LTE RSRP, RSRQ, RSSNR and local topography profile data for RF propagation planning and network optimization in an urban propagation environment

In the design of 5G cellular communication to guarantee quality signal reception at every point within a coverage area, fundamental knowledge of the channel propagation characteristics is vital. A correct knowledge of electromagnetic wave propagation is required for efficient radio network planning and optimization. Propagation data are used extensively in network planning, particularly for conducting feasibility studies. Hence, measurement of accurate propagation models that predict how the channel varies as people move about is crucial. However, these measured data are often not widely available for channel characterization and propagation model development. In this data article, the Reference Signal Received Power (RSRP), Reference Signal Received Quality (RSRQ) and Reference Signal Signal to Noise Ratio (RSSNR) at various points in space which is covered by a Long-Term Evolution (LTE) marco base station operating at 2100 MHz located in Hatfield, Hertfordshire, United Kingdom were measured. Further, local topography profile data of the study area were extracted from a digital elevation model (DEM) to account for the features of the propagation environment. Correlation matrix and descriptive statistics of the measured LTE data along different routes are analyzed. The RSRP, RSRQ and RSSNR variation with transmitter (Tx) – receiver (Rx) separation distance along the routes are presented. The probability distribution and the DEM of LTE data measurement are likewise presented. The data provided in this article will facilitate research advancement in wireless channel characterization that accounts for local topography features in an urban propagation environment. Moreover, the data sets provided in this article can be extended using simulation-based analysis to extract spatial and temporal channel model parameters in urban cellular environments in the development of 5G channel propagation models.Peer reviewedFinal Published versio

Mesoscale mapping of sediment source hotspots for dam sediment management in data-sparse semi-arid catchments

Land degradation and water availability in semi-arid regions are interdependent challenges for management that are influenced by climatic and anthropogenic changes. Erosion and high sediment loads in rivers cause reservoir siltation and decrease storage capacity, which pose risk on water security for citizens, agriculture, and industry. In regions where resources for management are limited, identifying spatial-temporal variability of sediment sources is crucial to decrease siltation. Despite widespread availability of rigorous methods, approaches simplifying spatial and temporal variability of erosion are often inappropriately applied to very data sparse semi-arid regions. In this work, we review existing approaches for mapping erosional hotspots, and provide an example of spatial-temporal mapping approach in two case study regions. The barriers limiting data availability and their effects on erosion mapping methods, their validation, and resulting prioritization of leverage management areas are discussed.BMBF, 02WGR1421A-I, GROW - Verbundprojekt SaWaM: Saisonales Wasserressourcen-Management in Trockenregionen: Praxistransfer regionalisierter globaler Informationen, Teilprojekt 1DFG, 414044773, Open Access Publizieren 2019 - 2020 / Technische Universität Berli

Small business innovation research. Abstracts of completed 1987 phase 1 projects

Non-proprietary summaries of Phase 1 Small Business Innovation Research (SBIR) projects supported by NASA in the 1987 program year are given. Work in the areas of aeronautical propulsion, aerodynamics, acoustics, aircraft systems, materials and structures, teleoperators and robotics, computer sciences, information systems, spacecraft systems, spacecraft power supplies, spacecraft propulsion, bioastronautics, satellite communication, and space processing are covered

Bridges Structural Health Monitoring and Deterioration Detection Synthesis of Knowledge and Technology

INE/AUTC 10.0

Measurements, processing functions and laboratory test-bed experiments for evaluating diversity in broadcast network

This paper presents a test-bed development and measurement plan for evaluating transmit diversity and on-channel repeaters in the Digital Video Broadcasting Network. Transmit diversity reduces the complexity and improves the power consumption of the personal receiving devices by enhancing the transmission of signals in NLOS cluttered environments. It is more practical than receive diversity due to the difficulty of locating two receive antennas far enough apart in a small mobile device. The on-channel repeater is to extend the coverage of the DVB-T/H network in areas where services are inaccessible by receiving the DVB-T/H signals off air, amplifying and then retransmitting it on the same frequency as received. Test service scenarios were developed to illustrate the benefits of such technologies so that effectiveness can be researched in a variety of service and terrain scenarios using purpose built test systems.The work presented in this paper was supported by the European Commission IST project PLUTO

Efficient DSP and Circuit Architectures for Massive MIMO: State-of-the-Art and Future Directions

Massive MIMO is a compelling wireless access concept that relies on the use of an excess number of base-station antennas, relative to the number of active terminals. This technology is a main component of 5G New Radio (NR) and addresses all important requirements of future wireless standards: a great capacity increase, the support of many simultaneous users, and improvement in energy efficiency. Massive MIMO requires the simultaneous processing of signals from many antenna chains, and computational operations on large matrices. The complexity of the digital processing has been viewed as a fundamental obstacle to the feasibility of Massive MIMO in the past. Recent advances on system-algorithm-hardware co-design have led to extremely energy-efficient implementations. These exploit opportunities in deeply-scaled silicon technologies and perform partly distributed processing to cope with the bottlenecks encountered in the interconnection of many signals. For example, prototype ASIC implementations have demonstrated zero-forcing precoding in real time at a 55 mW power consumption (20 MHz bandwidth, 128 antennas, multiplexing of 8 terminals). Coarse and even error-prone digital processing in the antenna paths permits a reduction of consumption with a factor of 2 to 5. This article summarizes the fundamental technical contributions to efficient digital signal processing for Massive MIMO. The opportunities and constraints on operating on low-complexity RF and analog hardware chains are clarified. It illustrates how terminals can benefit from improved energy efficiency. The status of technology and real-life prototypes discussed. Open challenges and directions for future research are suggested.Comment: submitted to IEEE transactions on signal processin

Analysis of interference to cable television due to mobile usage in the Digital Dividend

The start of use of mobile applications in the 800 MHz band, which forms part of the ‘Digital Dividend’, will cause interference to TV signals under certain conditions. The new mobile applications (called LTE, Long Term Evolution) use frequencies also used in cable TV networks. This report examines how much interference may occur when providing digital television over cable networks

The NASA SBIR product catalog

The purpose of this catalog is to assist small business firms in making the community aware of products emerging from their efforts in the Small Business Innovation Research (SBIR) program. It contains descriptions of some products that have advanced into Phase 3 and others that are identified as prospective products. Both lists of products in this catalog are based on information supplied by NASA SBIR contractors in responding to an invitation to be represented in this document. Generally, all products suggested by the small firms were included in order to meet the goals of information exchange for SBIR results. Of the 444 SBIR contractors NASA queried, 137 provided information on 219 products. The catalog presents the product information in the technology areas listed in the table of contents. Within each area, the products are listed in alphabetical order by product name and are given identifying numbers. Also included is an alphabetical listing of the companies that have products described. This listing cross-references the product list and provides information on the business activity of each firm. In addition, there are three indexes: one a list of firms by states, one that lists the products according to NASA Centers that managed the SBIR projects, and one that lists the products by the relevant Technical Topics utilized in NASA's annual program solicitation under which each SBIR project was selected