Spatial networks with wireless applications

Many networks have nodes located in physical space, with links more common between closely spaced pairs of nodes. For example, the nodes could be wireless devices and links communication channels in a wireless mesh network. We describe recent work involving such networks, considering effects due to the geometry (convex,non-convex, and fractal), node distribution, distance-dependent link probability, mobility, directivity and interference.Comment: Review article- an amended version with a new title from the origina

Performance and energy efficiency in wireless self-organized networks

fi=vertaisarvioitu|en=peerReviewed

Achieving Non-Zero Information Velocity in Wireless Networks

In wireless networks, where each node transmits independently of other nodes in the network (the ALOHA protocol), the expected delay experienced by a packet until it is successfully received at any other node is known to be infinite for signal-to-interference-plus-noise-ratio (SINR) model with node locations distributed according to a Poisson point process. Consequently, the information velocity, defined as the limit of the ratio of the distance to the destination and the time taken for a packet to successfully reach the destination over multiple hops, is zero, as the distance tends to infinity. A nearest neighbor distance based power control policy is proposed to show that the expected delay required for a packet to be successfully received at the nearest neighbor can be made finite. Moreover, the information velocity is also shown to be non-zero with the proposed power control policy. The condition under which these results hold does not depend on the intensity of the underlying Poisson point process.Comment: to appear in Annals of Applied Probabilit

HWN* Mobility Management Considering QoS, Optimisation and Cross Layer Issues

In this paper, we address mobility management for 4th generation heterogeneous networks from a quality of service (QoS), optimisation and cross layer design perspective. Users are classified as high profile, normal profile and low profile according to their differentiated service requirements. Congestion avoidance control and adaptive handover mechanisms are implemented for efficient cooperation within the mobile heterogeneous network environment consisting of a TDMA network, ad hoc network and relay nodes. A previous proposed routing algorithm is also revised to include mobility management

Effect of steel fibre volume fraction on thermal performance of lightweight foamed mortar (LFM) at ambient temperature

Lightweight foamed mortar (LFM) has grow into utmost commercial building material in the construction industry for non-structural and semi-structural applications owing to its reduced self-weight, flowability, stability and excellent thermal insulation properties. Hence, this study was conducted with the aims to develop an alternative for conventional concrete bricks and blocks for non-structural and semi-structural applications of masonry. Lightweight foamed mortar (LFM) is either a cement paste or mortar, relegated as lightweight concrete, in which suitable foaming agent entraps the air-voids in mortar. It therefore has a wide range of applications such as material for wall blocks or panels, floor & roof screeds, trench reinstatement, road foundations and voids filling. This research focuses on experimental investigation of thermal properties of LFM with inclusion of relatively low volume fraction (0.2% and 0.4%) of steel fibre at ambient temperature. There are three parameters will be scrutinized such as thermal conductivity, thermal diffusivity as well as the specific heat capacity. There are two densities of 600kg/m3 and 1200kg/m3 had been cast and tested. The mix design proportion of LFM used for cement, aggregate and water ratio was 1: 1.5:0.45. The experimental results had indicated that the thermal conductivity, thermal diffusivity and specific heat value slightly higher than control mix due to the addition of steel fibres. For instance, thermal conductivity, diffusivity and specific heat of 600 kg/m3 density control mix were 0.212W/mK, 0.477mm2/s and 545 J/kg◦C respectively. When 0.2% volume fraction of steel fiber was added in the mix of 600 kg/m3 density, the value of thermal conductivity, diffusivity and specific heat were increased to 0.235W/mK, 0.583mm2/s and 578 J/kg◦C correspondingly. This is due to the characteristic of the steel fibre application in which steel fibre is good as heat conductor and excellent in absorbing heat. Therefore there is a potential of utilizing steel fiber in cement based material like LFM for components that needs excellent heat absorption capacity