26 research outputs found
A Generalized Framework on Beamformer Design and CSI Acquisition for Single-Carrier Massive MIMO Systems in Millimeter Wave Channels
In this paper, we establish a general framework on the reduced dimensional
channel state information (CSI) estimation and pre-beamformer design for
frequency-selective massive multiple-input multiple-output MIMO systems
employing single-carrier (SC) modulation in time division duplex (TDD) mode by
exploiting the joint angle-delay domain channel sparsity in millimeter (mm)
wave frequencies. First, based on a generic subspace projection taking the
joint angle-delay power profile and user-grouping into account, the reduced
rank minimum mean square error (RR-MMSE) instantaneous CSI estimator is derived
for spatially correlated wideband MIMO channels. Second, the statistical
pre-beamformer design is considered for frequency-selective SC massive MIMO
channels. We examine the dimension reduction problem and subspace (beamspace)
construction on which the RR-MMSE estimation can be realized as accurately as
possible. Finally, a spatio-temporal domain correlator type reduced rank
channel estimator, as an approximation of the RR-MMSE estimate, is obtained by
carrying out least square (LS) estimation in a proper reduced dimensional
beamspace. It is observed that the proposed techniques show remarkable
robustness to the pilot interference (or contamination) with a significant
reduction in pilot overhead
Massive MIMO for Internet of Things (IoT) Connectivity
Massive MIMO is considered to be one of the key technologies in the emerging
5G systems, but also a concept applicable to other wireless systems. Exploiting
the large number of degrees of freedom (DoFs) of massive MIMO essential for
achieving high spectral efficiency, high data rates and extreme spatial
multiplexing of densely distributed users. On the one hand, the benefits of
applying massive MIMO for broadband communication are well known and there has
been a large body of research on designing communication schemes to support
high rates. On the other hand, using massive MIMO for Internet-of-Things (IoT)
is still a developing topic, as IoT connectivity has requirements and
constraints that are significantly different from the broadband connections. In
this paper we investigate the applicability of massive MIMO to IoT
connectivity. Specifically, we treat the two generic types of IoT connections
envisioned in 5G: massive machine-type communication (mMTC) and ultra-reliable
low-latency communication (URLLC). This paper fills this important gap by
identifying the opportunities and challenges in exploiting massive MIMO for IoT
connectivity. We provide insights into the trade-offs that emerge when massive
MIMO is applied to mMTC or URLLC and present a number of suitable communication
schemes. The discussion continues to the questions of network slicing of the
wireless resources and the use of massive MIMO to simultaneously support IoT
connections with very heterogeneous requirements. The main conclusion is that
massive MIMO can bring benefits to the scenarios with IoT connectivity, but it
requires tight integration of the physical-layer techniques with the protocol
design.Comment: Submitted for publicatio
Channel correlation-based approach for feedback overhead reduction in massive MIMO
For frequency-division duplex multiple-input-multiple-output (MIMO) systems, the channel state information at the transmitter is usually obtained by sending pilots or reference signals from all elements of the antenna array. The channel is then estimated by the receiver and communicated back to the transmitter. However, for massive MIMO, this periodical estimation of the full transfer matrix can lead to prohibitive overhead. To reduce the amount of data, we propose to estimate the updated channel matrix from the knowledge of the full correlation matrix at the transmitter made during some initialization time and the instantaneous measured channel matrix of smaller size, characterizing the link between the user and a limited number of reference array elements. The proposed algorithm is validated with measured massive MIMO channel transfer functions at 3.5GHz between a uniform rectangular array and different user positions. Since measurements were made in static conditions, the criteria chosen for evaluating the performance of the algorithm are based on a comparison of the predicted channel capacity calculated from either the measured or estimated channel matrix
Design of Joint Spatial and Power Domain Multiplexing Scheme for Massive MIMO Systems
Massive Multiple-Input Multiple-Output (MIMO) is one of the key techniques in 5th generation wireless systems (5G) due to its potential ability to improve spectral efficiency. Most of the existing works on massive MIMO only consider Time Division Duplex (TDD) operation that relies on channel reciprocity between uplink and downlink channels. For Frequency Division Duplex (FDD) systems, with continued efforts, some downlink multiuser MIMO scheme was recently proposed in order to enable “massive MIMO” gains and simplified system operations with limited number of radio frequency (RF) chains in FDD system. However these schemes, such as Joint Spatial Division and Multiplexing (JSDM) scheme and hybrid precoding scheme, only focus on multiuser transmission in spatial domain. Different from most of the existing works, this paper proposes Joint Spatial and Power Multiplexing (JSPM) scheme in FDD systems. It extends existing FDD schemes from spatial division and multiplexing to joint spatial and power domain to achieve more multiplexing gain. The user grouping and scheduling scheme of JSPM is studied and the asymptotic expression for the sum capacity is derived as well. Finally, simulations are conducted to illustrate the effectiveness of the proposed scheme