Double functionality concurrent dual-band self-oscillating mixer

A concurrent dual-band self-oscillating mixer (SOM), based on a ring-shaped stepped-impedance resonator, is proposed and analyzed in detail. Taking advantage of the ring even and odd resonances, the circuit can operate in concurrent dual quasi-periodic mode and injection-locked mode. In the second case, it behaves as a dual-band zero-intermediate-frequency (IF) mixer. Initially, an analytical study of the SOM behavior in the two modes is presented. Then a variety of accurate numerical methods are used for an in-depth investigation of the main aspects of its performance, including stability, conversion gain, linearity, and phase noise. The recently proposed contour-intersection technique and the outer-tier perturbation analysis are suitably adapted to the SOM case. A method is also presented to distinguish the parameter intervals leading to heterodyne and to zero-IF operation at both the lower and upper frequency bands. In the zero-IF SOM, the possible instantaneous unlocking in the presence of modulated input signals is investigated and avoided. The methods have been applied to a dual mixer at the frequencies 2.4 and 4.1 GHz.This work was supported by the Spanish Ministry of Economy and Competitiveness through the European Regional Development Fund (ERDF)/ Fondo Europeo de Desarrollo Regional (FEDER) and under Project TEC2017-88242-C3-(1/2)-R

Ultra-High Q-Factor Silicon Resonator for High Frequency Oscillators

The thesis focuses on the investigation and characterisation of ultra-high Q-factor low loss Silicon resonators with transverse electric (TE)-like electromagnetic band-gap determined by two dimensional periodic structure made of a Silicon slab having a triangular lattice of air cylinders. A band-gap is observed where no energy is propagated through the slab, however engineering defects are created and optimised within the lattice producing resonant cavities and waveguides. The structure being excited with the fundamental TE10 mode can be coupled to external circuits via waveguides and its respective transitions in co-planar waveguide transmission line used to convey the millimetre-wave frequency signals. The ultimate goal is to investigate and characterise the promising low loss and high frequency Silicon resonators suitable for millimetre-wave communications such as used in low phase noise oscillator application and band pass filters. The results clearly show that electromagnetic band-gap structures or photonic crystals (PC) can be utilized for application in high frequency oscillators directly in fundamental mode with great benefits in obtaining ultra-high Q-factor and therefore low phase noise; and with better performance than alternative state-of-art technologies such as crystal oscillators in combination with frequency multiplication or frequency synthesis causing an increase in the overall phase noise by 20 log rule. By successfully demonstrating the experiment of using electromagnetic band-gap structures with oscillators, it is a great contribution towards the solution of the problem of high phase noise affecting high frequency oscillators operating at millimetre-wave band

Analysis, modeling and simulation of ring resonators and their applications to filters and oscillators

Microstrip ring circuits have been extensively studied in the past three decades. A magnetic-wall model has been commonly used to analyze these circuits. Unlike the conventional magnetic-wall model, a simple transmission-line model, unaffected by boundary conditions, is developed to calculate the frequency modes of ring resonators of any general shape such as annular, square, or meander ring resonators. The new model can be used to extract equivalent lumped element circuits and unloaded Qs for both closed- and open-loop ring resonators. Several new bandpass filter structures, such as enhanced coupling, slow-wave, asymmetric-fed with two transmission zeros, and orthogonal direct-fed, have been proposed. These new proposed filters provide advantages of compact size, low insertion loss, and high selectivity. Also, an analytical technique is used to analyze the performance of the filters. The measured results show good agreement with the simulated results. A compact elliptic-function lowpass filter using microstrip stepped impedance hairpin resonators has been developed. The prototype filters are synthesized from the equivalent circuit model using available element-value tables. The filters are evaluated by experiment and simulation with good agreement. This simple equivalent circuit model provides a useful method to design and understand this type of filters and other relative circuits.Finally, a tunable feedback ring resonator oscillator using a voltage controlled piezoelectric transducer is introduced. The new oscillator is constructed by a ring resonator using a pair of orthogonal feed lines as a feedback structure. The ring resonator with two orthogonal feed lines can suppress odd modes and operate at even modes. A voltage controlled piezoelectric transducer is used to vary the resonant frequency of the ring resonator. This tuned oscillator operating at high oscillation frequency can be used in many wireless and sensor systems

Compensation technique for nonlinear distortion in RF circuits for multi-standard wireless systems

Recent technological advances in the RF and wireless industry has led to the design requirement of more sophisticated devices which can meet stringent specifications of bandwidth, data rate and throughput. These devices are required to be extremely sensitive and hence any external interference from other systems can severely affect the device and the output. This thesis introduces the existing problem in nonlinear components in a multi-standard wireless system due to interfering signals and suggests potential solution to the problem. Advances in RF and wireless systems with emerging new communication standards have made reconfigurablility and tunability a very viable option. RF transceivers are optimised for multi-standard operation, where one band of frequency can act as an interfering signal to the other band. Due to the presence of nonlinear circuits in the transceiver chains such as power amplifiers, reconfigurable and tunable filters and modulators, these interfering signals produce nonlinear distortion products which can deform the output signal considerably. Hence it becomes necessary to block these interfering signals using special components. The main objective of this thesis is to analyse and experimentally verify the nonlinear distortions in various RF circuits such as reconfigurable and tunable filters and devise ways to minimize the overall nonlinear distortion in the presence of other interfering signals. Reconfigurbality and tunablity in filters can be achieved using components such as varactor diodes, PIN diodes and optical switches. Nonlinear distortions in such components are measured using different signals and results noted. The compensation method developed to minimize nonlinear distortions in RF circuits caused due to interfering signals is explored thoroughly in this thesis. Compensation method used involves the design of novel microstrip bandstop filters which can block the interfering signals and hence give a clean output spectrum at the final stage. Recent years have seen the emergence of electronic band gap technology which has “band gap” properties meaning that a bandstop response is seen within particular range of frequency. This concept was utilised in the design of several novel bandstop filters using defected microstrip structure. Novel tunable bandstop filters has been introduced in order to block the unwanted signal. Fixed single-band and dual-band filters using DMS were fabricated with excellent achieved results. These filters were further extended to tunable structures. A dual-band tunable filter with miniaturized size was developed and designed. The designed filters were further used in the compensation technique where different scenarios showing the effect of interfering signals in wireless transceiver were described. Mathematical analysis proved the validation of the use of a bandstop filter as an inter-stage component. Distortion improvements of around 10dB have been experimentally verified using a power amplifier as device under test. Further experimental verification was carried out with a transmitter which included reconfigurable RF filters and power amplifier where an improvement of 15dB was achieved

Development of planar filters and diplexers for wireless transceiver front ends

The central theme of this work is the design of compact microstrip bandpass filters and diplexers and the investigation of applications of these circuits in integrated transceiver RF front-end. The core of this thesis therefore presents the following stages of the work: - Analysis of coupled pseudo-interdigital resonators and lines; formulation of approximate transmission zero conditions and the investigation of coupling between these two resonators and related structures. - Development of compact, low loss and high selectivity microstrip pseudointerdigital bandpass filters. The design procedure of the filter consists of three simple steps, starting from the design of a parallel-coupled bandpass filter using the image parameter method applied to coupled microstrip lines. The development of compact microstrip diplexers composed of these filters uses the optimized common-transformer diplexing technique. An experimental verification of the developed filters and diplexers is made. - Investigation of the use of stepped impedance resonators (SIR) for the design of pseudo-interdigital bandpass filters with advanced characteristics. The design of compact dual-band filter using SIR. The investigation of possible improvement of the stopband of bandpass filters using bandstop generating structures. The application of SIR, defected ground structures (DGS), spur-lines, and opencircuited stubs in the design of compact bandpass filters with improved stopband. - The application of the proposed filters and diplexers in the design of integrated antenna filters and antenna diplexers. Improvement of performance of patch antennas, such as suppression of spurious harmonics of single-band antenna and improvement of bandwidth and selectivity of dual-band antenna, as a result of integration with filters. Separation of antennas’ bands and reduction of component count in integrated antenna diplexer

Innovative Microwave and Millimetre-Wave Components and Sub-Systems Based on Substrate Integration Technology

RÉSUMÉ Avec le rapide développement des technologies microondes et millimétriques, les spécifications de conception des circuits et systèmes sont de plus en plus exigeantes. La tendance pour le développement des systèmes de communication se dirige vers un poids minimisé, une taille réduite, de multiples fonctions, une fiabilité accrue et un faible coût. Ainsi, des technologies microondes et millimétriques faibles coûts, performantes et convenant à une production de masse sont critiques pour développer avec succès des systèmes commerciaux. La technologie à guide d’ondes rectangulaire a toujours été parmi les plus populaires pour la fabrication des systèmes millimétriques. Cependant, une difficulté majeure est reliée à leur intégration avec des composants actifs et les autres types de lignes de transmission conventionnelles, telle que microruban ou coplanaire… Les technologies de Circuits Intégrés au Substrat (CISs), incluant la technologie Guide Intégré au Substrat (GIS), qui peut être intégrée dans les substrats diélectriques avec de faibles pertes d’insertion et de radiation, sont une famille de nouvelles structures à ondes guidées. Ces dernières permettent de faire un pont entre les structures planaires et non-planaires. Jusqu’à maintenant, les composants et les sous-systèmes micro-ondes basés sur la technologie GIS ont été largement étudiés et développés. Dans cette thèse, nous étudions d’avantage la technologie GIS afin de proposer et développer divers composants actif et passif micro-ondes et millimétriques innovant et originaux. Ces structures de composants innovants peuvent améliorer l’intégration entre les composants GIS et les autres composants planaires. Ainsi, un certain nombre de structures et composants sont proposés et appliqués dans la conception et la démonstration d’un réseau d’antennes intégré en ondes millimétriques et un sous-système d’antennes intelligentes à 60 GHz. Il est à noter que plusieurs composants étudiés dans ce travail ont été proposés et démontrés à des fréquences micro-ondes plus basses afin de faire une preuve de concept en permettant une fabrication facile des structures et des circuits. Ces circuits en basses fréquences peuvent facilement être adaptés pour des applications aux fréquences plus hautes.---------- ABSTRACT The tendency of modern microwave and millimetre-wave communication system development is towards small size, light weight, reliable, multifunctional and low-cost. Moreover, low-cost, mass producible, high-performance and high-yield microwave and millimetre wave technologies are crucial for developing successful commercial microwave and millimetre wave systems. Rectangular waveguide has always been among the most popular choices for the making of millimetre-wave circuits and systems. A major challenge, however, is related to its integration with active devices and other conventional planar transmission lines, such as microstrip or coplanar waveguide (CPW), etc. Substrate Integrated Circuits (SICs) techniques including substrate integrated waveguide (SIW), which can be integrated in planar dielectric substrate with low insertion loss, high Q and low radiation loss, present a family of novel guided wave structures. This scheme provides a bridge between planar and non-planar structures. Up to now, microwave components and sub-systems based on SIW technology have been widely studied and developed. In this thesis, we take a further study of SIW technology to propose and develop various innovative and original microwave and millimetre-wave passive and active components. These innovative component structures can improve the integration between SIW components and other planar components. Then, a certain number of proposed structures or components are applied in the design and demonstration of millimetre-wave integrated antenna arrays and 60 GHz smart antenna sub-system. Note that many components studied in this work were proposed and demonstrated at different lower microwave frequencies for the proof of concept purpose with easy-to-fabricate structures and circuits. Those low-frequency circuits can easily be scaled up for high-frequency applications

Design and analysis of a 6/4-GHz receiver front end

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1995.Includes bibliographical references (p. 133-136).by Feikai Sheu.M.Eng

Development of the ALMA-North America Sideband-Separating SIS Mixers

As the Atacama Large Millimeter/submillimeter Array (ALMA) nears completion, 73 dual-polarization receivers have been delivered for each of Bands 3 (84-116 GHz) and 6 (211-275 GHz). The receivers use sideband-separating superconducting Nb/Al-AlOx/Nb tunnel-junction (SIS) mixers, developed for ALMA to suppress atmospheric noise in the image band. The mixers were designed taking into account dynamic range, input return loss, and signal-to-image conversion (which can be significant in SIS mixers). Typical SSB receiver noise temperatures in Bands 3 and 6 are 30 K and 60 K, resp., and the image rejection is typically 15 dB.Comment: Submitted to IEEE Trans. Microwave Theory Tech., June 2013. 10 pages, 21 figure

Back-Action Evading Measurements of Nanomechanical Motion Approaching Quantum Limits

The application of quantum mechanics to macroscopic motion suggests many counterintuitive phenomena. While the quantum nature of the motion of individual atoms and molecules has long been successfully studied, an equivalent demonstration of the motion of a near-macroscopic structure remains a challenge in experimental physics. A nanomechanical resonator is an excellent system for such a study. It typically contains > 1010 atoms, and it may be modeled in terms of macroscopic parameters such as bulk density and elasticity. Yet it behaves like a simple harmonic oscillator, with mass low enough and resonant frequency high enough for its quantum zero-point motion and single energy quanta to be experimentally accessible. In pursuit of quantum phenomena in a mechanical oscillator, two important goals are to prepare the oscillator in its quantum ground state, and to measure its position with a precision limited by the Heisenberg uncertainty principle. In this work we have demonstrated techniques that advance towards both of these goals. Our system comprises a 30 micron × 170 nm, 2.2 pg, 5.57 MHz nanomechanical resonator capacitively coupled to a 5 GHz superconducting microwave resonator. The microwave resonator and nanomechanical resonator are fabricated together onto a single silicon chip and measured in a dilution refrigerator at temperatures below 150 mK. At these temperatures the coupling of the motion to the thermal environment is very small, resulting in a very high mechanical Q, approaching ∼ 106. By driving with a microwave pump signal, we observed sidebands generated by the mechanical motion and used these to measure the thermal motion of the resonator. Applying a pump tone red-detuned from the microwave resonance, we used the microwave field to damp the mechanical resonator, extracting energy and "cooling" the motion in a manner similar to optical cooling of trapped atoms. Starting from a mode temperature of ∼ 150 mK, we reached ∼ 40 mK by this "backaction cooling" technique, corresponding to an occupation factor only ∼ 150 times above the ground state of motion. We also determined the precision of our device in measurement of position. Quantum mechanics dictates that, in a continuous position measurement, the precision may be no better than the zero-point motion of the resonator. Increasing the coupling of the resonator to detector will eventually result in back-action driving of the motion, adding imprecision and enforcing this limit. We demonstrated that our system is capable of precisions approaching this limit, and identified the primary experimental factors preventing us from reaching it: noise added to the measurement by our amplifier, and excess dissipation appearing in our microwave resonator at high pump powers. Furthermore, by applying both red- and blue-detuned phase-coherent microwave pump signals, we demonstrated back-action evading (BAE) measurement sensitive to only a single quadrature of the motion. By avoiding the back-action driving in the measured quadrature, such a technique has the potential for precisions surpassing the limit of the zero-point motion. With this method, we achieved a measurement precision of ∼ 100 fm, or 4 times the quantum zero-point motion of the mechanical resonator. We found that the measured quadrature is insensitive to back-action driving by at least a factor of 82 relative to the unmeasured quadrature. We also identified a mechanical parametric amplification effect which arises during the BAE measurement. This effect sets limits on the BAE performance but also mechanically preamplifies the motion, resulting in a position resolution 1.3 times the zero-point motion. We discuss how to overcome the experimental limits set by amplifier noise, pump power and parametric amplification. These results serve to define the path forward for demonstrating truly quantum-limited measurement and non-classical states of motion in a nearly-macroscopic object