Analysis and Comparison of Clothoid and Dubins Algorithms for UAV Trajectory Generation

The differences between two types of pose-based UAV path generation methods clothoid and Dubins are analyzed in this thesis. The Dubins path is a combination of circular arcs and straight line segments; therefore its curvature will exhibit sudden jumps between constant values. The resulting path will have a minimum length if turns are performed at the minimum possible turn radius. The clothoid path consists of a similar combination of arcs and segments but the difference is that the clothoid arcs have a linearly variable curvature and are generated based on Fresnel integrals. Geometrically, the generation of the clothoid arc starts with a large curvature that decreases to zero. The clothoid path results are longer than the Dubins path between the same two poses and for the same minimum turn radius. These two algorithms are the focus of this research because of their geometrical simplicity, flexibility, and low computational requirements.;The comparison between clothoid and Dubins algorithms relies on extensive simulation results collected using an ad-hoc developed automated data acquisition tool within the WVU UAV simulation environment. The model of a small jet engine UAV has been used for this purpose. The experimental design considers several primary factors, such as different trajectory tracking control laws, normal and abnormal flight conditions, relative configuration of poses, and wind and turbulence. A total of five different controllers have been considered, three conventional with fixed parameters and two adaptive. The abnormal flight conditions include locked or damaged actuators (stabilator, aileron, or rudder) and sensor bias affecting roll, pitch, or yaw rate gyros that are used in the feedback control loop. The relative configuration of consecutive poses is considered in terms of heading (required turn angle) and relative location of start and end points (position quadrant). Wind and turbulence effects were analyzed for different wind speed and direction and several levels of turbulence severity. The evaluation and comparison of the two path generation algorithms are performed based on generated and actual path length and tracking performance assessed in terms of tracking errors and control activity.;Although continuous position and velocity are ensured, the Dubins path yields discontinuous changes in path curvature and hence in commanded lateral accelerations at the transition points between the circular arcs and straight segments. The simulation results show that this generally leads to increased trajectory tracking errors, longer actual paths, and more intense control surface activity. The gradual (linear) change in clothoid curvature yields a continuous change in commanded lateral accelerations with general positive effects on the overall UAV performance based on the metrics considered. The simulation results show general similar trends for all factors considered. As a result, it may be concluded that, due to the continuous change in commanded lateral acceleration, the clothoid path generation algorithm provides overall better performance than the Dubins algorithm, at both normal and abnormal flight conditions, if the UAV mission involves significant maneuvers requiring intense lateral acceleration commands

Real-Time Monitoring and Fault Diagnostics in Roll-To-Roll Manufacturing Systems

A roll-to-roll (R2R) process is a manufacturing technique involving continuous processing of a flexible substrate as it is transferred between rotating rolls. It integrates many additive and subtractive processing techniques to produce rolls of product in an efficient and cost-effective way due to its high production rate and mass quantity. Therefore, the R2R processes have been increasingly implemented in a wide range of manufacturing industries, including traditional paper/fabric production, plastic and metal foil manufacturing, flexible electronics, thin film batteries, photovoltaics, graphene films production, etc. However, the increasing complexity of R2R processes and high demands on product quality have heightened the needs for effective real-time process monitoring and fault diagnosis in R2R manufacturing systems. This dissertation aims at developing tools to increase system visibility without additional sensors, in order to enhance real-time monitoring, and fault diagnosis capability in R2R manufacturing systems. First, a multistage modeling method is proposed for process monitoring and quality estimation in R2R processes. Product-centric and process-centric variation propagation are introduced to characterize variation propagation throughout the system. The multistage model mainly focuses on the formulation of process-centric variation propagation, which uniquely exists in R2R processes, and the corresponding product quality measurements with both physical knowledge and sensor data analysis. Second, a nonlinear analytical redundancy method is proposed for sensor validation to ensure the accuracy of sensor measurements for process and quality control. Parity relations based on nonlinear observation matrix are formulated to characterize system dynamics and sensor measurements. Robust optimization is designed to identify the coefficient of parity relations that can tolerate a certain level of measurement noise and system disturbances. The effect of the change of operating conditions on the value of the optimal objective function – parity residuals and the optimal design variables – parity coefficients are evaluated with sensitivity analysis. Finally, a multiple model approach for anomaly detection and fault diagnosis is introduced to improve the diagnosability under different operating regimes. The growing structure multiple model system (GSMMS) is employed, which utilizes Voronoi sets to automatically partition the entire operating space into smaller operating regimes. The local model identification problem is revised by formulating it into an optimization problem based on the loss minimization framework and solving with the mini-batch stochastic gradient descent method instead of least squares algorithms. This revision to the GSMMS method expands its capability to handle the local model identification problems that cannot be solved with a closed-form solution. The effectiveness of the models and methods are determined with testbed data from an R2R process. The results show that those proposed models and methods are effective tools to understand variation propagation in R2R processes and improve estimation accuracy of product quality by 70%, identify the health status of sensors promptly to guarantee data accuracy for modeling and decision making, and reduce false alarm rate and increase detection power under different operating conditions. Eventually, those tools developed in this thesis contribute to increase the visibility of R2R manufacturing systems, improve productivity and reduce product rejection rate.PHDMechanical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/146114/1/huanyis_1.pd

Wheelchair lifter

Basically, a wheelchair stair lift is a motorized, meaning by carrying a person seated in a wheelchair up and down stairs. A wheelchair lift, also known as a platform lift, or vertical platform lift is a fully powered device designed to raise a wheelchair and its occupant in order to overcome a step or similar vertical barrier (Figure 8.1). Wheelchair lifts can be installed in homes or businesses and are often added to both private and public vehicles in order to meet accessibility requirements laid out by the Americans with Disabilities Act of 1990 (ADA). These mobility devices are often installed in homes as an alternative to a stair lift, which only transport a passenger and not his/her wheelchair or mobility scooter. It is installed over the stairs in such a way that the stairs can still be used in the usual fashion. There is no need of breaking down or reconstructing the existing building

Fuzzy Controllers

Trying to meet the requirements in the field, present book treats different fuzzy control architectures both in terms of the theoretical design and in terms of comparative validation studies in various applications, numerically simulated or experimentally developed. Through the subject matter and through the inter and multidisciplinary content, this book is addressed mainly to the researchers, doctoral students and students interested in developing new applications of intelligent control, but also to the people who want to become familiar with the control concepts based on fuzzy techniques. Bibliographic resources used to perform the work includes books and articles of present interest in the field, published in prestigious journals and publishing houses, and websites dedicated to various applications of fuzzy control. Its structure and the presented studies include the book in the category of those who make a direct connection between theoretical developments and practical applications, thereby constituting a real support for the specialists in artificial intelligence, modelling and control fields

Model-based control of lateral web behavior - An interconnection of two web guiding systems within packaging machinery

Within packaging industry mostly web materials are used to form bags or similar shaped packages. In order to professionally convert these materials and achieving increasing quality requirements of bags, detailed knowledge of lateral web dynamics is mandatory. One major problem of vertical form fill and seal machines is accuracy of the lateral web positioning process of multi-layer webs. To obtain a high quality bag with minor visibility of inner web layer, positioning accuracy has to be ±0.5 mm. Due to different converting steps within a vertical form fill and seal machine and necessity of positioning for each step, more than one web guiding system is required. This leads to the major problem, which is solved within this paper: the combination of two web guiding systems within a vertical form fill and seal machine.First of all, this paper shows some of the most important milestones within research work of lateral web dynamics presenting the current state of the art. A special approach of hybrid modeling the lateral web behavior is established as well. Thus, a hybrid model of a rotating frame system can be introduced. Direct use of the model within a machine control leads to the hybrid modeling approach. Measurements and simulation results are matching with less than ±0.5 mm difference.After introducing the hybrid modeling approach of a rotating frame system, interconnection strategies of a lateral moveable web roll system and the mentioned rotating frame system are given. To reach the target of combining these systems with the mentioned positioning accuracy and usability of a certain controller directly on a machine control unit, different types of controllers are developed and evaluated. A PID-controller analyzed firstly in this paper shows good results but doesn't achieve the target accuracy. The next investigated controller is a model-based control algorithm. This uses the simulated lateral web behavior, induced by the lateral movable web role, to predict and calculate the needed movement of rotating frame system in order to e.g. compensate the movement. With this method, results in the needed accuracy range are achieved and assured by measurements. However, the issue of exceeding the accuracy level due to differences between simulated and real web behavior still exists.A controller containing a tuned PID-controller and a model-based control algorithm is investigated at the end of this paper via a simulation and achieves the accuracy range of ±0.5 mm despite of high position differences between simulated and real web behavior. Summarized, the paper presents simulation and control methods of lateral web behavior, which can be directly computed and used on a machine control unit with very good results

Robust and Decentralized Control of Web Winding Systems

This research addresses the velocity and tension regulation problems in web handling, including those found in the single element of an accumulator and those in the large-scale system settings. A continuous web winding system is a complex large-scale interconnected dynamics system with numerous tension zones to transport the web while processing it. A major challenge in controlling such systems is the unexpected disturbances that propagate through the system and affect both tension and velocity loops along the way. To solve this problem, a unique active disturbance rejection control (ADRC) strategy is proposed. Simulation results show remarkable disturbance rejection capability of the proposed control scheme in coping with large dynamic variations commonly seen in web winding systems. Another complication in web winding system stems from its large-scale and interconnected dynamics which makes control design difficult. This motivates the research in formulating a novel robust decentralized control strategy. The key idea in the proposed approach is that nonlinearities and interactions between adjunct subsystems are regarded as perturbations, to be estimated by an augmented state observer and rejected in the control loop, therefore making the local control design extremely simple. The proposed decentralized control strategy was implemented on a 3-tension-zone web winding processing line. Simulation results show that the proposed control method leads to much better tension and velocity regulation quality than the existing controller common in industry. Finally, this research tackles the challenging problem of stability analysis. Although ADRC has demonstrated the validity and advantage in many applications, the rigorous stability study has not been fully addressed previously. To this end, stability characterization of ADRC is carried out in this work. The closed-loop system is first reformulated, resulting in a form that allows the application of the well established singular perturbation method. Based on the decom