Power Beacon’s deployment optimization for wirelessly powering massive Internet of Things networks

Abstract. The fifth-generation (5G) and beyond wireless cellular networks promise the native support to, among other use cases, the so-called Internet of Things (IoT). Different from human-based cellular services, IoT networks implement a novel vision where ordinary machines possess the ability to autonomously sense, actuate, compute, and communicate throughout the Internet. However, as the number of connected devices grows larger, an urgent demand for energy-efficient communication technologies arises. A key challenge related to IoT devices is that their very small form factor allows them to carry just a tiny battery that might not be even possible to replace due to installation conditions, or too costly in terms of maintenance because of the massiveness of the network. This issue limits the lifetime of the network and compromises its reliability. Wireless energy transfer (WET) has emerged as a potential candidate to replenish sensors’ batteries or to sustain the operation of battery-free devices, as it provides a controllable source of energy over-the-air. Therefore, WET eliminates the need for regular maintenance, allows sensors’ form factor reduction, and reduces the battery disposal that contributes to the environment pollution. In this thesis, we review some WET-enabled scenarios and state-of-the-art techniques for implementing WET in IoT networks. In particular, we focus our attention on the deployment optimization of the so-called power beacons (PBs), which are the energy transmitters for charging a massive IoT deployment subject to a network-wide probabilistic energy outage constraint. We assume that IoT sensors’ positions are unknown at the PBs, and hence we maximize the average incident power on the worst network location. We propose a linear-time complexity algorithm for optimizing the PBs’ positions that outperforms benchmark methods in terms of minimum average incident power and computation time. Then, we also present some insights on the maximum coverage area under certain propagation conditions

Wireless Power Transfer in Distributed Antenna Systems

This paper studies the performance of wireless power transfer in distributed antenna systems (DAS). In particular, the distributed remote radio heads (RRHs), which are conventionally distributed in the network to enhance the performance, are also used to increase the energy harvesting (EH) at the energy-constrained users. Based on this idea, the network area is divided into two zones, namely, A) EH zone and B) Interference zone. The users in the EH zones are guaranteed to harvest sufficient energy from the closed RRH, while the users in the interference zones harvest energy from the surrounding RRHs. A harvest-then-transmit protocol is adopted, where in the power transfer phase the multiple antennas RRHs broadcast energy signals to the users. In the information transmission phase, the users utilize the harvested energy to transmit their signals to the RRHs. In addition, zero-forcing is applied at the RRHs receivers, to mitigate the interference. The system spectral efficiency is evaluated in two different scenarios based on the channel state information (CSI), namely: 1) CSI is unknown at the RRHs; 2) CSI is perfectly known at the RRHs. In contrast to conventional EH-muliple input multiple output (MIMO) systems, performance analysis of EH DAS-MIMO is a challenging problem, because the channels are characterized by non-identical path-loss and EH effects which make the classical analytical methods nontractable. In light of this, new analytical expressions of the ergodic spectral efficiency are derived, and then Monte-Carlo simulations are provided to verify the accuracy of our analysis. The effects of main system parameters on the EH-DAS performance are investigated. The results show that there is an optimal value of the EH time for each users locations that maximizes the system performance. In addition, size of the EH-zone area depends on the required harvested power at the users which is dependent essentially on the target spectral efficiency

An IoT-Aware Smart System Exploiting the Electromagnetic Behavior of UHF-RFID Tags to Improve Worker Safety in Outdoor Environments

Recently, different solutions leveraging Internet of Things (IoT) technologies have been adopted to avoid accidents in agricultural working environments. As an example, heavy vehicles, e.g., tractors or excavators, have been upgraded with remote controls. Nonetheless, the community continues to encourage discussions on safety issues. In this framework, a localization system installed on remote-controlled farm machines (RCFM) can help in preventing fatal accidents and reduce collision risks. This paper presents an innovative system that exploits passive UHF-RFID technology supported by commercial BLE Beacons for monitoring and preventing accidents that may occur when ground-workers in RCFM collaborate in outdoor agricultural working areas. To this aim, a modular architecture is proposed to locate workers, obstacles and machines and guarantees the security of RCFM movements by using specific notifications for ground-workers prompt interventions. Its main characteristics are presented with its main positioning features based on passive UHF-RFID technology. An experimental campaign discusses its performance and determines the best configuration of the UHF-RFID tags installed on workers and obstacles. Finally, system validation demonstrates the reliability of the main components and the usefulness of the proposed architecture for worker safety

Internet of Things in Agricultural Innovation and Security

The agricultural Internet of Things (Ag-IoT) paradigm has tremendous potential in transparent integration of underground soil sensing, farm machinery, and sensor-guided irrigation systems with the complex social network of growers, agronomists, crop consultants, and advisors. The aim of the IoT in agricultural innovation and security chapter is to present agricultural IoT research and paradigm to promote sustainable production of safe, healthy, and profitable crop and animal agricultural products. This chapter covers the IoT platform to test optimized management strategies, engage farmer and industry groups, and investigate new and traditional technology drivers that will enhance resilience of the farmers to the socio-environmental changes. A review of state-of-the-art communication architectures and underlying sensing technologies and communication mechanisms is presented with coverage of recent advances in the theory and applications of wireless underground communications. Major challenges in Ag-IoT design and implementation are also discussed

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

Beam scanning by liquid-crystal biasing in a modified SIW structure

A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium