Piezoceramics-based Devices for Active Balancing of Flexible Shafts

This paper focuses on vibration control of flexible shafts by means of rotorfixed piezoelectric materials. The target is to realize compact solutions for the suppression of problematic resonant vibration at so-called flexural critical speeds. For analysis, parametric finite element models of flexible rotors with piezoceramic sheets and strain or displacement sensors are developed, where the number of degrees of freedom is kept low. Several mechanisms which can destabilize flexible rotors are quantisized, such as rotor material damping, dissipation of currents induced in rotor-fixed piezoceramics and active feedback control proportional to rotor strain rates. The effectiveness of low frequency feedback and feedforward control for the suppression of the unbalance response is demonstrated using analytic and experimental results. Emphasis is on the interaction between the dynamics of the rotor and that of the connected electronic circuits. The experimental setup which is used for validation is a flexible shaft equipped with piezoceramic sheets and strain sensors. A slipring assembly is used to simplify measurements with, and control of, the sensors and actuators on the shaft and to facilitate the development of compact drive electronics

Modelling gas flow pressure gradients in Gelcast ceramic foam diesel particulate filters

New mathematical models are proposed that predict fluid flow pressure gradients in gelcast ceramic foam diesel exhaust particulate filters by considering the foam structure conceptually as serially connected orifices. The resulting multiple orifice mathematical (MOM) model is based on the sum of a viscous term derived from an extended Ergun model and the kinetic energy loss derived from the Bernoulli and conservation of mass equations. The MOM model was calibrated using experimental data obtained from measuring the air flowrate and pressure drop across a physical large-scale three-dimensional model of a cellular foam structure produced using rapid manufacturing techniques. The calibrated model was then validated using fluid flow data obtained from gelcast ceramic foam filters of various cell sizes and was found to require no empirical recalibration for each gelcast ceramic foam sample. The MOM model for clean filters was extended to predict pressure gradients of filters loaded with particulate matter (PM). The prediction of pressure gradients through gelcast ceramic filters using the MOM model for clean and PM-loaded cases was shown to be in reasonable agreement with experimental data. The models were finally applied to design a filter for a turbocharged, charge-cooled, 2.0 l, fourstroke, common rail, direct injection passenger car diesel engine

Fluid handling equipment: A compilation

Devices and techniques used in fluid-handling and vacuum systems are described. Section 1 presents several articles on fluid lines and tubing. Section 2 describes a number of components such as valves, filters, and regulators. The last section contains descriptions of a number of innovative fluid-handling systems

Micro-Electro-Mechanical-Systems (MEMS) and Fluid Flows

The micromachining technology that emerged in the late 1980s can provide micron-sized sensors and actuators. These micro transducers are able to be integrated with signal conditioning and processing circuitry to form micro-electro-mechanical-systems (MEMS) that can perform real-time distributed control. This capability opens up a new territory for flow control research. On the other hand, surface effects dominate the fluid flowing through these miniature mechanical devices because of the large surface-to-volume ratio in micron-scale configurations. We need to reexamine the surface forces in the momentum equation. Owing to their smallness, gas flows experience large Knudsen numbers, and therefore boundary conditions need to be modified. Besides being an enabling technology, MEMS also provide many challenges for fundamental flow-science research

3D Spinodal Decomposition in the Inertial Regime

We simulate late-stage coarsening of a 3D symmetric binary fluid using a lattice Boltzmann method. With reduced lengths and times l and t respectively (scales set by viscosity, density and surface tension) our data sets cover 1 < l 100 we find clear evidence of Furukawa's inertial scaling (l ~ t^{2/3}), although the crossover from the viscous regime (l ~ t) is very broad. Though it cannot be ruled out, we find no indication that Re is self-limiting (l ~ t^{1/2}) as proposed by M. Grant and K. R. Elder [Phys. Rev. Lett. 82, 14 (1999)].Comment: 4 pages, 3 eps figures, RevTex, minor changes to bring in line with published version. Mobility values added to Table