High-Density Solid-State Memory Devices and Technologies

This Special Issue aims to examine high-density solid-state memory devices and technologies from various standpoints in an attempt to foster their continuous success in the future. Considering that broadening of the range of applications will likely offer different types of solid-state memories their chance in the spotlight, the Special Issue is not focused on a specific storage solution but rather embraces all the most relevant solid-state memory devices and technologies currently on stage. Even the subjects dealt with in this Special Issue are widespread, ranging from process and design issues/innovations to the experimental and theoretical analysis of the operation and from the performance and reliability of memory devices and arrays to the exploitation of solid-state memories to pursue new computing paradigms

Cost-Effective TSV Grouping for Yield Improvement of 3D-ICs

Three-dimensional Integrated Circuits (3D-ICs) vertically stack multiple silicon dies to reduce overall wire length, power consumption, and allow integration of heterogeneous technologies. Through-silicon-vias (TSVs) which act as vertical links between layers pose challenges for 3D integration design. TSV defects can happen in fabrication process and bonding stage, which can reduce the yield and increase the cost. Recent work proposed the employment of redundant TSVs to improve the yield of 3D-ICs. This paper presents a redundant TSVs grouping technique, which partition regular and redundant TSVs into groups. For each group, a set of multiplexers are used to select good signal paths away from defective TSVs. We investigate the impact of grouping ratio (regular-to-redundant TSVs in one group) on trade-off between yield and hardware overhead. We also show probabilistic models for yield analysis under the influence of independent and clustering defect distributions. Simulation results show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratios lead to achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios

Variation-Tolerant Non-Uniform 3D Cache Management in Memory Stacked Multi-Core Processors

Process variations in integrated circuits have significant impact on their performance, leakage and stability. This is particularly evident in large, regular and dense structures such as DRAMs. DRAMs are built using minimized transistors with presumably uniform speed in an organized array structure. Process variation can introduce latency disparity among different memory arrays. With the proliferation of 3D stacking technology, DRAMs become a favorable choice for stacking on top of a multi-core processor as a last level cache for large capacity, high bandwidth, and low power. Hence, variations in bank speed create a unique problem of non-uniform cache accesses in the 3D space.In this thesis, we investigate cache management techniques for tolerating process variation in a 3D DRAM stacked onto a multi-core processor. We modeled the process variation in a 4-layer DRAM memory to characterize the latency variations among different banks. As a result, the notion of fast and slow banks from the core's standpoint is no longer associated with their physical distances with the banks. They are determined by the different bank latencies due to process variation. We develop cache migration schemes that utilize fast banks while limiting the cost due to migration. Our experiments show that there is a great performance benefit in exploiting fast memory banks through migration. On average, a variation-aware management can improve the performance of a workload over the baseline (where the speed of the slowest bank is assumed for all banks) by 17.8%. We are also only 0.45% away in performance from an ideal memory where no PV is present

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Characterization and Implementation of Fault-Tolerant Vertical Links for 3-D Networks-on-Chip

Through silicon vias (TSVs) provide an efficient way to support vertical communication among different layers of a vertically stacked chip, enabling scalable 3-D networks-on-chip (NoC) architectures. Unfortunately, low TSV yields significantly impact the feasibility of high-bandwidth vertical connectivity. In this paper, we present a semi-automated design flow for 3-D NoCs including a defect-tolerance scheme to increase the global yield of 3-D stacked chips. Starting from an accurate physical and geometrical model of TSVs: 1) we extract a circuit-level model for vertical interconnections; 2) we use it to evaluate the design implications of extending switch architectures with ports in the vertical direction; moreover, 3) we present a defect-tolerance technique for TSV-based multi-bit links through an effective use of redundancy; and finally, 4) we present a design flow allowing for post-layout simulation of NoCs with links in all three physical dimensions. Experimental results show that a 3-D NoC implementation yields around 10% frequency improvement over a 2-D one, thanks to the propagation delay advantage of TSVs and the shorter links. In addition, the adopted fault tolerance scheme demonstrates a significant yield improvement, ranging from 66% to 98%, with a low area cost (20.9% on a vertical link in a NoC switch, which leads a modest 2.1% increase in the total switch area) in 130 nm technology, with minimal impact on very large-scale integrated design and test flows

Design for pre-bond testability in 3D integrated circuits

In this dissertation we propose several DFT techniques specific to 3D stacked IC systems. The goal has explicitly been to create techniques that integrate easily with existing IC test systems. Specifically, this means utilizing scan- and wrapper-based techniques, two foundations of the digital IC test industry. First, we describe a general test architecture for 3D ICs. In this architecture, each tier of a 3D design is wrapped in test control logic that both manages tier test pre-bond and integrates the tier into the large test architecture post-bond. We describe a new kind of boundary scan to provide the necessary test control and observation of the partial circuits, and we propose a new design methodology for test hardcore that ensures both pre-bond functionality and post-bond optimality. We present the application of these techniques to the 3D-MAPS test vehicle, which has proven their effectiveness. Second, we extend these DFT techniques to circuit-partitioned designs. We find that boundary scan design is generally sufficient, but that some 3D designs require special DFT treatment. Most importantly, we demonstrate that the functional partitioning inherent in 3D design can potentially decrease the total test cost of verifying a circuit. Third, we present a new CAD algorithm for designing 3D test wrappers. This algorithm co-designs the pre-bond and post-bond wrappers to simultaneously minimize test time and routing cost. On average, our algorithm utilizes over 90% of the wires in both the pre-bond and post-bond wrappers. Finally, we look at the 3D vias themselves to develop a low-cost, high-volume pre-bond test methodology appropriate for production-level test. We describe the shorting probes methodology, wherein large test probes are used to contact multiple small 3D vias. This technique is an all-digital test method that integrates seamlessly into existing test flows. Our experimental results demonstrate two key facts: neither the large capacitance of the probe tips nor the process variation in the 3D vias and the probe tips significantly hinders the testability of the circuits. Taken together, this body of work defines a complete test methodology for testing 3D ICs pre-bond, eliminating one of the key hurdles to the commercialization of 3D technology.PhDCommittee Chair: Lee, Hsien-Hsin; Committee Member: Bakir, Muhannad; Committee Member: Lim, Sung Kyu; Committee Member: Vuduc, Richard; Committee Member: Yalamanchili, Sudhaka

Self-Aligned 3D Chip Integration Technology and Through-Silicon Serial Data Transmission

The emerging three-dimensional (3D) integration technology is expected to lead to an industry paradigm shift due to its tremendous benefits. Intense research activities are going on about technology, simulation, design, and product prototypes. This thesis work aims at fabricating through-silicon vias (TSVs) on diced processor chips, and later bonding them into a 3D-stacked chip. How to handle and process delicate processor chips with high alignment precision is a key issue. The TSV process to be developed also needs to adapt to this constraint. Four TSV processes have been studied. Among them, the ring-trench TSV process demonstrates the feasibility of fabricating TSVs with the prevailing dimensions, and the whole-through TSV process achieves the first dummy chip post-processed with TSVs in EPFL although the dimension is rather large to keep a reasonable aspect ratio (AR). Four self-alignment (SA) techniques have been investigated, among which the gravitational SA and the hydrophobic SA are found to be quite promising. Using gravitational SA, we come to the conclusion that cavities in silicon carrier wafer with a profile angle of 60° can align the chips with less than 20 µm inaccuracies. The alignment precision can be improved after adopting more advanced dicing tools instead of using the traditional dicing saws and larger cavity profile angle. Such inaccuracy will be sufficient to align the relatively large TSVs for general products such as 3D image sensors. By fabricating bottom TSVs in the carrier wafer, a 3D silicon interposer idea has been proposed to stack another chip, e.g. a processor chip, on the other side of the carrier wafer. But stacking microprocessor chips fabricated with TSVs will require higher alignment precision. A hydrophobic SA technique using the surface tension force generated by the water-to-air interfaces around the pads can greatly reduce the alignment inaccuracy to less than 1 µm. This low-cost and high throughput SA procedure is processed in air, fully-compatible with current fabrication technologies, and highly stable and repeatable. We present a theoretical meniscus model to predict SA results and to provide the design rules. This technique is quite promising for advanced 3D applications involving logic and heterogeneous stacking. As TSVs' dimensions in the chip-level 3D integration are constrained by the chip-level processes, such as bonding, the smallest TSVs might still be about 5 µm. Thus, the area occupied by the TSVs cannot be neglected. Fortunately, TSVs can withstand very high bandwidths, meaning that data can be serialized and transmitted using less numbers of TSVs. With 20 µm TSVs, the 2-Gb/s 8:1 serial link implemented saves 75% of the area of its 8-bit parallel counterpart. The quasi-serial link proposed can effectively balance the inter-layer bandwidth and the serial links' area consumption. The area model of the serial or quasi-serial links working under higher frequencies provides some guidelines to choose the proper serial link design, and it also predicts that when TSV diameter shrinks to 5 µm, it will be difficult to keep this area benefit if without some novel circuit design techniques. As the serial links can be implemented with less area, the bandwidth per unit area is increased. Two scenarios are studied, single-port memory access and multi-port memory access. The expanded inter-layer bandwidth by serialization does not improve the system performance because of the bus-bottleneck problem. In the latter scenario, the inter-layer ultra-wide bandwidth can be exploited as each memory bank can be accessed randomly through the NoC. Thus further widening the inter-layer bandwidth through serialization, the system performance will be improved

On Energy Efficient Computing Platforms

In accordance with the Moore's law, the increasing number of on-chip integrated transistors has enabled modern computing platforms with not only higher processing power but also more affordable prices. As a result, these platforms, including portable devices, work stations and data centres, are becoming an inevitable part of the human society. However, with the demand for portability and raising cost of power, energy efficiency has emerged to be a major concern for modern computing platforms. As the complexity of on-chip systems increases, Network-on-Chip (NoC) has been proved as an efficient communication architecture which can further improve system performances and scalability while reducing the design cost. Therefore, in this thesis, we study and propose energy optimization approaches based on NoC architecture, with special focuses on the following aspects. As the architectural trend of future computing platforms, 3D systems have many bene ts including higher integration density, smaller footprint, heterogeneous integration, etc. Moreover, 3D technology can signi cantly improve the network communication and effectively avoid long wirings, and therefore, provide higher system performance and energy efficiency. With the dynamic nature of on-chip communication in large scale NoC based systems, run-time system optimization is of crucial importance in order to achieve higher system reliability and essentially energy efficiency. In this thesis, we propose an agent based system design approach where agents are on-chip components which monitor and control system parameters such as supply voltage, operating frequency, etc. With this approach, we have analysed the implementation alternatives for dynamic voltage and frequency scaling and power gating techniques at different granularity, which reduce both dynamic and leakage energy consumption. Topologies, being one of the key factors for NoCs, are also explored for energy saving purpose. A Honeycomb NoC architecture is proposed in this thesis with turn-model based deadlock-free routing algorithms. Our analysis and simulation based evaluation show that Honeycomb NoCs outperform their Mesh based counterparts in terms of network cost, system performance as well as energy efficiency.Siirretty Doriast