Integrated CMOS Energy Harvesting Converter with Digital Maximum Power Point Tracking for a Portable Thermophotovoltaic Power Generator

This paper presents an integrated maximum power point tracking system for use with a thermophotovoltaic (TPV) portable power generator. The design, implemented in 0.35 μm CMOS technology, consists of a low-power control stage and a dc-dc boost power stage with soft-switching capability. With a nominal input voltage of 1 V, and an output voltage of 4 V, we demonstrate a peak conversion efficiency under nominal conditions of over 94% (overall peak efficiency over 95%), at a power level of 300 mW. The control stage uses lossless current sensing together with a custom low-power time-based ADC to minimize control losses. The converter employs a fully integrated digital implementation of a peak power tracking algorithm, and achieves a measured tracking efficiency above 98%. A detailed study of achievable efficiency versus inductor size is also presented, with calculated and measured results.Interconnect Focus Center (United States. Defense Advanced Research Projects Agency and Semiconductor Research Corporation

CMOS indoor light energy harvesting system for wireless sensing applications

Dissertação para obtenção do Grau de Doutor em Engenharia Electrotécnica e de ComputadoresThis research thesis presents a micro-power light energy harvesting system for indoor environments. Light energy is collected by amorphous silicon photovoltaic (a-Si:H PV) cells, processed by a switched-capacitor (SC) voltage doubler circuit with maximum power point tracking (MPPT), and finally stored in a large capacitor. The MPPT Fractional Open Circuit Voltage (VOC) technique is implemented by an asynchronous state machine (ASM) that creates and, dynamically, adjusts the clock frequency of the step-up SC circuit, matching the input impedance of the SC circuit to the maximum power point (MPP) condition of the PV cells. The ASM has a separate local power supply to make it robust against load variations. In order to reduce the area occupied by the SC circuit, while maintaining an acceptable efficiency value, the SC circuit uses MOSFET capacitors with a charge reusing scheme for the bottom plate parasitic capacitors. The circuit occupies an area of 0.31 mm2 in a 130 nm CMOS technology. The system was designed in order to work under realistic indoor light intensities. Experimental results show that the proposed system, using PV cells with an area of 14 cm2, is capable of starting-up from a 0 V condition, with an irradiance of only 0.32 W/m2. After starting-up, the system requires an irradiance of only 0.18 W/m2 (18 mW/cm2) to remain in operation. The ASM circuit can operate correctly using a local power supply voltage of 453 mV, dissipating only 0.085 mW. These values are, to the best of the authors’ knowledge, the lowest reported in the literature. The maximum efficiency of the SC converter is 70.3% for an input power of 48 mW, which is comparable with reported values from circuits operating at similar power levels.Portuguese Foundation for Science and Technology (FCT/MCTES), under project PEst-OE/EEI/UI0066/2011, and to the CTS multiannual funding, through the PIDDAC Program funds. I am also very grateful for the grant SFRH/PROTEC/67683/2010, financially supported by the IPL – Instituto Politécnico de Lisboa

Inductively Coupled CMOS Power Receiver For Embedded Microsensors

Inductively coupled power transfer can extend the lifetime of embedded microsensors that save costs, energy, and lives. To expand the microsensors' functionality, the transferred power needs to be maximized. Plus, the power receiver needs to handle wide coupling variations in real applications. Therefore, the objective of this research is to design a power receiver that outputs the highest power for the widest coupling range. This research proposes a switched resonant half-bridge power stage that adjusts both energy transfer frequency and duration so the output power is maximally high. A maximum power point (MPP) theory is also developed to predict the optimal settings of the power stage with 98.6% accuracy. Finally, this research addresses the system integration challenges such as synchronization and over-voltage protection. The fabricated self-synchronized prototype outputs up to 89% of the available power across 0.067%~7.9% coupling range. The output power (in percentage of available power) and coupling range are 1.3× and 13× higher than the comparable state of the arts.Ph.D

Architectures and circuits for low-voltage energy conversion and applications in renewable energy and power management

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2012.Cataloged from PDF version of thesis.Includes bibliographical references (p. 337-343).In this thesis we seek to develop smaller, less expensive, and more efficient power electronics. We also investigate emerging applications where the proper implementation of these new types of power converters can have a significant impact on the overall system performance. We have developed a new two-stage dc-dc converter architecture suitable for low-voltage CMOS power delivery. The architecture, which combines the benefits of switched-capacitor and inductor-based converters, achieves both large voltage step-down and high switching frequency, while maintaining good efficiency. We explore the benefits of a new soft-charging technique that drastically reduces the major loss mechanism in switched-capacitor converters, and we show experimental results from a 5-to-1 V, 0.8 W integrated dc-dc converter developed in 180 nm CMOS technology. The use of power electronics to increase system performance in a portable thermophotovoltaic power generator is also investigated in this thesis. We show that mechanical non-idealities in a MEMS fabricated energy conversion device can be mitigated with the help of low-voltage distributed maximum power point tracking (MPPT) dc-dc converters. As part of this work, we explore low power control and sensing architectures, and present experimental results of a 300 mW integrated MPPT developed in 0.35 um CMOS with all power, sensing and control circuitry on chip. The final piece of this thesis investigates the implementation of distributed power electronics in solar photovoltaic applications. We explore the benefits of small, intelligent power converters integrated directly into the solar panel junction box to enhance overall energy capture in real-world scenarios. To this end, we developed a low-cost, high efficiency (>98%) power converter that enables intelligent control and energy conversion at the sub-panel level. Experimental field measurements show that the solution can provide up to a 35% increase in panel output power during partial shading conditions compared to current state-of-the-art solutions.by Robert C. N. Pilawa-Podgurski.Ph.D

Electrifying catheters with light

Smart minimally invasive devices face a connectivity challenge. An example is found in intracardiac echocardiography where the signal transmission and supply of power at the distal end require many thin and fragile wires in order to keep the catheter slim and flexible. We have built a fully functional bench-top prototype to demonstrate that electrical wires may be replaced by optical fibers. The prototype is immediately scalable to catheter dimensions. The absence of conductors will provide intrinsic galvanic isolation as well as radio frequency (RF) and magnetic resonance imaging (MRI) compatibility. Using optical fibers, we show signal transfer of synthetic aperture ultrasound images as well as photo-voltaic conversion to supply all electronics. The simple design utilizes only off the shelf components and holds a promise of cost effectiveness which may be pivotal for translation of these advanced devices into the clinic

Design of programmable matter

Thesis (S.M.)--Massachusetts Institute of Technology, School of Architecture and Planning, Program in Media Arts and Sciences, 2008.This electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.Includes bibliographical references (leaves 115-119).Programmable matter is a proposed digital material having computation, sensing, actuation, and display as continuous properties active over its whole extent. Programmable matter would have many exciting applications, like paintable displays, shape-changing robots and tools, rapid prototyping, and sculpture-based haptic interfaces. Programmable matter would be composed of millimeter-scale autonomous microsystem particles, without internal moving parts, bound by electromagnetic forces or an adhesive binder. Particles can dissipate 10 mW heat, and store 6 J energy in an internal zinc-air battery. Photovoltaic cells provide 300 [mu]W outdoors and 3.0 [mu]W indoors. Painted systems can store battery reactants in the paint binder; 6 J / mm3 can be stored, and diffusion is fast enough to transport reactants to the particles. Capacitive power transfer is an efficient method to transfer power to sparse, randomly placed particles. Power from capacitive transfer is proportional to VDD 2: 100[mu]W at 3.3V and 12 mW at 35V. Inter-particle communication is possible via optical, near-field, and far-field electromagnetic systems. Optical systems allow communication with low area (sub-mm) particles, and 24 pJ/bit. Near-field electromagnetic gives precisely controlled neighborhoods, localization capability, and 37 pJ/bit. Far-field radio communication between widely spaced particles may be possible at 60 GHz; antennas that fit inside 1 mm3 exist; complete transceivers do not. A 32-bit CPU uses less than 0.26 mm2 die area, 256K x 8 SRAM uses 1.1 mm2, and 256K x 8 FLASH uses 0.32 mm2. Direct-drive electric and magnetic field systems allow actuation without moving parts inside the particles. Magnetic surface-drive motors designed for operation without bearings are not power-efficient, and parasitic interactions between permanent magnets may limit their usefulness at millimeter particle dimensions. Electrostatic surface-drive motors are power-efficient, but practical only at particle dimensions below a few millimeters. We constructed a prototype paintable display; a distributed PostScript rendering system with 1000 randomly-placed 3.4 cm nodes, each with a CPU, IR communications, and LED. The system is used to render the letter "A." We present a design, not yet constructed, for a literal paintable display, with 1.0 mm rendering particles, each with a microprocessor and memory, and 110 [mu]m display particles, with tri-color LED's and simpler circuitry. Storage of zinc-air battery reactants in the paint binder would provide an 8 hour battery life, and capacitive power distribution would allow continuous operation. We constructed a prototype sliding-cube modular robot, with 3.4 cm nodes. The system uses magnetic surface-drive actuation. We demonstrate horizontal lattice-unit translation. We describe a design, not yet constructed, for a sliding-cube modular robot with 2 mm nodes. The cubes use standard-process CMOS IC's, inserted into a cubic space frame and wire-bonded together. Arrays of passivated electrodes, 1 [mu]m from the surface of the cubes, are used for electrostatic surface-drive actuation, zero-power latching, power transfer, localization, and communication. The design allows actuation from any contacting position. Energy is stored in a standard SMT capacitor inside each node, which is recharged by power transfer through chains of contacting nodes.by Ara N. Knaian.S.M

Transfer print techniques for heterogeneous integration of photonic components

The essential functionality of photonic and electronic devices is contained in thin surface layers leaving the substrate often to play primarily a mechanical role. Layer transfer of optimised devices or materials and their heterogeneous integration is thus a very attractive strategy to realise high performance, low-cost circuits for a wide variety of new applications. Additionally, new device configurations can be achieved that could not otherwise be realised. A range of layer transfer methods have been developed over the years including epitaxial lift-off and wafer bonding with substrate removal. Recently, a new technique called transfer printing has been introduced which allows manipulation of small and thin materials along with devices on a massively parallel scale with micron scale placement accuracies to a wide choice of substrates such as silicon, glass, ceramic, metal and polymer. Thus, the co-integration of electronics with photonic devices made from compound semiconductors, silicon, polymer and new 2D materials is now achievable in a practical and scalable method. This is leading to exciting possibilities in microassembly. We review some of the recent developments in layer transfer and particularly the use of the transfer print technology for enabling active photonic devices on rigid and flexible foreign substrates

Bidirectional Neural Interface Circuits with On-Chip Stimulation Artifact Reduction Schemes

Bidirectional neural interfaces are tools designed to “communicate” with the brain via recording and modulation of neuronal activity. The bidirectional interface systems have been adopted for many applications. Neuroscientists employ them to map neuronal circuits through precise stimulation and recording. Medical doctors deploy them as adaptable medical devices which control therapeutic stimulation parameters based on monitoring real-time neural activity. Brain-machine-interface (BMI) researchers use neural interfaces to bypass the nervous system and directly control neuroprosthetics or brain-computer-interface (BCI) spellers. In bidirectional interfaces, the implantable transducers as well as the corresponding electronic circuits and systems face several challenges. A high channel count, low power consumption, and reduced system size are desirable for potential chronic deployment and wider applicability. Moreover, a neural interface designed for robust closed-loop operation requires the mitigation of stimulation artifacts which corrupt the recorded signals. This dissertation introduces several techniques targeting low power consumption, small size, and reduction of stimulation artifacts. These techniques are implemented for extracellular electrophysiological recording and two stimulation modalities: direct current stimulation for closed-loop control of seizure detection/quench and optical stimulation for optogenetic studies. While the two modalities differ in their mechanisms, hardware implementation, and applications, they share many crucial system-level challenges. The first method aims at solving the critical issue of stimulation artifacts saturating the preamplifier in the recording front-end. To prevent saturation, a novel mixed-signal stimulation artifact cancellation circuit is devised to subtract the artifact before amplification and maintain the standard input range of a power-hungry preamplifier. Additional novel techniques have been also implemented to lower the noise and power consumption. A common average referencing (CAR) front-end circuit eliminates the cross-channel common mode noise by averaging and subtracting it in analog domain. A range-adapting SAR ADC saves additional power by eliminating unnecessary conversion cycles when the input signal is small. Measurements of an integrated circuit (IC) prototype demonstrate the attenuation of stimulation artifacts by up to 42 dB and cross-channel noise suppression by up to 39.8 dB. The power consumption per channel is maintained at 330 nW, while the area per channel is only 0.17 mm2. The second system implements a compact headstage for closed-loop optogenetic stimulation and electrophysiological recording. This design targets a miniaturized form factor, high channel count, and high-precision stimulation control suitable for rodent in-vivo optogenetic studies. Monolithically integrated optoelectrodes (which include 12 µLEDs for optical stimulation and 12 electrical recording sites) are combined with an off-the-shelf recording IC and a custom-designed high-precision LED driver. 32 recording and 12 stimulation channels can be individually accessed and controlled on a small headstage with dimensions of 2.16 x 2.38 x 0.35 cm and mass of 1.9 g. A third system prototype improves the optogenetic headstage prototype by furthering system integration and improving power efficiency facilitating wireless operation. The custom application-specific integrated circuit (ASIC) combines recording and stimulation channels with a power management unit, allowing the system to be powered by an ultra-light Li-ion battery. Additionally, the µLED drivers include a high-resolution arbitrary waveform generation mode for shaping of µLED current pulses to preemptively reduce artifacts. A prototype IC occupies 7.66 mm2, consumes 3.04 mW under typical operating conditions, and the optical pulse shaping scheme can attenuate stimulation artifacts by up to 3x with a Gaussian-rise pulse rise time under 1 ms.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147674/1/mendrela_1.pd

Spectrum-Dependent Photovoltaic Energy Harvesting.

Heterojunctions based on II-VI materials can be used to increase the efficiency of multi-junction solar cells, and may also offer the opportunity to realize next generation approaches such as the intermediate-band solar cell based on highly-mismatched alloys. One material of particular interest is ZnTe:O where IB solar energy conversion has been demonstrated. Efficient doping in many II-VI materials, however, is often a major obstacle to achieving high-quality junction diodes. In this work, studies of n-ZnSe/p-ZnTe heterojunction solar cells grown by molecular beam epitaxy will be reported. Limitations on the open-circuit voltage of p-ZnTe/n-ZnSe heterojunction solar cells are studied via current-voltage measurements under solar concentration and at variable temperature. The open-circuit voltage reaches a maximum value of 1.95 V at 77 K and 199 suns. The open-circuit voltage shows good agreement with the calculated built-in potential of 2.00 V at 77 K. These results suggest that the open-circuit voltage is limited by heterojunction band offsets associated with the type-II heterojunction band lineup, rather than the bandgap energy of the ZnTe absorber material. Low-power photovoltaic energy harvesting allows for the deployment of fully autonomous small-scale sensors in environments not previously possible. Indoor lighting is one of those environments where the illumination intensity is typically below 1,000 lx and the spectrum is narrowly centered in the visible region. The theoretical efficiency and electrical performance of photovoltaics under typical indoor lighting conditions are analyzed. Commercial crystalline Si, amorphous Si, and fabricated GaAs and Al0.2Ga0.8As photovoltaic cells were experimentally measured under simulated AM 1.5 solar irradiation and indoor illumination conditions using a white phosphor light-emitting diode to study the effects of input spectra and illuminance on performance. The Al0.2Ga0.8As cells demonstrated the highest performance with a power conversion efficiency of 21%, with open0circuit voltages >0.65 V under low lighting conditions. The GaAs and Al0.2Ga0.8As cells each provided a power density of ~100 nW/mm2 or more at 250 lx, sufficient for the perpetual operation of present-day low-power mm-scale wireless sensor nodes. The path for achieving large light harvesting efficiencies will be discussed as well as the implementation of these photovoltaic cells for mm-scale sensing applications.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/120752/1/asteran_1.pd

Energy Harvesting and Energy Storage Systems

This book discuss the recent developments in energy harvesting and energy storage systems. Sustainable development systems are based on three pillars: economic development, environmental stewardship, and social equity. One of the guiding principles for finding the balance between these pillars is to limit the use of non-renewable energy sources