A Survey of Non-conventional Techniques for Low-voltage Low-power Analog Circuit Design

Designing integrated circuits able to work under low-voltage (LV) low-power (LP) condition is currently undergoing a very considerable boom. Reducing voltage supply and power consumption of integrated circuits is crucial factor since in general it ensures the device reliability, prevents overheating of the circuits and in particular prolongs the operation period for battery powered devices. Recently, non-conventional techniques i.e. bulk-driven (BD), floating-gate (FG) and quasi-floating-gate (QFG) techniques have been proposed as powerful ways to reduce the design complexity and push the voltage supply towards threshold voltage of the MOS transistors (MOST). Therefore, this paper presents the operation principle, the advantages and disadvantages of each of these techniques, enabling circuit designers to choose the proper design technique based on application requirements. As an example of application three operational transconductance amplifiers (OTA) base on these non-conventional techniques are presented, the voltage supply is only ±0.4 V and the power consumption is 23.5 µW. PSpice simulation results using the 0.18 µm CMOS technology from TSMC are included to verify the design functionality and correspondence with theory

Fractionally-addressed delay lines

While traditional implementations of variable-length digital delay lines are based on a circular buffer accessed by two pointers, we propose an implementation where a single fractional pointer is used both for read and write operations. On modern general-purpose architectures, the proposed method is nearly as efficient as the popularinterpolated circular buffer, and it behaves well for delay-length modulations commonly found in digital audio effects. The physical interpretation of the new implementation shows that it is suitable for simulating tension or density modulations in wave-propagating media.Comment: 11 pages, 19 figures, to be published in IEEE Transactions on Speech and Audio Processing Corrected ACM-clas

Optimization of Short-Channel RF CMOS Low Noise Amplifiers by Geometric Programming

Geometric programming (GP) is an optimization method to produce globally optimal circuit parameters with high computational efficiency. Such a method has been applied to short-channel (90 nm and 180 nm) CMOS Low Noise Amplifiers (LNAs) with common-source inductive degeneration to obtain optimal design parameters by minimizing the noise figure. An extensive survey of analytical models and experimental results reported in the literature was carried out to quantify the issue of excessive thermal noise for short-channel MOSFETs. Geometric programming compatible functions have been determined to calculate the noise figure of short-channel CMOS devices by taking into consideration channel-length modulation and velocity saturation effects

On the VCO/Frequency Divider Interface in Cryogenic CMOS PLL for Quantum Computing Applications

The availability of quantum microprocessors is mandatory, to efficiently run those quantum al-gorithms promising a radical leap forward in computation capability. Silicon-based nanostruc-tured qubits appear today as a very interesting approach, because of their higher information density, longer coherence times, fast operation gates, and compatibility with the actual CMOS technology. In particular, thanks to their phase noise properties, the actual CMOS RFIC Phase-Locked Loops (PLL) and Phase-Locked Oscillators (PLO) are interesting circuits to synthe-size control signals for spintronic qubits. In a quantum microprocessor, these circuits should op-erate close to the qubits, that is, at cryogenic temperatures. The lack of commercial cryogenic Design Kits (DK) may make the interface between the Voltage Controlled Oscillator (VCO) and the Frequency Divider (FD) a serious issue. Nevertheless, currently this issue has not been sys-tematically addressed in the literature. The aim of the present paper is to investigate the VCO/FD interface when the temperature drops from room to cryogenic. To this purpose, physi-cal models of electronics passive/active devices and equivalent circuits of VCO and the FD were developed at room and cryogenic temperatures. The modeling activity has led to design guide-lines for the VCO/FD interface, useful in the absence of cryogenic DKs

Very large time constant Gm-C Filters

In this study a set of tools for the design of fully integrated transconductor-capacitor (Gm-C) filters, with very large time constants and current consumption under one micro-Ampere are presented. The selected application is a 2nd order bandpass-filter-amplifier, with a gain of 400 from 0.5 to 7Hz, carrying out the signal conditioning of a piezoelectric accelerometer which is part of an implantable cardiac pacemaker. The main challenge is to achieve very large time constants, without using any discrete external component. The chosen circuit technique to fulfill the requirement is series-parallel current division applied to standard symmetrical transconductors (OTAs). These circuits have demonstrated to be an excellent solution regarding their occupied area, power consumption, noise, linearity, and particularly offset. OTAs as low as 33pS -equivalent to a 30G resistor-, with up to 1V linear range, and input referred offset of a few mV, were designed, fabricated in a standard 0.8 micron CMOS technology, and tested. The application requires the series-parallel association of a large number of transistors, and the use of bias currents as low as a few pico-Amperes, which is not very common in analog integrated circuits. In this case the designer should employ maximum care in the selection of the transistor models to be used. A central aspect of this thesis was also to evaluate and develop noise and offset estimation models which was not obvious in the very beginning of the research. In the first two chapters an introduction to the target application is presented, and several MOS transistor characteristics in terms of the inversion coefficient -using the ACM transistor model- are evaluated. In chapter 3 it is discussed whether the usual flicker and thermal noise models are consistent regarding series-parallel association, and adequately represent the expected noise behavior under different bias conditions. A consistent, physics-based, one-equation-all-regions model for flicker noise in the MOS transistor is then presented. Several noise measurements are included demonstrating that the new model accurately fits widely different bias situations. A new model for mismatch offset in MOS transistors is presented, as a corollary of the flicker noise analysis. Finally, the correlation between flicker noise and mismatch offset, that can be seen as a DC noise, is shown. In chapter 4, the design of OTAs with an extended linear range, and very low transconductance, using series-parallel current division is presented. Precise tools are introduced for the estimation of noise and mismatch offset in series-parallel current mirrors, that are shown to help in the reduction of inaccuracies in the copy of currents with a large copy factor. The design and measurement of several OTA examples are presented. In chapter 5, the developed tools, and the OTAs shown, are employed in the design of the above mentioned filter for the piezoelectric accelerometer. A general methodology for the design of Gm-C filters with similar characteristics is established. The filter was fabricated and tested, successfully operating with a total power consumption of 233nA, up to a 2V power supply, with an input noise and mismatch offset of 2-4 Vrms, and 18 V respectively. To summarize the main results obtained were: The development of a new flicker noise model, the study of the effect of mismatch regarding series-parallel association, a new design methodology for OTAs and Gm-C filters. It is our hope that this constitutes a helpful set of tools for the circuit designer.En esta tesis se presenta un conjunto de herramientas para el diseño de circuitos integrados que implementan filtros transconductor-capacitor (Gm-C), de muy altas constantes de tiempo, con bajo ruido, y consumo de corriente por debajo del micro-Ampere. Como ejemplo de aplicación se toma un amplificador-pasabanda 2º orden, de ganancia 400 en la banda de 0.5 a 7Hz, que realiza el acondicionamiento de señal de un acelerómetro piezoeléctrico a ser empleado en un marcapasos implantable. El principal desafío es realizar en dicho filtro de tiempo continuo, muy altas constantes de tiempo sin usar componentes externos. La técnica elegida para alcanzar tal objetivo es la división serie-paralelo de corriente en transconductores (OTAs) simétricos estándar. Estos circuitos demostraron ser una excelente solución en cuanto al área ocupada, su consumo, ruido, linealidad, y en particular offset. Se diseñaron, fabricaron, y midieron, OTAs hasta 33pS -equivalente a una resistencia de 30G -, con hasta 1V de rango de lineal, y offset a la entrada de algunos mV, utilizando una tecnología CMOS de 0.8 micras de largo mínimo de canal. La aplicación requiere la asociación serie-paralelo de un gran número de transistores, y polarización con corrientes de hasta pico-Amperes, lo que constituye una situación poco frecuente en circuitos integrados analógicos. En este marco el diseñador debe elegir los modelos de transistor con sumo cuidado. Un aspecto central de esta tesis es también, el estudio y presentación de modelos adecuados de ruido y offset, que no resultan obvios al principio. En los primeros dos capítulos se realiza una introducción y se revisa, utilizando el modelo ACM, diferentes características del transistor MOS en función del nivel de inversión. En el capítulo 3 revisa la pertinencia y consistencia frente a la asociación serie-paralelo, de los modelos usuales de ruido de flicker o 1/f, y térmico. Luego se presenta, incluyendo medidas, un nuevo modelo físico, consistente, simple, y válido en todas las regiones de operación del transistor MOS, para el ruido de flicker. Como corolario a este estudio se presenta un nuevo modelo para estimar el desapareo entre transistores, en función no solo de la geometría, pero también de la polarización. Se demuestra la correlación, debido a su origen físico análogo, entre el ruido de flicker y el offset por desapareo que puede ser visto como un ruido en DC. En el capítulo 4 se presenta el diseño de OTAs con rango de linealidad extendido, y muy baja transconductancia, utilizando división serie-paralelo de corriente. Se presentan herramientas precisas para la estimación de offset y ruido y se demuestra la utilidad de la técnica para reducir el offset en espejos de corriente. Se presenta el diseño y medida de diversos OTAs. En el capítulo 5, las herramientas desarrolladas, y los OTAs presentados, son empleados en el diseño del filtro descripto para un acelerómetro piezoeléctrico. Se establece una metodología general para el diseño de filtros Gm-C con características similares. El filtro se fabricó y midió, operando en forma satisfactoria, con un consumo total de 230nA y hasta los 2V de tensión de alimentación, con ruido y offset a la entrada de tan solo 2-4 Vrms, y 18 V respectivamente. El desarrollo de un nuevo modelo de ruido 1/f para el transistor MOS, el estudio de la influencia del offset frente a la asociación serie-paralelo y su aplicación en OTAs, la metodología de diseño empleada, la demostración del uso de técnicas novedosas en una aplicación como la elegida que tiene relevancia tecnológica e interés académico; esperamos que todo ello constituya una contribución valiosa para la comunidad científica en microelectrónica y un conjunto de herramientas de utilidad para el diseño de circuitos

A study of Radiation-Tolerant Voltage-Controlled Oscillators designs in 65 nm bulk and 28 nm FDSOI CMOS technologies

Phase-locked loop (PLL) systems are widely employed in integrated circuits for space analog devices and communications systems that operate in radiation environments, where significant perturbations, especially in terms of phase noise, can be generated due to radiation particles. Among all the blocks that form a PLL system, previous research suggests the voltage-controlled oscillator (VCO) is one of the most critical components in terms of radiation tolerance and electric performance. Ring oscillators (ROs) and LC-tank VCOs have been commonly employed in high-performance PLLs. Nevertheless, both structures have drawbacks including a limited tuning range, high sensitivity to phase noise, limited radiation tolerance, and large design areas. In order to fulfill these high-performance requirements, a current-model logic (CML) based RO-VCO is presented as a possible solution capable of reducing the limitations of the commonly used structures and exploiting their advantages. The proposed hybrid VCO model includes passive components in its design which are the key parameters that define oscillation frequency of this structure. This tunable oscillator has been designed and tested in 65nm Bulk and 28 nm Fully depleted silicon-on-insulator (FDSOI) CMOS technologies The 65nm testchip was designed to compare the behavior of the proposed CML VCO with a current-starved RO and a radiation hardened by design (RHBD) LC-tank VCO in terms of tuning range, phase noise, Single event effect (SEE) sensitivity and design area. Simulations were carried out by applying a double exponential current pulse into different sensitive nodes of the three VCOs. In addition, SEE tests were conducted using pulsed laser experiments. Simulation and test results show that a CML VCO can effectively overcome the limitations presented by a RO-VCO and LC-tank VCO, achieving a wide range of tuning, and low sensitivity to noise and SEEs without the need for a large cross-section. Further studies of the proposed CML VCO were done on 28nm FDSOI in order to reduce the leakage current and increase the switching speed. the same current-starved VCO and CML VCO were implemented on this testchip, and simulations were performed by injecting a double exponential current pulse energy into the previously defined sensitive nodes. The results show SEE sensitivity improvement without narrowing the tuning range or affecting the phase noise response

Design of an adaptive cable equalizer using 0.5 [mu]m [i.e. micrometer] CMOS process

Data transmitted over a long length of cable at high rates must be equalized in order to compensate for the loss and phase dispersion of the cable. The more the cable length, the more the loss is in it. As the data transfer rate is increasing, more bandwidth is needed and the data communication industries are demanding an equalizer system with more bandwidth. A pole-zero model for the coax cable- equalizer is developed which shows that the poles and zeros of the cable transfer function decrease linearly with the increase of the cable length. Thus an adaptive equalizer system has been designed where the length of the cable will be estimated through the peak detector circuitry and the equalizer filter will be tuned automatically according to the estimated cable length using this linearity. All the circuits of the system have been designed using AMI 0.5µm CMOS technology and simulated on Cadence\u27s Spectre tools