5,964 research outputs found
Channel Sounding for the Masses: Low Complexity GNU 802.11b Channel Impulse Response Estimation
New techniques in cross-layer wireless networks are building demand for
ubiquitous channel sounding, that is, the capability to measure channel impulse
response (CIR) with any standard wireless network and node. Towards that goal,
we present a software-defined IEEE 802.11b receiver and CIR estimation system
with little additional computational complexity compared to 802.11b reception
alone. The system implementation, using the universal software radio peripheral
(USRP) and GNU Radio, is described and compared to previous work. By overcoming
computational limitations and performing direct-sequence spread-spectrum
(DS-SS) matched filtering on the USRP, we enable high-quality yet inexpensive
CIR estimation. We validate the channel sounder and present a drive test
campaign which measures hundreds of channels between WiFi access points and an
in-vehicle receiver in urban and suburban areas
Distributed multi-user MIMO transmission using real-time sigma-delta-over-fiber for next generation fronthaul interface
To achieve the massive device connectivity and high data rate demanded by 5G, wireless transmission with wider signal bandwidths and higher-order multiple-input multiple-output (MIMO) is inevitable. This work demonstrates a possible function split option for the next generation fronthaul interface (NGFI). The proof-of-concept downlink architecture consists of real-time sigma-delta modulated signal over fiber (SDoF) links in combination with distributed multi-user (MU) MIMO transmission. The setup is fully implemented using off-the-shelf and in-house developed components. A single SDoF link achieves an error vector magnitude (EVM) of 3.14% for a 163.84 MHz-bandwidth 256-QAM OFDM signal (958.64 Mbps) with a carrier frequency around 3.5 GHz transmitted over 100 m OM4 multi-mode fiber at 850 nm using a commercial QSFP module. The centralized architecture of the proposed setup introduces no frequency asynchronism among remote radio units. For most cases, the 2 x 2 MU-MIMO transmission has little performance degradation compared to SISO, 0.8 dB EVM degradation for 40.96 MHz-bandwidth signals and 1.4 dB for 163.84 MHz-bandwidth on average, implying that the wireless spectral efficiency almost doubles by exploiting spatial multiplexing. A 1.4 Gbps data rate (720 Mbps per user, 163.84 MHz-bandwidth, 64-QAM) is reached with an average EVM of 6.66%. The performance shows that this approach is feasible for the high-capacity hot-spot scenario
Large-Scale MIMO Detection for 3GPP LTE: Algorithms and FPGA Implementations
Large-scale (or massive) multiple-input multiple-output (MIMO) is expected to
be one of the key technologies in next-generation multi-user cellular systems,
based on the upcoming 3GPP LTE Release 12 standard, for example. In this work,
we propose - to the best of our knowledge - the first VLSI design enabling
high-throughput data detection in single-carrier frequency-division multiple
access (SC-FDMA)-based large-scale MIMO systems. We propose a new approximate
matrix inversion algorithm relying on a Neumann series expansion, which
substantially reduces the complexity of linear data detection. We analyze the
associated error, and we compare its performance and complexity to those of an
exact linear detector. We present corresponding VLSI architectures, which
perform exact and approximate soft-output detection for large-scale MIMO
systems with various antenna/user configurations. Reference implementation
results for a Xilinx Virtex-7 XC7VX980T FPGA show that our designs are able to
achieve more than 600 Mb/s for a 128 antenna, 8 user 3GPP LTE-based large-scale
MIMO system. We finally provide a performance/complexity trade-off comparison
using the presented FPGA designs, which reveals that the detector circuit of
choice is determined by the ratio between BS antennas and users, as well as the
desired error-rate performance.Comment: To appear in the IEEE Journal of Selected Topics in Signal Processin
Millimeter-Wave System for High Data Rate Indoor Communications
This paper presents the realization of a wireless Gigabit Ethernet
communication system operating in the 60 GHz band. The system architecture uses
a single carrier modulation. A differential encoded binary phase shift keying
modulation and a differential demodulation scheme are adopted for the
intermediate frequency blocks. The baseband blocks use Reed- Solomon RS (255,
239) coding and decoding for channel forward error correction (FEC). First
results of bit error rate (BER) measurements at 875 Mbps, without channel
coding, are presented for different antennas.Comment: 5 page
Single Carrier Architecture for High Data Rate Wireless PAN Communications System
A 60 GHz wireless Gigabit Ethernet (G.E.) communication system is developed
at IETR. As the 60 GHz radio link operates only in a single-room configuration,
an additional Radio over Fibre (RoF) link is used to ensure the communications
in all the rooms of a residential environment. The realized system covers 2 GHz
bandwidth. Due to the hardware constraints, a symbol rate at 875 Mbps is
attained using simple single carrier architecture. In the baseband (BB)
processing block, an original byte/frame synchronization process is designed to
provide a smaller value of the preamble missing detection and false alarm
probabilities. Bit error rate (BER) measurements have been realized in a large
gym for line-of-sight (LOS) conditions. A Tx-Rx distance greater than 30 meters
was attained with low BER using high gain antennas and forward error correction
RS (255, 239) coding.Comment: Design, Experimentation, Measurement, Performance; IWCMC '10, Caen :
France (2010
- âŠ