A power efficient 2Gb/s transceiver in 90nm CMOS for 10mm On-Chip interconnect

Global on-chip data communication is becoming a concern as the gap between transistor speed and interconnect bandwidth increases with CMOS process scaling. In this paper a low-swing transceiver for 10mm long 0.54μm wide on-chip interconnect is presented, which achieves a similar data rate as previous designs (a few Gb/s), but at much lower power than recently published work. Both low static power and low dynamic power (low energy per bit) is aimed for. A capacitive pre-emphasis transmitter lowers the voltage swing and increases the bandwidth using a simple inverter based transceiver and capacitive coupling to the interconnect. The receiver uses Decision Feedback Equalization with a power-efficient continuous-time feedback filter. A low power latch-type voltage sense amplifier is used. The transceiver, fabricated in a 1.2V 90nm CMOS process, achieves 2Gb/s. It consumes only 0.28pJ/b, which is 7 times lower than earlier work

Low-Power, High-Speed Transceivers for Network-on-Chip Communication

Networks on chips (NoCs) are becoming popular as they provide a solution for the interconnection problems on large integrated circuits (ICs). But even in a NoC, link-power can become unacceptably high and data rates are limited when conventional data transceivers are used. In this paper, we present a low-power, high-speed source-synchronous link transceiver which enables a factor 3.3 reduction in link power together with an 80% increase in data-rate. A low-swing capacitive pre-emphasis transmitter in combination with a double-tail sense-amplifier enable speeds in excess of 9 Gb/s over a 2 mm twisted differential interconnect, while consuming only 130 fJ/transition without the need for an additional supply. Multiple transceivers can be connected back-to-back to create a source-synchronous transceiver-chain with a wave-pipelined clock, operating with 6sigma offset reliability at 5 Gb/s

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.Siirretty Doriast

Low-swing signaling for energy efficient on-chip networks

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2011.Cataloged from PDF version of thesis.Includes bibliographical references (p. 65-69).On-chip networks have emerged as a scalable and high-bandwidth communication fabric in many-core processor chips. However, the energy consumption of these networks is becoming comparable to that of computation cores, making further scaling of core counts difficult. This thesis makes several contributions to low-swing signaling circuit design for the energy efficient on-chip networks in two separate projects: on-chip networks optimized for one-to-many multicasts and broadcasts, and link designs that allow on-chip networks to approach an ideal interconnection fabric. A low-swing crossbar switch, which is based on tri-state Reduced-Swing Drivers (RSDs), is presented for the first project. Measurement results of its test chip fabricated in 45nm SOI CMOS show that the tri-state RSD-based crossbar enables 55% power savings as compared to an equivalent full-swing crossbar and link. Also, the measurement results show that the proposed crossbar allows the broadcast-optimized on-chip networks using a single pipeline stage for physical data transmission to operate at 21% higher data rate, when compared with the full-swing networks. For the second project, two clockless low-swing repeaters, a Self-Resetting Logic Repeater (SRLR) and a Voltage-Locked Repeater (VLR), have been proposed and analyzed in simulation only. They both require no reference clock, differential signaling, and bias current. Such digital-intensive properties enable them to approach energy and delay performance of a point-to-point interconnect of variable lengths. Simulated in 45nm SOI CMOS, the 10mm SRLR featured with high energy efficiency consumes 338fJ/b at 5.4Gb/s/ch while the 10mm VLR raises its data rate up to 16.OGb/s/ch with 427fJ/b.by Sunghyun Park.S.M

A Survey Addressing on High Performance On-Chip VLSI Interconnect

With the rapid increase in transmission speeds of communication systems, the demand for very high-speed lowpower VLSI circuits is on the rise. Although the performance of CMOS technologies improves notably with scaling, conventional CMOS circuits cannot simultaneously satisfy the speed and power requirements of these applications. In this paper we survey the state of the art of on-chip interconnect techniques for improving performance, power and delay optimization and also comparative analysis of various techniques for high speed design have been discussed

Preliminary candidate advanced avionics system for general aviation

An integrated avionics system design was carried out to the level which indicates subsystem function, and the methods of overall system integration. Sufficient detail was included to allow identification of possible system component technologies, and to perform reliability, modularity, maintainability, cost, and risk analysis upon the system design. Retrofit to older aircraft, availability of this system to the single engine two place aircraft, was considered

Compressed Passive Macromodeling

This paper presents an approach for the extraction of passive macromodels of large-scale interconnects from their frequency-domain scattering responses. Here, large scale is intended both in terms of number of electrical ports and required dynamic model order. For such structures, standard approaches based on rational approximation via vector fitting and passivity enforcement via model perturbation may fail because of excessive computational requirements, both in terms of memory size and runtime. Our approach addresses this complexity by first reducing the redundancy in the raw scattering responses through a projection and approximation process based on a truncated singular value decomposition. Then we formulate a compressed rational fitting and passivity enforcement framework which is able to obtain speedup factors up to 2 and 3 orders of magnitude with respect to standard approaches, with full control over the approximation errors. Numerical results on a large set of benchmark cases demonstrate the effectiveness of the proposed techniqu