Design of a single-chip pH sensor using a conventional 0.6-μm CMOS process

A pH sensor fabricated on a single chip by an unmodified, commercial 0.6-/spl μm CMOS process is presented. The sensor comprises a circuit for making differential measurements between an ion-sensitive field-effect transistor (ISFET) and a reference FET (REFET). The ISFET has a floating-gate structure and uses the silicon nitride passivation layer as a pH-sensitive insulator. As fabricated, it has a large threshold voltage that is postulated to be caused by a trapped charge on the floating gate. Ultraviolet radiation and bulk-substrate biasing is used to permanently modify the threshold voltage so that the ISFET can be used in a battery-operated circuit. A novel post-processing method using a single layer of photoresist is used to define the sensing areas and to provide robust encapsulation for the chip. The complete circuit, operating from a single 3-V supply, provides an output voltage proportional to pH and can be powered down when not required

Low Voltage Floating Gate MOS Transistor Based Four-Quadrant Multiplier

This paper presents a four-quadrant multiplier based on square-law characteristic of floating gate MOSFET (FGMOS) in saturation region. The proposed circuit uses square-difference identity and the differential voltage squarer proposed by Gupta et al. to implement the multiplication function. The proposed multiplier employs eight FGMOS transistors and two resistors only. The FGMOS implementation of the multiplier allows low voltage operation, reduced power consumption and minimum transistor count. The second order effects caused due to mobility degradation, component mismatch and temperature variations are discussed. Performance of the proposed circuit is verified at ±0.75 V in TSMC 0.18 µm CMOS, BSIM3 and Level 49 technology by using Cadence Spectre simulator

High-Linearity Self-Biased CMOS Current Buffer

A highly linear fully self-biased class AB current buffer designed in a standard 0.18 mu m CMOS process with 1.8 V power supply is presented in this paper. It is a simple structure that, with a static power consumption of 48 mu W, features an input resistance as low as 89 Omega, high accuracy in the input-output current ratio and total harmonic distortion (THD) figures lower than -60 dB at 30 mu A amplitude signal and 1 kHz frequency. Robustness was proved through Monte Carlo and corner simulations, and finally validated through experimental measurements, showing that the proposed configuration is a suitable choice for high performance low voltage low power applications

Power-efficient current-mode analog circuits for highly integrated ultra low power wireless transceivers

In this thesis, current-mode low-voltage and low-power techniques have been applied to implement novel analog circuits for zero-IF receiver backend design, focusing on amplification, filtering and detection stages. The structure of the thesis follows a bottom-up scheme: basic techniques at device level for low voltage low power operation are proposed in the first place, followed by novel circuit topologies at cell level, and finally the achievement of new designs at system level. At device level the main contribution of this work is the employment of Floating-Gate (FG) and Quasi-Floating-Gate (QFG) transistors in order to reduce the power consumption. New current-mode basic topologies are proposed at cell level: current mirrors and current conveyors. Different topologies for low-power or high performance operation are shown, being these circuits the base for the system level designs. At system level, novel current-mode amplification, filtering and detection stages using the former mentioned basic cells are proposed. The presented current-mode filter makes use of companding techniques to achieve high dynamic range and very low power consumption with for a very wide tuning range. The amplification stage avoids gain bandwidth product achieving a constant bandwidth for different gain configurations using a non-linear active feedback network, which also makes possible to tune the bandwidth. Finally, the proposed current zero-crossing detector represents a very power efficient mixed signal detector for phase modulations. All these designs contribute to the design of very low power compact Zero-IF wireless receivers. The proposed circuits have been fabricated using a 0.5μm double-poly n-well CMOS technology, and the corresponding measurement results are provided and analyzed to validate their operation. On top of that, theoretical analysis has been done to fully explore the potential of the resulting circuits and systems in the scenario of low-power low-voltage applications.Programa Oficial de Doctorado en Tecnologías de las Comunicaciones (RD 1393/2007)Komunikazioen Teknologietako Doktoretza Programa Ofiziala (ED 1393/2007

Impact of atomistic device variability on analogue circuit design

Scaling of complementary metal-oxide-semiconductor (CMOS) technology has benefited the semiconductor industry for almost half a century. For CMOS devices with a physical gate-length in the sub-100 nm range, extreme device variability is introduced and has become a major stumbling block for next generation analogue circuit design. Both opportunities and challenges have therefore confronted analogue circuit designers. Small geometry device can enable high-speed analogue circuit designs, such as data conversion interfaces that can work in the radio frequency range. These designs can be co-integrated with digital systems to achieve low cost, high-performance, single-chip solutions that could only be achieved using multi-chip solutions in the past. However, analogue circuit designs are extremely vulnerable to device mismatch, since a large number of symmetric transistor pairs and circuit cells are required. The increase in device variability from sub-100 nm processes has therefore significantly reduced the production yield of the conventional designs. Mismatch models have been developed to analytically evaluate the magnitude of random variations. Based on measurements from custom designed test structures, the statistics of process variation can be estimated using design related parameters. However, existing models can no longer accurately estimate the magnitude of mismatch for sub-100 nm “atomistic” devices, since short-channel effects have become important. In this thesis, a new mismatch model for small geometry devices will be proposed to address this problem. Based on knowledge of the matching performance obtained from the mismatch model, design solutions are desired at different design levels for a variety of circuit topologies. In this thesis, transistor level compensation solutions have been investigated and closed-loop compensation circuits have been proposed. At circuit level, a latch-based comparator has been used to develop a compensation solution because this type of comparator is extremely sensitive to the device mismatch. These comparators are also used as the fundamental building block for the analogue-to-digital converters (ADC). The proposed comparator compensation scheme is used to improve the performance of a high-speed flash ADC

Adaptation of Current Signals with Floating-Gate Circuits

In this paper we present a new, adaptive spatial-derivative circuit for CMOS image sensors. The circuit removes its offset as a natural part of its operation using a combination of electron tunneling and hot-electron injection to add or remove charge on a floating-gate of an auto-zeroing amplifier. We designed, fabricated and successfully tested a chip with the circuit. Test results show that the circuit reduces the offsets by more than an order of magnitude

Low Power Adaptive Circuits: An Adaptive Log Domain Filter and A Low Power Temperature Insensitive Oscillator Applied in Smart Dust Radio

This dissertation focuses on exploring two low power adaptive circuits. One is an adaptive filter at audio frequency for system identification. The other is a temperature insensitive oscillator for low power radio frequency communication. The adaptive filter is presented with integrated learning rules for model reference estimation. The system is a first order low pass filter with two parameters: gain and cut-off frequency. It is implemented using multiple input floating gate transistors to realize online learning of system parameters. Adaptive dynamical system theory is used to derive robust control laws in a system identification task. Simulation results show that convergence is slower using simplified control laws but still occurs within milliseconds. Experimental results confirm that the estimated gain and cut-off frequency track the corresponding parameters of the reference filter. During operation, deterministic errors are introduced by mismatch within the analog circuit implementation. An analysis is presented which attributes the errors to current mirror mismatch. The harmonic distortion of the filter operating in different inversion is analyzed using EKV model numerically. The temperature insensitive oscillator is designed for a low power wireless network. The system is based on a current starved ring oscillator implemented using CMOS transistors instead of LC tank for less chip area and power consumption. The frequency variance with temperature is compensated by the temperature adaptive circuits. Experimental results show that the frequency stability from 5°C to 65°C has been improved 10 times with automatic compensation and at least 1 order less power is consumed than published competitors. This oscillator is applied in a 2.2GHz OOK transmitter and a 2.2GHz phase locked loop based FM receiver. With the increasing needs of compact antenna, possible high data rate and wide unused frequency range of short distance communication, a higher frequency phase locked loop used for BFSK receiver is explored using an LC oscillator for its capability at 20GHz. The success of frequency demodulation is demonstrated in the simulation results that the PLL can lock in 0.5μs with 35MHz lock-in range and 2MHz detection resolution. The model of a phase locked loop used for BFSK receiver is analyzed using Matlab

A Current-Mode Multi-Channel Integrating Analog-to-Digital Converter

Multi-channel analog to digital converters (ADCs) are required where signals from multiple sensors can be digitized. A lower power per channel for such systems is important in order that when the number of channels is increased the power does not increase drastically. Many applications require signals from current output sensors, such as photosensors and photodiodes to be digitized. Applications for these sensors include spectroscopy and imaging. The ability to digitize current signals without converting currents to voltages saves power, area, and the design time required to implement I-to-V converters. This work describes a novel and unique current-mode multi-channel integrating ADC which processes current signals from sensors and converts it to digital format. The ADC facilitates the processing of current analog signals without the use of transconductors. An attempt has been made also to incorporate voltage-mode techniques into the current-mode design so that the advantages of both techniques can be utilized to augment the performance of the system. Additionally since input signals are in the form of currents, the dynamic range of the ADC is less dependant on the supply voltage. A prototype 4-channel ADC design was fabricated in a 0.5-micron bulk CMOS process. The measurement results for a 10Ksps sampling rate include a DNL, which is less than 0.5 LSB, and a power consumption of less than 2mW per channel