A survey of behavioral-level partitioning systems

Many approaches have been developed to partition a system's behavioral description before a structural implementation is synthesized. We highlight the foundations and motivations for behavioral partitioning. We survey behavioral partitioning approaches, discussing abstraction levels, goals, major steps, and key assumptions in each

From FPGA to ASIC: A RISC-V processor experience

This work document a correct design flow using these tools in the Lagarto RISC- V Processor and the RTL design considerations that must be taken into account, to move from a design for FPGA to design for ASIC

CHASSIS : a combined hardware selection and scheduling technique for performance driven synthesis

This report describes a new technique that combines the Hardware Scheduling and Component Selection phases for High Level Synthesis. Our technique simultaneously selects components from a given library while it schedules the operations into different control steps. The algoríthm improves previous work in scheduling because component costs and performance are considered during the scheduling process, enlarging the design search space and resulting in better optimized desígns

Scheduling and partitioning Vlsi circuit operating at multiple supply voltages

With today\u27s increasingly large and complex digital integrated circuit (IC) and system-on-chip designs, power dissipation has emerged as a primary design consideration. Reduction of power consumption in VLSI designs can be achieved at various levels of the design hierarchy, ranging from processing technology, circuit, logic, architectural and algorithmic (behavioral) levels, up to system level. It has also been long recognized that the most dramatic power saving is achievable at the algorithm and architecture levels, where computations are normally described using data/control flow graph. Thus, in this thesis, a multiple supply voltage IC is synthesized at the behavior level; There are, however, a number of practical problems that must be overcome before use of multiple supply voltage becomes prevalent. In particular, lower power is achieved along with an expensive routing cost. Therefore, unlike the existing methods where only scheduling is considered, our synthesis scheme considers both scheduling and partitioning to reduce power consumption due to the functional units as well as the routing cost; The concerned problem is subsequently referred as the multiple voltage scheduling and partitioning problem (MVSP). The MVSP problem is proved to be NP-complete and three behavioral level synthesis algorithms are proposed to minimize power consumption with resources operating at multiple voltages. One is the polynomial time algorithm. The others are heuristic algorithms, which are tabu search algorithm (TS), and simulated annealing algorithm (SA); In the polynomial time algorithm, synthesis is based on the following three-step process. First, one particular supply voltage (selected from a finite and known number of supply voltage levels) is to be determined for each operation in a data flow graph. Then various operations are scheduled so that the power consumption under given time and/or resource constraints can be minimized. Finally, operations are partitioned into different regions running in different supply voltages to minimize the interconnection costs; In TS and SA algorithms, synthesis schemes are performed to minimize the power consumed by resources and interconnections. In particular, we have configured our solutions with a three-tuple vector to account for both the resource assignment and the partition of operation nodes. Special move operation is designed that allows the scheduling and the partitioning to be performed simultaneously; Experiments with a number of digital signal processing benchmarks show that the proposed algorithms achieve the power reduction at different percentage

Comparison of multi-layer bus interconnection and a network on chip solution

Abstract. This thesis explains the basic subjects that are required to take in consideration when designing a network on chip solutions in the semiconductor world. For example, general topologies such as mesh, torus, octagon and fat tree are explained. In addition, discussion related to network interfaces, switches, arbitration, flow control, routing, error avoidance and error handling are provided. Furthermore, there is discussion related to design flow, a computer aided designing tools and a few comprehensive researches. However, several networks are designed for the minimum latency, although there are also versions which trade performance for decreased bus widths. These designed networks are compared with a corresponding multi-layer bus interconnection and both synthesis and register transfer level simulations are run. For example, results from throughput, latency, logic area and power consumptions are gathered and compared. It was discovered that overall throughput was well balanced with the network on chip solutions, although its maximum throughput was limited by protocol conversions. For example, the multi-layer bus interconnection was capable of providing a few times smaller latencies and higher throughputs when only a single interface was injected at the time. However, with parallel traffic and high-performance requirements a network on chip solution provided better results, even though the difference decreased when performance requirements were lower. Furthermore, it was discovered that the network on chip solutions required approximately 3–4 times higher total cell area than the multi-layer bus interconnection and that resources were mainly located at network interfaces and switches. In addition, power consumption was approximately 2–3 times higher and was mostly caused by dynamic consumption.Monitasoisen väyläarkkitehtuurin ja tietokoneverkkomaisen ratkaisun vertailua. Tiivistelmä. Tutkielmassa käsitellään tärkeimpiä aihealueita, jotka tulee huomioida suunniteltaessa tietokoneverkkomaisia väyläratkaisuja puolijohdemaailmassa. Esimerkiksi yleiset rakenteet, kuten verkko-, torus-, kahdeksankulmio- ja puutopologiat käsitellään lyhyesti. Lisäksi alustetaan verkon liitäntäkohdat, kytkimet, vuorottelu, vuon hallinta, reititys, virheiden välttely ja -käsittely. Lopuksi kerrotaan suunnitteluvuon oleellisimmat välivaiheet ja niihin soveltuvia kaupallisia työkaluja, sekä käsitellään lyhyesti muutaman aiemman julkaisun tuloksia. Tutkielmassa käytetään suunnittelutyökalua muutaman tietokoneverkkomaisen ratkaisun toteutukseen ja tavoitteena on saavuttaa pienin mahdollinen latenssi. Toisaalta myös hieman suuremman latenssin versioita suunnitellaan, mutta pienemmillä väylänleveyksillä. Lisäksi suunniteltuja tietokoneverkkomaisia ratkaisuja vertaillaan perinteisempään monitasoiseen väyläarkkitehtuuriin. Esimerkiksi synteesi- ja simulaatiotuloksia, kuten logiikan vaatimaa pinta-alaa, tehonkulutusta, latenssia ja suorituskykyä, vertaillaan keskenään. Tutkielmassa selvisi, että suunnittelutyökalulla toteutetut tietokoneverkkomaiset ratkaisut mahdollistivat tasaisemman suorituskyvyn, joskin niiden suurin saavutettu suorituskyky ja pienin latenssi määräytyivät protokollan käännöksen aiheuttamasta viiveestä. Tutkielmassa havaittiin, että perinteisemmillä menetelmillä saavutettiin noin kaksi kertaa suurempi suorituskyky ja pienempi latenssi, kun verkossa ei ollut muuta liikennettä. Rinnakkaisen liikenteen lisääntyessä tietokoneverkkomainen ratkaisu tarjosi keskimäärin paremman suorituskyvyn, kun sille asetetut tehokkuusvaateet olivat suuret, mutta suorituskykyvaatimuksien laskiessa erot kapenivat. Lisäksi huomattiin, että tietokoneverkkomaisten ratkaisujen käyttämä pinta-ala oli noin 3–4 kertaa suurempi kuin monitasoisella väyläarkkitehtuurilla ja että resurssit sijaitsivat enimmäkseen verkon liittymäkohdissa ja kytkimissä. Lisäksi tehonkulutuksen huomattiin olevan noin 2–3 kertaa suurempi, joskin sen havaittiin koostuvan pääosin dynaamisesta kulutuksesta

Compiling dataflow graphs into hardware

Department Head: L. Darrell Whitley.2005 Fall.Includes bibliographical references (pages 121-126).Conventional computers are programmed by supplying a sequence of instructions that perform the desired task. A reconfigurable processor is "programmed" by specifying the interconnections between hardware components, thereby creating a "hardwired" system to do the particular task. For some applications such as image processing, reconfigurable processors can produce dramatic execution speedups. However, programming a reconfigurable processor is essentially a hardware design discipline, making programming difficult for application programmers who are only familiar with software design techniques. To bridge this gap, a programming language, called SA-C (Single Assignment C, pronounced "sassy"), has been designed for programming reconfigurable processors. The process involves two main steps - first, the SA-C compiler analyzes the input source code and produces a hardware-independent intermediate representation of the program, called a dataflow graph (DFG). Secondly, this DFG is combined with hardware-specific information to create the final configuration. This dissertation describes the design and implementation of a system that performs the DFG to hardware translation. The DFG is broken up into three sections: the data generators, the inner loop body, and the data collectors. The second of these, the inner loop body, is used to create a computational structure that is unique for each program. The other two sections are implemented by using prebuilt modules, parameterized for the particular problem. Finally, a "glue module" is created to connect the various pieces into a complete interconnection specification. The dissertation also explores optimizations that can be applied while processing the DFG, to improve performance. A technique for pipelining the inner loop body is described that uses an estimation tool for the propagation delay of the nodes within the dataflow graph. A scheme is also described that identifies subgraphs with the dataflow graph that can be replaced with lookup tables. The lookup tables provide a faster implementation than random logic in some instances

Gate-level timing analysis and waveform evaluation

Static timing analysis (STA) is an integral part of modern VLSI chip design. Table lookup based methods are widely used in current industry due to its fast runtime and mature algorithms. Conventional STA algorithms based on table-lookup methods are developed under many assumptions in timing analysis; however, most of those assumptions, such as that input signals and output signals can be accurately modeled as ramp waveforms, are no longer satisfactory to meet the increasing demand of accuracy for new technologies. In this dissertation, we discuss several crucial issues that conventional STA has not taken into consideration, and propose new methods to handle these issues and show that new methods produce accurate results. In logic circuits, gates may have multiple inputs and signals can arrive at these inputs at different times and with different waveforms. Different arrival times and waveforms of signals can cause very different responses. However, multiple-input transition effects are totally overlooked by current STA tools. Using a conventional single-input transition model when multiple-input transition happens can cause significant estimation errors in timing analysis. Previous works on this issue focus on developing a complicated gate model to simulate the behavior of logic gates. These methods have high computational cost and have to make significant changes to the prevailing STA tools, and are thus not feasible in practice. This dissertation proposes a simplified gate model, uses transistor connection structures to capture the behavior of multiple-input transitions and requires no change to the current STA tools. Another issue with table lookup based methods is that the load of each gate in technology libraries is modeled as a single lumped capacitor. But in the real circuit, the Abstract 2 gate connects to its subsequent gates via metal wires. As the feature size of integrated circuit scales down, the interconnection cannot be seen as a simple capacitor since the resistive shielding effect will largely affect the equivalent capacitance seen from the gate. As the interconnection has numerous structures, tabulating the timing data for various interconnection structures is not feasible. In this dissertation, by using the concept of equivalent admittance, we reduce an arbitrary interconnection structure into an equivalent π-model RC circuit. Many previous works have mapped the π-model to an effective capacitor, which makes the table lookup based methods useful again. However, a capacitor cannot be equivalent to a π-model circuit, and will thus result in significant inaccuracy in waveform evaluation. In order to obtain an accurate waveform at gate output, a piecewise waveform evaluation method is proposed in this dissertation. Each part of the piecewise waveform is evaluated according to the gate characteristic and load structures. Another contribution of this dissertation research is a proposed equivalent waveform search method. The signal waveforms can be very complicated in the real circuits because of noises, race hazards, etc. The conventional STA only uses one attribute (i.e., transition time) to describe the waveform shape which can cause significant estimation errors. Our approach is to develop heuristic search functions to find equivalent ramps to approximate input waveforms. Here the transition time of a final ramp can be completely different from that of the original waveform, but we can get higher accuracy on output arrival time and transition time. All of the methods mentioned in this dissertation require no changes to the prevailing STA tools, and have been verified across different process technologies