An Efficiency-Focused Design of Direct-DC Loads in Buildings

Despite the recent interest in direct current (DC) power distribution in buildings, the market for DC-ready loads remains small. The existing DC loads in various products or research test beds are not always designed to efficiently leverage the benefits of DC. This work addresses a pressing need for a study into the development of efficient DC loads. In particular, it focuses on documenting and demonstrating how to best leverage a DC input to eliminate or improve conversion stages in a load’s power converter. This work identifies how typical building loads can benefit from DC input, including bath fans, refrigerators, task lights, and zone lighting. It then details the development of several prototypes that demonstrate efficiency savings with DC. The most efficient direct-DC loads are explicitly designed for DC from the ground up, rather than from an AC modification

Efficiency and Reliability Analysis of AC and 380V DC Data Centers

The rapid growth of the Internet has resulted in colossal increase in the number of data centers. A data center consume a tremendous amount of electricity resulting in high operation cost. Even a slight improvement in the power distribution system of a data center could save millions of dollars in electricity bills. Benchmarks for both AC and 380V DC data centers are developed and efficiency analyses thereof have been performed for an entire year. The efficiency of the power distribution system can be increased if number of power conversion stages can be reduced and more efficient converters are used. Use of wide band gap (WBG) converters will further improve the overall system efficiency because of its high efficiency. The results shows that 380V DC data centers are more efficient than AC data centers with and without PV integration. Using 380V DC distribution system not only improve the efficiency of the system, but it saves millions of dollars by decreasing system downtime. Maintaining high availability at all times is very critical to data centers. The distribution system with higher number of series components is more likely to fail, resulting in increased downtime. This study aims at comparing reliabilities of AC against 380V DC architecture. Reliability assessment was done for both AC and DC systems complying with Tier IV standard. The analysis was done for different level of redundancy (eg. N, N+1, N+2) in the UPS system for both AC and DC systems. Monte Carlo simulation method was used to perform the reliability calculations. The simulation results showed that the 380V DC distribution system has higher level of reliability than AC distribution system in data centers but only up to certain level of redundancy in the UPS system. The reliability level of AC system will approach to that of a DC system when a very high level of redundancy in the UPS system is considered, but this will increase the overall cost of a data center

System configuration, fault detection, location, isolation and restoration: a review on LVDC Microgrid protections

Low voltage direct current (LVDC) distribution has gained the significant interest of research due to the advancements in power conversion technologies. However, the use of converters has given rise to several technical issues regarding their protections and controls of such devices under faulty conditions. Post-fault behaviour of converter-fed LVDC system involves both active converter control and passive circuit transient of similar time scale, which makes the protection for LVDC distribution significantly different and more challenging than low voltage AC. These protection and operational issues have handicapped the practical applications of DC distribution. This paper presents state-of-the-art protection schemes developed for DC Microgrids. With a close look at practical limitations such as the dependency on modelling accuracy, requirement on communications and so forth, a comprehensive evaluation is carried out on those system approaches in terms of system configurations， fault detection, location, isolation and restoration

Grid Integration of DC Buildings: Standards, Requirements and Power Converter Topologies

Residential dc microgrids and nanogrids are the emerging technology that is aimed to promote the transition to energy-efficient buildings and provide simple, highly flexible integration of renewables, storages, and loads. At the same time, the mass acceptance of dc buildings is slowed down by the relative immaturity of the dc technology, lack of standardization and general awareness about its potential. Additional efforts from multiple directions are necessary to promote this technology and increase its market attractiveness. In the near-term, it is highly likely that the dc buildings will be connected to the conventional ac distribution grid by a front-end ac-dc converter that provides all the necessary protection and desired functionality. At the same time, the corresponding requirements for this converter have not been yet consolidated. To address this, present paper focuses on various aspects of the integration of dc buildings and includes analysis of related standards, directives, operational and compatibility requirements as well as classification of voltage levels. In addition, power converter configurations and modulation methods are analyzed and compared. A classification of topologies that can provide the required functionality for the application is proposed. Finally, future trends and remaining challenges pointed out to motivate new contributions to this topic

Multi-kw dc power distribution system study program

The first phase of the Multi-kw dc Power Distribution Technology Program is reported and involves the test and evaluation of a technology breadboard in a specifically designed test facility according to design concepts developed in a previous study on space vehicle electrical power processing, distribution, and control. The static and dynamic performance, fault isolation, reliability, electromagnetic interference characterisitics, and operability factors of high distribution systems were studied in order to gain a technology base for the use of high voltage dc systems in future aerospace vehicles. Detailed technical descriptions are presented and include data for the following: (1) dynamic interactions due to operation of solid state and electromechanical switchgear; (2) multiplexed and computer controlled supervision and checkout methods; (3) pulse width modulator design; and (4) cable design factors

Extended performance solar electric propulsion thrust system study. Volume 1: Executive summary

Several thrust system design concepts were evaluated and compared using the specifications of the most advanced 30 cm engineering model thruster as the technology base. The extensions in thruster performance required for the Halley's comet mission were defined and alternative thrust system concepts were designed. Confirmation testing and analysis of thruster and power-processing components were performed, and the feasibility of satisfying extended performance requirements was verified. A baseline design was selected from the alternatives considered, and the design analysis and documentation were refined. A program development plan was formulated that outlines the work structure considered necessary for developing, qualifying, and fabricating the flight hardware for the baseline thrust system within the time frame of a project to rendezvous with Halley's comet. An assessment was made of the costs and risks associated with a baseline thrust system as provided to the mission project under this plan. Critical procurements and interfaces were identified and defined. Results are presented