Design of On-Chip Self-Testing Signature Register

Over the last few years, scan test has turn out to be too expensive to implement for industry standard designs due to increasing test data volume and test time. The test cost of a chip is mainly governed by the resource utilization of Automatic Test Equipment (ATE). Also, it directly depends upon test time that includes time required to load test program, to apply test vectors and to analyze generated test response of the chip. An issue of test time and data volume is increasingly appealing designers to use on-chip test data compactors, either on input side or output side or both. Such techniques significantly address the former issues but have little hold over increasing number of input-outputs under test mode. Further, test pins on DUT are increasing over the generations. Thus, scan channels on test floor are falling short in number for placement of such ICs. To address issues discussed above, we introduce an on-chip self-testing signature register. It comprises a response compactor and a comparator. The compactor compacts large chunk of response data to a small test signature whereas the comparator compares this test signature with desired one. The overall test result for the design is generated on single output pin. Being no storage of test response is demanded, the considerable reduction in ATE memory can be observed. Also, with only single pin to be monitored for test result, the number of tester channels and compare edges on ATE side significantly reduce at the end of the test. This cuts down maintenance and usage cost of test floor and increases its life time. Furthermore reduction in test pins gives scope for DFT engineers to increase number of scan chains so as to further reduce test time

Secure Split Test for Preventing IC Piracy by Un-Trusted Foundry and Assembly

In the era of globalization, integrated circuit design and manufacturing is spread across different continents. This has posed several hardware intrinsic security issues. The issues are related to overproduction of chips without knowledge of designer or OEM, insertion of hardware Trojans at design and fabrication phase, faulty chips getting into markets from test centers, etc. In this thesis work, we have addressed the problem of counterfeit IC‟s getting into the market through test centers. The problem of counterfeit IC has different dimensions. Each problem related to counterfeiting has different solutions. Overbuilding of chips at overseas foundry can be addressed using passive or active metering. The solution to avoid faulty chips getting into open markets from overseas test centers is secure split test (SST). The further improvement to SST is also proposed by other researchers and is known as Connecticut Secure Split Test (CSST). In this work, we focus on improvements to CSST techniques in terms of security, test time and area. In this direction, we have designed all the required sub-blocks required for CSST architecture, namely, RSA, TRNG, Scrambler block, study of benchmark circuits like S38417, adding scan chains to benchmarks is done. Further, as a security measure, we add, XOR gate at the output of the scan chains to obfuscate the signal coming out of the scan chains. Further, we have improved the security of the design by using the PUF circuit instead of TRNG and avoid the use of the memory circuits. This use of PUF not only eliminates the use of memory circuits, but also it provides the way for functional testing also. We have carried out the hamming distance analysis for introduced security measure and results show that security design is reasonably good.Further, as a future work we can focus on: • Developing the circuit which is secuered for the whole semiconductor supply chain with reasonable hamming distance and less area overhead

Towards an embedded board-level tester: study of a configurable test processor

The demand for electronic systems with more features, higher performance, and less power consumption increases continuously. This is a real challenge for design and test engineers because they have to deal with electronic systems with ever-increasing complexity maintaining production and test costs low and meeting critical time to market deadlines. For a test engineer working at the board-level, this means that manufacturing defects must be detected as soon as possible and at a low cost. However, the use of classical test techniques for testing modern printed circuit boards is not sufficient, and in the worst case these techniques cannot be used at all. This is mainly due to modern packaging technologies, a high device density, and high operation frequencies of modern printed circuit boards. This leads to very long test times, low fault coverage, and high test costs. This dissertation addresses these issues and proposes an FPGA-based test approach for printed circuit boards. The concept is based on a configurable test processor that is temporarily implemented in the on-board FPGA and provides the corresponding mechanisms to communicate to external test equipment and co-processors implemented in the FPGA. This embedded test approach provides the flexibility to implement test functions either in the external test equipment or in the FPGA. In this manner, tests are executed at-speed increasing the fault coverage, test times are reduced, and the test system can be adapted automatically to the properties of the FPGA and devices located on the board. An essential part of the FPGA-based test approach deals with the development of a test processor. In this dissertation the required properties of the processor are discussed, and it is shown that the adaptation to the specific test scenario plays a very important role for the optimization. For this purpose, the test processor is equipped with configuration parameters at the instruction set architecture and microarchitecture level. Additionally, an automatic generation process for the test system and for the computation of some of the processor’s configuration parameters is proposed. The automatic generation process uses as input a model known as the device under test model (DUT-M). In order to evaluate the entire FPGA-based test approach and the viability of a processor for testing printed circuit boards, the developed test system is used to test interconnections to two different devices: a static random memory (SRAM) and a liquid crystal display (LCD). Experiments were conducted in order to determine the resource utilization of the processor and FPGA-based test system and to measure test time when different test functions are implemented in the external test equipment or the FPGA. It has been shown that the introduced approach is suitable to test printed circuit boards and that the test processor represents a realistic alternative for testing at board-level.Der Bedarf an elektronischen Systemen mit zusätzlichen Merkmalen, höherer Leistung und geringerem Energieverbrauch nimmt ständig zu. Dies stellt eine erhebliche Herausforderung für Entwicklungs- und Testingenieure dar, weil sie sich mit elektronischen Systemen mit einer steigenden Komplexität zu befassen haben. Außerdem müssen die Herstellungs- und Testkosten gering bleiben und die Produkteinführungsfristen so kurz wie möglich gehalten werden. Daraus folgt, dass ein Testingenieur, der auf Leiterplatten-Ebene arbeitet, die Herstellungsfehler so früh wie möglich entdecken und dabei möglichst niedrige Kosten verursachen soll. Allerdings sind die klassischen Testmethoden nicht in der Lage, die Anforderungen von modernen Leiterplatten zu erfüllen und im schlimmsten Fall können diese Testmethoden überhaupt nicht verwendet werden. Dies liegt vor allem an modernen Gehäuse-Technologien, der hohen Bauteildichte und den hohen Arbeitsfrequenzen von modernen Leiterplatten. Das führt zu sehr langen Testzeiten, geringer Testabdeckung und hohen Testkosten. Die Dissertation greift diese Problematik auf und liefert einen FPGA-basierten Testansatz für Leiterplatten. Das Konzept beruht auf einem konfigurierbaren Testprozessor, welcher im On-Board-FPGA temporär implementiert wird und die entsprechenden Mechanismen für die Kommunikation mit der externen Testeinrichtung und Co-Prozessoren im FPGA bereitstellt. Dadurch ist es möglich Testfunktionen flexibel entweder auf der externen Testeinrichtung oder auf dem FPGA zu implementieren. Auf diese Weise werden Tests at-speed ausgeführt, um die Testabdeckung zu erhöhen. Außerdem wird die Testzeit verkürzt und das Testsystem automatisch an die Eigenschaften des FPGAs und anderer Bauteile auf der Leiterplatte angepasst. Ein wesentlicher Teil des FPGA-basierten Testansatzes umfasst die Entwicklung eines Testprozessors. In dieser Dissertation wird über die benötigten Eigenschaften des Prozessors diskutiert und es wird gezeigt, dass die Anpassung des Prozessors an den spezifischen Testfall von großer Bedeutung für die Optimierung ist. Zu diesem Zweck wird der Prozessor mit Konfigurationsparametern auf der Befehlssatzarchitektur-Ebene und Mikroarchitektur-Ebene ausgerüstet. Außerdem wird ein automatischer Generierungsprozess für die Realisierung des Testsystems und für die Berechnung einer Untergruppe von Konfigurationsparametern des Prozessors vorgestellt. Der automatische Generierungsprozess benutzt als Eingangsinformation ein Modell des Prüflings (device under test model, DUT-M). Das entwickelte Testsystem wurde zum Testen von Leiterplatten für Verbindungen zwischen dem FPGA und zwei Bauteilen verwendet, um den FPGA-basierten Testansatz und die Durchführbarkeit des Testprozessors für das Testen auf Leiterplatte-Ebene zu evaluieren. Die zwei Bauteile sind ein Speicher mit direktem Zugriff (static random-access memory, SRAM) und eine Flüssigkristallanzeige (liquid crystal display, LCD). Die Experimente wurden durchgeführt, um den Ressourcenverbrauch des Prozessors und Testsystems festzustellen und um die Testzeit zu messen. Dies geschah durch die Implementierung von unterschiedlichen Testfunktionen auf der externen Testeinrichtung und dem FPGA. Dadurch konnte gezeigt werden, dass der FPGA-basierte Ansatz für das Testen von Leiterplatten geeignet ist und dass der Testprozessor eine realistische Alternative für das Testen auf Leiterplatten-Ebene ist

IoT Applications Computing

The evolution of emerging and innovative technologies based on Industry 4.0 concepts are transforming society and industry into a fully digitized and networked globe. Sensing, communications, and computing embedded with ambient intelligence are at the heart of the Internet of Things (IoT), the Industrial Internet of Things (IIoT), and Industry 4.0 technologies with expanding applications in manufacturing, transportation, health, building automation, agriculture, and the environment. It is expected that the emerging technology clusters of ambient intelligence computing will not only transform modern industry but also advance societal health and wellness, as well as and make the environment more sustainable. This book uses an interdisciplinary approach to explain the complex issue of scientific and technological innovations largely based on intelligent computing

FORAMINIFERAL DISTRIBUTION AND SEQUENCE STRATIGRAPHY OF OXFORDIAN SUCCESSIONS IN THE WESSEX/ANGLO-PARIS BASIN

The use of micropalaeontology within a sequence stratigraphic context is rapidly emerging as a valuable tool for the recognition of ancient cycles and sequences. This study shows how micropalaeontology can be used to develop insights into sequence stratigraphic interpretations. A micropalaeontology study of two Upper Jurassic, Oxfordian successions from the South . Dorset Coast, U.K. and the Normandy Coast, France provide the basis for this study. A near continuous succession of the Oxfordian from South Dorset and Normandy were obtained, and foraminifera extracted. Examination of the fauna revealed representatives from 23 families, comprising 36 genera and 126 species. All species were identified and the taxonomy of each studied and described. The abundance and distribution patterns of the foraminifera were used to identify sequence stratigraphic horizons (such as Maximum Flooding Surfaces) and the correlation between the two successions was carried out. Detailed research and examination of the >63µm size fraction lead to the discovery of Oxfordian planktic foraminifera from samples in South Dorset. These are the first known occurrences of planktic foraminifera from the Oxfordian of England and are coeval with previously reported occurrences of planktic taxa in the Oxfordian of Normandy and Seine Maritime (France). This study demonstrates how detailed micropalaeontological data can be combined with sequence stratigraphy to reveal a more accurate picture of the controls on basin fill than can be provided by sedimentology alone. It has demonstrated the importance of the preservation upon the fossil assemblages recovered and how this can influence the establishment of biozones

Multiprocessing techniques for unmanned multifunctional satellites Final report,

Simulation of on-board multiprocessor for long lived unmanned space satellite contro