Efficient FPGA implementation of high-throughput mixed radix multipath delay commutator FFT processor for MIMO-OFDM

This article presents and evaluates pipelined architecture designs for an improved high-frequency Fast Fourier Transform (FFT) processor implemented on Field Programmable Gate Arrays (FPGA) for Multiple Input Multiple Output Orthogonal Frequency Division Multiplexing (MIMO-OFDM). The architecture presented is a Mixed-Radix Multipath Delay Commutator. The presented parallel architecture utilizes fewer hardware resources compared to Radix-2 architecture, while maintaining simple control and butterfly structures inherent to Radix-2 implementations. The high-frequency design presented allows enhancing system throughput without requiring additional parallel data paths common in other current approaches, the presented design can process two and four independent data streams in parallel and is suitable for scaling to any power of two FFT size N. FPGA implementation of the architecture demonstrated significant resource efficiency and high-throughput in comparison to relevant current approaches within literature. The proposed architecture designs were realized with Xilinx System Generator (XSG) and evaluated on both Virtex-5 and Virtex-7 FPGA devices. Post place and route results demonstrated maximum frequency values over 400 MHz and 470 MHz for Virtex-5 and Virtex-7 FPGA devices respectively

FPGA implementation of a 10 GS/s variable-length FFT for OFDM-based optical communication systems

[EN] The transmission rate in current passive optical networks can be increased by employing Orthogonal Frequency Division Multiplexing (OFDM) modulation. The computational kernel of this modulation is the fast Fourier transform (FFT) operator, which has to achieve a very high throughput in order to be used in optical networks. This paper presents the implementation in an FPGA device of a variable-length FFT that can be configured in run-time to compute different FFT lengths between 16 and 1024 points. The FFT reaches a throughput of 10 GS/s in a Virtex-7 485T-3 FPGA device and was used to implement a 20 Gb/s optical OFDM receiver. (C) 2018 Elsevier B.V. All rights reserved.This work was supported by the Spanish Ministerio de Economia y Competitividad under project TEC2015-70858-C2-2-R with FEDER funds.Bruno, JS.; Almenar Terre, V.; Valls Coquillat, J. (2019). FPGA implementation of a 10 GS/s variable-length FFT for OFDM-based optical communication systems. Microprocessors and Microsystems. 64:195-204. https://doi.org/10.1016/j.micpro.2018.12.002S1952046

Improving Energy Efficiency of OFDM Using Adaptive Precision Reconfigurable FFT

International audienceBeing an essential issue in digital systems, especially battery-powered devices, energy efficiency has been the subject of intensive research. In this research, a multi-precision FFT module with dynamic run-time reconfigurability is proposed to trade off accuracy with the energy efficiency of OFDM in an SDR-based architecture. To support variable-size FFT, a reconfigurable memory-based architecture is investigated. It is revealed that the radix-4 FFT has the minimum computational complexity in this architecture. Regarding implementation constraints such as fixed-width memory, a noise model is exploited to statistically analyze the proposed architecture. The required FFT word-lengths for different criteria—namely BER, modulation scheme, FFT size, and SNR—are computed analytically and confirmed by simulations in AWGN and Rayleigh fading channels. At run-time, the most energy-efficient word-length is chosen and the FFT is reconfigured until the required application-specific BER is met. Evaluations show that the implementation area and the number of memory accesses are reduced. The results obtained from synthesizing basic operators of the proposed design on an FPGA show energy consumption experienced a saving of over 80 %

Software-Defined Radio FPGA Cores: Building towards a Domain-Specific Language

This paper reports on the design and implementation of an open-source library of parameterizable and reusable Hardware Description Language (HDL) Intellectual Property (IP) cores designed for the development of Software-Defined Radio (SDR) applications that are deployed on FPGA-based reconfigurable computing platforms. The library comprises a set of cores that were chosen, together with their parameters and interfacing schemas, based on recommendations from industry and academic SDR experts. The operation of the SDR cores is first validated and then benchmarked against two other cores libraries of a similar type to show that our cores do not take much more logic elements than existing cores and that they support a comparable maximum clock speed. Finally, we propose our design for a Domain-Specific Language (DSL) and supporting tool-flow, which we are in the process of building using our SDR library and the Delite DSL framework. We intend to take this DSL and supporting framework further to provide a rapid prototyping system for SDR application development to programmers not experienced in HDL coding. We conclude with a summary of the main characteristics of our SDR library and reflect on how our DSL tool-flow could assist other developers working in SDR field

Low power FFT processor design considerations for OFDM communications

Today\u27s emerging communication technologies require fast processing as well as efficient use of resources. This project specifically addresses the power-efficient design of an FFT processor as it relates to OFDM communications such as cognitive radio. The Fast Fourier Transform (FFT) processor is what enables the efficient modulation in OFDM. As the FFT processor is the most computationally intensive component in OFDM communication, the power efficiency improvement of this component can have great impacts on the overall system. These impacts are significant considering the number of mobile and remote communication devices that rely on limited battery-powered operation. This project explores current FFT processor algorithms and architectures as well as optimization techniques that aim to reduce the power consumption of these devices. A floating point as well as a fixed point dynamically size-configurable FFT processor was designed in VHDL for FPGA applications, and power-saving modifications were implemented while analyzing the results

SdrLift: A Domain-Specific Intermediate Hardware Synthesis Framework for Prototyping Software-Defined Radios

Modern design of Software-Defined Radio (SDR) applications is based on Field Programmable Gate Arrays (FPGA) due to their ability to be configured into solution architectures that are well suited to domain-specific problems while achieving the best trade-off between performance, power, area, and flexibility. FPGAs are well known for rich computational resources, which traditionally include logic, register, and routing resources. The increased technological advances have seen FPGAs incorporating more complex components that comprise sophisticated memory blocks, Digital Signal Processing (DSP) blocks, and high-speed interfacing to Gigabit Ethernet (GbE) and Peripheral Component Interconnect Express (PCIe) bus. Gateware for programming FPGAs is described at a lowlevel of design abstraction using Register Transfer Language (RTL), typically using either VHSIC-HDL (VHDL) or Verilog code. In practice, the low-level description languages have a very steep learning curve, provide low productivity for hardware designers and lack readily available open-source library support for fundamental designs, and consequently limit the design to only hardware experts. These limitations have led to the adoption of High-Level Synthesis (HLS) tools that raise design abstraction using syntax, semantics, and software development notations that are well-known to most software developers. However, while HLS has made programming of FPGAs more accessible and can increase the productivity of design, they are still not widely adopted in the design community due to the low-level skills that are still required to produce efficient designs. Additionally, the resultant RTL code from HLS tools is often difficult to decipher, modify and optimize due to the functionality and micro-architecture that are coupled together in a single High-Level Language (HLL). In order to alleviate these problems, Domain-Specific Languages (DSL) have been introduced to capture algorithms at a high level of abstraction with more expressive power and providing domain-specific optimizations that factor in new transformations and the trade-off between resource utilization and system performance. The problem of existing DSLs is that they are designed around imperative languages with an instruction sequence that does not match the hardware structure and intrinsics, leading to hardware designs with system properties that are unconformable to the high-level specifications and constraints. The aim of this thesis is, therefore, to design and implement an intermediatelevel framework namely SdrLift for use in high-level rapid prototyping of SDR applications that are based on an FPGA. The SdrLift input is a HLL developed using functional language constructs and design patterns that specify the structural behavior of the application design. The functionality of the SdrLift language is two-fold, first, it can be used directly by a designer to develop the SDR applications, secondly, it can be used as the Intermediate Representation (IR) step that is generated by a higher-level language or a DSL. The SdrLift compiler uses the dataflow graph as an IR to structurally represent the accelerator micro-architecture in which the components correspond to the fine-level and coarse-level Hardware blocks (HW Block) which are either auto-synthesized or integrated from existing reusable Intellectual Property (IP) core libraries. Another IR is in the form of a dataflow model and it is used for composition and global interconnection of the HW Blocks while making efficient interfacing decisions in an attempt to satisfy speed and resource usage objectives. Moreover, the dataflow model provides rules and properties that will be used to provide a theoretical framework that formally analyzes the characteristics of SDR applications (i.e. the throughput, sample rate, latency, and buffer size among other factors). Using both the directed graph flow (DFG) and the dataflow model in the SdrLift compiler provides two benefits: an abstraction of the microarchitecture from the high-level algorithm specifications and also decoupling of the microarchitecture from the low-level RTL implementation. Following the IR creation and model analyses is the VHDL code generation which employs the low-level optimizations that ensure optimal hardware design results. The code generation process per forms analysis to ensure the resultant hardware system conforms to the high-level design specifications and constraints. SdrLift is evaluated by developing representative SDR case studies, in which the VHDL code for eight different SDR applications is generated. The experimental results show that SdrLift achieves the desired performance and flexibility, while also conserving the hardware resources utilized