Efficient path protection using Bi-directional WDM transmission technology

Bi-directional WDM transmission is a technique that allows wavelengths to be transmitted simultaneously in both directions in a single fiber. Compared with unidirectional WDM systems, it not only saves the cost of deploying extra fibers, but also allows more flexible bandwidth provisioning. To exploit the advantages brought by this flexibility, we investigate path protection based on bi-directional WDM transmission system in this paper. With path protection, a call is accepted if and only if an active data path together with a disjointed backup path can be found in the network. With bi-directional WDM, backup resources sharing in both directions of a fiber is possible. To encourage resources sharing, new cost functions are judiciously designed. Based on them, two original path protection schemes are proposed in this paper, BiPro and BiProLP, where BiProLP aims at further economizing the hardware cost incurred by BiPro. In contrast to the traditional unidirectional schemes, we show that both BiPro and BiProLP can yield noticeably lower call blocking probability, higher system capacity and snorter active/backup path length. © 2005 IEEE.published_or_final_versio

Logical topology design for IP rerouting: ASONs versus static OTNs

IP-based backbone networks are gradually moving to a network model consisting of high-speed routers that are flexibly interconnected by a mesh of light paths set up by an optical transport network that consists of wavelength division multiplexing (WDM) links and optical cross-connects. In such a model, the generalized MPLS protocol suite could provide the IP centric control plane component that will be used to deliver rapid and dynamic circuit provisioning of end-to-end optical light paths between the routers. This is called an automatic switched optical (transport) network (ASON). An ASON enables reconfiguration of the logical IP topology by setting up and tearing down light paths. This allows to up- or downgrade link capacities during a router failure to the capacities needed by the new routing of the affected traffic. Such survivability against (single) IP router failures is cost-effective, as capacity to the IP layer can be provided flexibly when necessary. We present and investigate a logical topology optimization problem that minimizes the total amount or cost of the needed resources (interfaces, wavelengths, WDM line-systems, amplifiers, etc.) in both the IP and the optical layer. A novel optimization aspect in this problem is the possibility, as a result of the ASON, to reuse the physical resources (like interface cards and WDM line-systems) over the different network states (the failure-free and all the router failure scenarios). We devised a simple optimization strategy to investigate the cost of the ASON approach and compare it with other schemes that survive single router failures

Spare capacity modelling and its applications in survivable iP-over-optical networks

As the interest in IP-over-optical networks are becoming the preferred core network architecture, survivability has emerged as a major concern for network service providers; a result of the potentially huge traffic volumes that will be supported by optical infrastructure. Therefore, implementing recovery strategies is critical. In addition to the traditional recovery schemes based around protection and restoration mechanisms, pre-allocated restoration represents a potential candidate to effect and maintain network resilience under failure conditions. Preallocated restoration technique is particularly interesting because it provides a trade-off in terms of recovery performance and resources between protection and restoration schemes. In this paper, the pre-allocated restoration performance is investigated under single and dual-link failures considering a distributed GMPLSbased IP/WDM mesh network. Two load-based spare capacity optimisation methods are proposed in this paper; Local Spare Capacity Optimisation (LSCO) and Global Spare Capacity Optimisation (GSCO)

Optimized Design of Survivable MPLS over Optical Transport Networks. Optical Switching and Networking

In this paper we study different options for the survivability implementation in MPLS over Optical Transport Networks in terms of network resource usage and configuration cost. We investigate two approaches to the survivability deployment: single layer and multilayer survivability and present various methods for spare capacity allocation (SCA) to reroute disrupted traffic. The comparative analysis shows the influence of the traffic granularity on the survivability cost: for high bandwidth LSPs, close to the optical channel capacity, the multilayer survivability outperforms the single layer one, whereas for low bandwidth LSPs the single layer survivability is more cost-efficient. For the multilayer survivability we demonstrate that by mapping efficiently the spare capacity of the MPLS layer onto the resources of the optical layer one can achieve up to 22% savings in the total configuration cost and up to 37% in the optical layer cost. Further savings (up to 9 %) in the wavelength use can be obtained with the integrated approach to network configuration over the sequential one, however, at the increase in the optimization problem complexity. These results are based on a cost model with actual technology pricing and were obtained for networks targeted to a nationwide coverage

Scatter search based met heuristic for robust optimization of the deploying of "DWDM" technology on optical networks with survivability

In this paper we discuss the application of a met heuristic approach based on the Scatter Search to deal with robust optimization of the planning problem in the deploying of the Dense Wavelength Division Multiplexing (DWDM) technology on an existing optical fiber network taking into account, in addition to the forecasted demands, the uncertainty in the survivability requirements

Fiber amplifiers, directly modulated transmitters and a ring network structure for optical communications

The three technologies that are considered the key elements in building a metropolitan area optical network are studied in this thesis. They are optical amplification, high-speed low cost transmitters and ring network structures. These studies concentrate on cost reduction of these three technologies thus enabling the use of optical networks in small customer base metropolitan areas. The research on optical amplification concentrated first on the solution doping process, at present the most used method for producing erbium doped fiber. It was found that separationing the soot growth and the sintering improved the uniformity of the porous layer. This made the homogeneity of the doping concentration in the fiber core better. The effects of index profile variations that arise from the non-ideal solution doping process were also simulated. In the search for a better doping method a new nanoparticle glass-forming process, the direct nanoparticle deposition, was developed. In this process the doping is done simultaneously with glass formation. Utilizing this new process it was possible to improve the uniformity of the doping resulting in higher usable doping levels and shorter erbium doped fiber lengths in the amplifiers. There were fewer limitations in the amplifier caused by optical non-linearities and polarization mode dispersion since shorter fiber lengths were needed. The double cladding fiber, which avoids the costly coupling of the pump laser into a single mode waveguide, was also studied. This pumping scheme was found to improve the inversion uniformity in the erbium doped fiber core thereby enhancing the power conversion efficiency for the long wavelength band amplifier. In characterizing the erbium doped fiber amplifier the gain and noise figure was measured with a temporal filter setup. It was made of simple, low cost components but yielded accurate measurements since the noise originating from the amplified spontaneous emission was measured at the signal wavelength. In the study of fiber amplifier controlling schemes the input power of the fiber amplifier was successfully used to regulate the pump laser. This feed-forward control scheme provides a simple, low cost control and managment system for the erbium doped fiber amplifier in metropolitan area network applications that require flexible adding and dropping of wavelength channels. The transmitter research focused on the DFB laser due to its simplicity and low cost structure. A solid state Fabry-Perot etalon made from double polished silicon chip was used as a frequency discriminator in the chirp analyser developed for the DFB lasers. This wavelength discriminator did not require repeated calibration or active stabilisation and was controled electrically enabling automatic measurements. The silicon Fabry-Perot etalon was also used for simultaneous spectral filtering and wavelength control of the laser. The usable dispersion limited transmission length was increased when the filter was used in conjunction with the directly modulated distributed feedback laser transmitter. The combination of spatial multiplexing and dense wavelength division multiplexing in ring topology was investigated in the course of the research on the ring network as the feeder part of the metropolitan network. A new way to organize different wavelengths and fibers was developed. This ring network structure was simulated and an experimental ring network built. The results of the studies demonstrated that the same limitations effecting uni-directional ring structures also are the main limitations on the scalability of the spatial and wavelength division multiplexed ring networks based on bi-directional transmission when the node spacing is short. The developed ring network structure demonstrated major cost reductions when compared with the heavy use of wavelength division multiplexing. The node structure was also greatly simplified resulting in less need for different wavelength transmitters in each node. Furthermore the node generated only minor losses for the passing signals thus reducing the need for optical amplification.reviewe