain boosting technique is implemented in the design to achieve high DC gain and settling time as required. Post layout simulations for a 5 pF load capacitance shows that OTA achieves a gain bandwidth of 161 MHz at a phase margin 93.14o with 93.27 dB DC gain. The settling time for an OTA is 163 ns for 0.1 % accuracy to achieve final value and consume power about 4.88 mW from 5 V power supply.Keywords: ADC; common mode feedback; CMOS Operational Amplifier; fully differential folded cascadeDOI:http://dx.doi.org/10.11591/ijece.v2i1.12