Design and Implementation of a Micro-Inverter for Photovoltaic Applications

The objective of this work is to design and build a novel topology of a micro-inverter to directly convert DC power from a photovoltaic module to AC power. In the proposed micro-inverter, a structure with two power stages, which are DC/DC and then DC/AC converters, is used. A novel MPPT algorithm is implemented and evaluated in the DC/DC converter to optimize the solar panel energy production. The new method operates with an efficiency of 97.9%, which is a 1% improvement on the standard method, and a response time of In this research, the following approach is taken. A literature review was conducted, to identify potential converter topologies. A topology for both converters was selected by comparison of performance through simulations. Maximum Power Point Tracking algorithms were also investigated, to select an appropriate control scheme. A design for two converters was then performed, leading to a prototype for experimental verificatio

A review and classification of LED ballasts

This paper presents a review on existing ballasts for light-emitting diodes (LED) with considerations to their compliance to regulations, technological challenges, and on meeting various application requirements. All existing LED ballasts, including those proposed in recent literature, have been appropriately classified and systematically organized for the discussion. The dissemination of this information and its understanding is helpful for future R&D pursuits in this area. © 2013 IEEE.published_or_final_versio

Design and Analysis of High Frequency Power Converters for Envelope Tracking Applications

In the field of power electronics, designers are constantly researching new methods to improve efficiency while optimizing dynamic performance. As communication technologies progress we are more often dealing with systems of increasing speed and complexity. For instance, from 1991 to 2013 we have observed the mobile broadband communication sector evolve from ~230 Kbits/s (2G) speeds to ~100 Mbits/s (4G LTE), a 430% increase in communication speed. In contrast, we have not observed the same evolutionary development in industrial power converters. Most switch-mode power supplies are still manufactured for 100 KHz to 800 KHz operating frequencies. The main reason for this is that most electrical devices only require steady-state DC power, so high speed conversion performance is largely unnecessary. But as size expectations for portable electronic devices continue to decrease, the only way to meet future demand is to realize power electronics that operate at much higher switching frequencies. Furthermore there is increasing demand to improve the transient response requirements in processor-based systems and achieve practical envelope tracking in RF communication systems. The most straightforward method of increasing the dynamic response for these systems is to increase the switching frequency of the power electronics in a sustainable and coherent manner

Design and implementation of synchronous buck converter based PV energy system for battery charging applications

The Photo Voltaic (PV) energy system is a very new concept in use, which is gaining popularity due to increasing importance to research on alternative sources of energy over depletion of the conventional fossil fuels world-wide. The systems are being developed to extract energy from the sun in the most efficient manner and suit them to the available loads without affecting their performance. In this project, synchronous buck converter based PV energy system for portable applications; especially low power device applications such as charging mobile phone batteries are considered. Here, the converter topology used uses soft switching technique to reduce the switching losses which is found prominently in the conventional buck converter, thus efficiency of the system is improved and the heating of MOSFETs due to switching losses reduce and the MOSFETs have a longer life. The DC power extracted from the PV array is synthesized and modulated by the converter to suit the load requirements. Further, the comparative study between the proposed synchronous buck converter and the conventional buck converter is analysed in terms of efficiency improvement and switching loss reduction. The proposed system is simulated in the MATLAB-Simulink environment and the practical implementation of the proposed converter is done to validate the theoretical results. Open-loop control of synchronous buck converter based PV energy system is realised through ICs and experimental results were observed

Design of a low-voltage low-power dc-dc HF converter

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2008.Includes bibliographical references (p. 230-234).Many portable electronic applications could benefit from a power converter able to achieve high efficiency across wide input and output voltage ranges at a small size. However, it is difficult for many conventional power converter designs to provide wide operation range while maintaining high efficiency, especially if both up-and-down voltage conversion is to be achieved. Furthermore, the bulk energy storage required at contemporary switching frequencies of a few megahertz and below limits the degree of miniaturization that can be achieved and hampers fast transient response. Therefore, design methods that reduce energy storage requirements and expand efficient operation range are desirable. This thesis focuses on the development of a High Frequency (HF) dc-dc SEPIC converter exploiting resonant switching and gating with fixed frequency control techniques to achieve these goals. The proposed approach provides high efficiency over very wide input and output voltage ranges and power levels. It also provides up-and-down conversion, and requires little energy storage which allows for excellent transient response. The proposed design strategies are discussed in the context of a prototype converter operating over wide input voltage (3.6 - 7.2V), output voltage (3 - 9V) and power (0.3 - 3W) ranges. The 20MHz converter prototype, utilizing commercial vertical MOSFETs, takes advantage of a quasi-resonant SEPIC topology and resonant gating technique to provide good efficiency across the wide operating ranges required. The converter efficiency stays above 80% across the entire input voltage range at the nominal output voltage. The closed-loop performance is demonstrated via an implementation of a PWM on-off control scheme, illustrating the salient characteristics in terms of additional control circuitry power dissipation and transient response.by Jingying Hu.S.M