Channel equalization to achieve high bit rates in discrete multitone systems

textMulticarrier modulation (MCM) techniques such as orthogonal frequency division multiplexing (OFDM) and discrete multi-tone (DMT) modulation are attractive for high-speed data communications due to the ease with which MCM can combat channel dispersion. With all the benefits MCM could give, DMT modulation has an extra ability to perform dynamic bit loading, which has the potential to exploit fully the available bandwidth in a slowly time-varying channel. In broadband wireline communications, DMT modulation is standardized for asymmetric digital subscribe line (ADSL) and very-high-bit-rate digital subscriber line (VDSL) modems. ADSL and VDSL standards are used by telephone companies to provide high speed data service to residences and offices. In an ADSL receiver, an equalizer is required to compensate for the channel’s dispersion in the time domain and the channel’s distortion in the frequency domain of the transmitted waveform. This dissertation proposes design methods for linear equalizers to increase the bit rate of the connection. The methods are amenable to implementation on programmable fixed-point digital signal processors, which are employed in ADSL/VDSL transceivers. A conventional ADSL equalizer consists of a time-domain equalizer, a fast Fourier transform, and a frequency domain equalizer. The time domain equalizer (TEQ) is a finite impulse response filter that when coupled with a discretized channel produces an equivalent channel whose impulse response is shorter than that of the discretized channel. This channel shortening is required by the ADSL standards. In this dissertation, I first propose a linear phase TEQ design that exploits symmetry in existing eigen-filter approaches such as minimum mean square error(MMSE), maximum shortening signal to noise ratio (MSSNR) and minimum intersymbol interference (Min-ISI) equalizers. TEQs with symmetric coefficients can reach the same performance as non-symmetric ones with much lower training complexity. Second, I improve Min-ISI design. I reformulate the cost function to make long TEQs design feasible. I remove the dependency of transmission delay in order to reduce the complexity associated with delay optimization. The quantized weighting is introduced to further lower the complexity. I also propose an iterative optimization procedure of Min-ISI that completely avoids Cholesky decomposition hence is better suited for a fixed-point implementation. Finally I propose a dual-path TEQ structure, which designs a standard singleFIR TEQ to achieve good bit rate over the entire transmission bandwidth, and designs another FIR TEQ to improve the bit rate over a subset of subcarriers. Dualpath TEQ can be viewed as a special case of a complex valued filter bank structure that delivers the best bit rate of existing DMT equalizers. However, dual-path TEQ provides a very good tradeoff between achievable bit rate vs. implementation complexity on a programmable digital signal processor.Electrical and Computer Engineerin

Resource allocation technique for powerline network using a modified shuffled frog-leaping algorithm

Resource allocation (RA) techniques should be made efficient and optimized in order to enhance the QoS (power & bit, capacity, scalability) of high-speed networking data applications. This research attempts to further increase the efficiency towards near-optimal performance. RA’s problem involves assignment of subcarriers, power and bit amounts for each user efficiently. Several studies conducted by the Federal Communication Commission have proven that conventional RA approaches are becoming insufficient for rapid demand in networking resulted in spectrum underutilization, low capacity and convergence, also low performance of bit error rate, delay of channel feedback, weak scalability as well as computational complexity make real-time solutions intractable. Mainly due to sophisticated, restrictive constraints, multi-objectives, unfairness, channel noise, also unrealistic when assume perfect channel state is available. The main goal of this work is to develop a conceptual framework and mathematical model for resource allocation using Shuffled Frog-Leap Algorithm (SFLA). Thus, a modified SFLA is introduced and integrated in Orthogonal Frequency Division Multiplexing (OFDM) system. Then SFLA generated random population of solutions (power, bit), the fitness of each solution is calculated and improved for each subcarrier and user. The solution is numerically validated and verified by simulation-based powerline channel. The system performance was compared to similar research works in terms of the system’s capacity, scalability, allocated rate/power, and convergence. The resources allocated are constantly optimized and the capacity obtained is constantly higher as compared to Root-finding, Linear, and Hybrid evolutionary algorithms. The proposed algorithm managed to offer fastest convergence given that the number of iterations required to get to the 0.001% error of the global optimum is 75 compared to 92 in the conventional techniques. Finally, joint allocation models for selection of optima resource values are introduced; adaptive power and bit allocators in OFDM system-based Powerline and using modified SFLA-based TLBO and PSO are propose

Techniques en appui des formats de modulation avancés pour les futurs réseaux optiques

Les systèmes de communication optique avec des formats de modulation avancés sont actuellement l’un des sujets de recherche les plus importants dans le domaine de communication optique. Cette recherche est stimulée par les exigences pour des débits de transmission de donnée plus élevés. Dans cette thèse, on examinera les techniques efficaces pour la modulation avancée avec une détection cohérente, et multiplexage par répartition en fréquence orthogonale (OFDM) et multiples tonalités discrètes (DMT) pour la détection directe et la détection cohérente afin d’améliorer la performance de réseaux optiques. Dans la première partie, nous examinons la rétropropagation avec filtre numérique (DFBP) comme une simple technique d’atténuation de nonlinéarité d’amplificateur optique semiconducteur (SOA) dans le système de détection cohérente. Pour la première fois, nous démontrons expérimentalement l’efficacité de DFBP pour compenser les nonlinéarités générées par SOA dans un système de détection cohérente porteur unique 16-QAM. Nous comparons la performance de DFBP avec la méthode de Runge-Kutta quatrième ordre. Nous examinons la sensibilité de performance de DFBP par rapport à ses paramètres. Par la suite, nous proposons une nouvelle méthode d’estimation de paramètre pour DFBP. Finalement, nous démontrons la transmission de signaux de 16-QAM aux taux de 22 Gbaud sur 80km de fibre optique avec la technique d’estimation de paramètre proposée pour DFBP. Dans la deuxième partie, nous nous concentrons sur les techniques afin d’améliorer la performance des systèmes OFDM optiques en examinent OFDM optiques cohérente (CO-OFDM) ainsi que OFDM optiques détection directe (DDO-OFDM). Premièrement, nous proposons une combinaison de coupure et prédistorsion pour compenser les distorsions nonlinéaires d’émetteur de CO-OFDM. Nous utilisons une interpolation linéaire par morceaux (PLI) pour charactériser la nonlinéarité d’émetteur. Dans l’émetteur nous utilisons l’inverse de l’estimation de PLI pour compenser les nonlinéarités induites à l’émetteur de CO-OFDM. Deuxièmement, nous concevons des constellations irrégulières optimisées pour les systèmes DDO-OFDM courte distance en considérant deux modèles de bruit de canal. Nous démontrons expérimentalement 100Gb/s+ OFDM/DMT avec la détection directe en utilisant les constellations QAM optimisées. Dans la troisième partie, nous proposons une architecture réseaux optiques passifs (PON) avec DDO-OFDM pour la liaison descendante et CO-OFDM pour la liaison montante. Nous examinons deux scénarios pour l’allocations de fréquence et le format de modulation des signaux. Nous identifions la détérioration limitante principale du PON bidirectionnelle et offrons des solutions pour minimiser ses effets.Optical communication systems with advanced modulation formats are currently one of the major research focuses of the optical communication community. This research is driven by the ever-increasing demand for higher data transmission rates. In this thesis, we investigate efficient techniques for advanced modulation with coherent detection, and optical orthogonal frequency-division multiplexing (OFDM) and discrete multi-tone (DMT) for both direct detection and coherent detection to improve the performance of optical networks. In the first part, we investigate digital filter back-propagation (DFBP) as a simple semiconductor optical amplifier (SOA) nonlinearity mitigation technique in coherent detection systems. For the first time, we experimentally demonstrate effectiveness of DFBP in compensating for SOA-induced nonlinearities in a 16-ary quadrature amplitude modulation (16-QAM) singlecarrier coherent detection system. We compare performance of DFBP with Runge-Kutta fourth-order method. We examine sensitivity of DFBP performance to its parameters. Afterwards, we propose a novel parameter estimation method for DFBP. Finally, we demonstrate successful transmission of 22 Gbaud 16-QAM signals over 80 km fiber with the proposed parameter estimation technique for DFBP. In the second part, we concentrate on techniques to improve performance of optical OFDM systems, examining both coherent optical OFDM (CO-OFDM) and direct-detection optical OFDM (DDO-OFDM). First, we propose a combination of clipping and predistortion technique to compensate for CO-OFDM transmitter nonlinear distortions. We use piecewise linear interpolation (PLI) for characterizing the transmitter nonlinearity. At the transmitter, we use inverse of the PLI estimate to pre-compensate the nonlinearities induced at the COOFDM transmitter. Second, we design optimized non-square constellations for short-reach DDO-OFDM systems based on two channel noise models. We experimentally demonstrate 100 Gb/s+ OFDM/DMT with direct detection using the optimized QAM constellations. In the third part, we propose and experimentally demonstrate a passive optical network (PON) architecture with DDO-OFDM for the downlink and CO-OFDM for the uplink. We examine two scenarios for the occupied frequency and modulation format of the signals. We identify main limiting impairments of the bidirectional PON and provide solutions to minimize their effects

Superimposed training for single carrier transmission in future mobile communications

The amount of wireless devices and wireless traffic has been increasing exponentially for the last ten years. It is forecasted that the exponential growth will continue without saturation till 2020 and probably further. So far, network vendors and operators have tackled the problem by introducing new evolutions of cellular macro networks, where each evolution has increased the physical layer spectral efficiency. Unfortunately, the spectral efficiency of the physical layer is achieving the Shannon-Hartley limit and does not provide much room for improvement anymore. However, considering the overhead due to synchronization and channel estimation reference symbols in the context of physical layer spectral efficiency, we believe that there is room for improvement. In this thesis, we will study the potentiality of superimposed training methods, especially data-dependent superimposed training, to boost the spectral efficiency of wideband single carrier communications even further. The main idea is that with superimposed training we can transmit more data symbols in the same time duration as compared to traditional time domain multiplexed training. In theory, more data symbols means more data bits which indicates higher throughput for the end user. In practice, nothing is free. With superimposed training we encounter self-interference between the training signal and the data signal. Therefore, we have to look for iterative receiver structures to separate these two or to estimate both, the desired data signal and the interfering component. In this thesis, we initiate the studies to find out if we truly can improve the existing systems by introducing the superimposed training scheme. We show that in certain scenarios we can achieve higher spectral efficiency, which maps directly to higher user throughput, but with the cost of higher signal processing burden in the receiver. In addition, we provide analytical tools for estimating the symbol or bit error ratio in the receiver with a given parametrization. The discussion leads us to the conclusion that there still remains several open topics for further study when looking for new ways of optimizing the overhead of reference symbols in wireless communications. Superimposed training with data-dependent components may prove to provide extra throughput gain. Furthermore, the superimposed component may be used for, e.g., improved synchronization, low bit-rate signaling or continuous tracking of neighbor cells. We believe that the current systems could be improved by using the superimposed training collectively with time domain multiplexed training

Adaptive transmission techniques in wireless fading channels

Master'sMASTER OF ENGINEERIN

Spectrum and energy efficient digital modulation techniques for practical visible light communication systems

The growth in mobile data traffic is rapidly increasing in an unsustainable direction given the radio frequency (RF) spectrum limits. Visible light communication (VLC) offers a lucrative solution based on an alternative license-free frequency band that is safe to use and inexpensive to utilize. Improving the spectral and energy efficiency of intensity modulation and direct detection (IM/DD) systems is still an on-going challenge in VLC. The energy efficiency of inherently unipolar modulation techniques such as pulse-amplitude modulation discrete multitone modulation (PAM-DMT) and asymmetrically clipped optical orthogonal frequency division multiplexing (ACO-OFDM) degrades at high spectral efficiency. Two novel superposition modulation techniques are proposed in this thesis based on PAM-DMT and ACO-OFDM. In addition, a practical solution based on the computationally efficient augmented spectral efficiency discrete multi-tone (ASE-DMT) is proposed. The system performance of the proposed superposition modulation techniques offers significant electrical and optical power savings with up to 8 dB in the electrical signal-to-noise ratio (SNR) when compared with DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM). The theoretical bit error ratio (BER) performance bounds for all of the proposed modulation techniques are in agreement with the Monte-Carlo simulation results. The proposed superposition modulation techniques are promising candidates for spectrum and energy efficient IM/DD systems. Two experimental studies are presented for a VLC system based on DCO-OFDM with adaptive bit and energy loading. Micrometer-sized Gallium Nitride light emitting diode (m-LED) and light amplification by stimulated emission of radiation diode (LD) are used in these studies due to their high modulation bandwidth. Record data rates are achieved with a BER below the forward error correction (FEC) threshold at 7.91 Gb/s using the violet m-LED and at 15 Gb/s using the blue LD. These results highlight the potential of VLC systems in practical high speed communication solutions. An additional experimental study is demonstrated for the proposed superposition modulation techniques based on ASE-DMT. The experimentally achieved results confirm the theoretical and simulation based performance predictions of ASE-DMT. A significant gain of up to 17.33 dB in SNR is demonstrated at a low direct current (DC) bias. Finally, the perception that VLC systems cannot work under the presence of sunlight is addressed in this thesis. A complete framework is presented to evaluate the performance of VLC systems in the presence of solar irradiance at any given location and time. The effect of sunlight is investigated in terms of the degradations in SNR, data rate and BER. A reliable high speed communication system is achieved under the sunlight effect. An optical bandpass blue filter is shown to compensate for half of the reduced data rate in the presence of sunlight. This thesis demonstrates data rates above 1 Gb/s for a practical VLC link under strong solar illuminance measured at 50350 lux in clear weather conditions

Transmit and Receive Signal Processing for MIMO Terrestrial Broadcast Systems

[EN] Multiple-Input Multiple-Output (MIMO) technology in Digital Terrestrial Television (DTT) networks has the potential to increase the spectral efficiency and improve network coverage to cope with the competition of limited spectrum use (e.g., assignment of digital dividend and spectrum demands of mobile broadband), the appearance of new high data rate services (e.g., ultra-high definition TV - UHDTV), and the ubiquity of the content (e.g., fixed, portable, and mobile). It is widely recognised that MIMO can provide multiple benefits such as additional receive power due to array gain, higher resilience against signal outages due to spatial diversity, and higher data rates due to the spatial multiplexing gain of the MIMO channel. These benefits can be achieved without additional transmit power nor additional bandwidth, but normally come at the expense of a higher system complexity at the transmitter and receiver ends. The final system performance gains due to the use of MIMO directly depend on physical characteristics of the propagation environment such as spatial correlation, antenna orientation, and/or power imbalances experienced at the transmit aerials. Additionally, due to complexity constraints and finite-precision arithmetic at the receivers, it is crucial for the overall system performance to carefully design specific signal processing algorithms. This dissertation focuses on transmit and received signal processing for DTT systems using MIMO-BICM (Bit-Interleaved Coded Modulation) without feedback channel to the transmitter from the receiver terminals. At the transmitter side, this thesis presents investigations on MIMO precoding in DTT systems to overcome system degradations due to different channel conditions. At the receiver side, the focus is given on design and evaluation of practical MIMO-BICM receivers based on quantized information and its impact in both the in-chip memory size and system performance. These investigations are carried within the standardization process of DVB-NGH (Digital Video Broadcasting - Next Generation Handheld) the handheld evolution of DVB-T2 (Terrestrial - Second Generation), and ATSC 3.0 (Advanced Television Systems Committee - Third Generation), which incorporate MIMO-BICM as key technology to overcome the Shannon limit of single antenna communications. Nonetheless, this dissertation employs a generic approach in the design, analysis and evaluations, hence, the results and ideas can be applied to other wireless broadcast communication systems using MIMO-BICM.[ES] La tecnología de múltiples entradas y múltiples salidas (MIMO) en redes de Televisión Digital Terrestre (TDT) tiene el potencial de incrementar la eficiencia espectral y mejorar la cobertura de red para afrontar las demandas de uso del escaso espectro electromagnético (e.g., designación del dividendo digital y la demanda de espectro por parte de las redes de comunicaciones móviles), la aparición de nuevos contenidos de alta tasa de datos (e.g., ultra-high definition TV - UHDTV) y la ubicuidad del contenido (e.g., fijo, portable y móvil). Es ampliamente reconocido que MIMO puede proporcionar múltiples beneficios como: potencia recibida adicional gracias a las ganancias de array, mayor robustez contra desvanecimientos de la señal gracias a la diversidad espacial y mayores tasas de transmisión gracias a la ganancia por multiplexado del canal MIMO. Estos beneficios se pueden conseguir sin incrementar la potencia transmitida ni el ancho de banda, pero normalmente se obtienen a expensas de una mayor complejidad del sistema tanto en el transmisor como en el receptor. Las ganancias de rendimiento finales debido al uso de MIMO dependen directamente de las características físicas del entorno de propagación como: la correlación entre los canales espaciales, la orientación de las antenas y/o los desbalances de potencia sufridos en las antenas transmisoras. Adicionalmente, debido a restricciones en la complejidad y aritmética de precisión finita en los receptores, es fundamental para el rendimiento global del sistema un diseño cuidadoso de algoritmos específicos de procesado de señal. Esta tesis doctoral se centra en el procesado de señal, tanto en el transmisor como en el receptor, para sistemas TDT que implementan MIMO-BICM (Bit-Interleaved Coded Modulation) sin canal de retorno hacia el transmisor desde los receptores. En el transmisor esta tesis presenta investigaciones en precoding MIMO en sistemas TDT para superar las degradaciones del sistema debidas a diferentes condiciones del canal. En el receptor se presta especial atención al diseño y evaluación de receptores prácticos MIMO-BICM basados en información cuantificada y a su impacto tanto en la memoria del chip como en el rendimiento del sistema. Estas investigaciones se llevan a cabo en el contexto de estandarización de DVB-NGH (Digital Video Broadcasting - Next Generation Handheld), la evolución portátil de DVB-T2 (Second Generation Terrestrial), y ATSC 3.0 (Advanced Television Systems Commitee - Third Generation) que incorporan MIMO-BICM como clave tecnológica para superar el límite de Shannon para comunicaciones con una única antena. No obstante, esta tesis doctoral emplea un método genérico tanto para el diseño, análisis y evaluación, por lo que los resultados e ideas pueden ser aplicados a otros sistemas de comunicación inalámbricos que empleen MIMO-BICM.[CA] La tecnologia de múltiples entrades i múltiples eixides (MIMO) en xarxes de Televisió Digital Terrestre (TDT) té el potencial d'incrementar l'eficiència espectral i millorar la cobertura de xarxa per a afrontar les demandes d'ús de l'escàs espectre electromagnètic (e.g., designació del dividend digital i la demanda d'espectre per part de les xarxes de comunicacions mòbils), l'aparició de nous continguts d'alta taxa de dades (e.g., ultra-high deffinition TV - UHDTV) i la ubiqüitat del contingut (e.g., fix, portàtil i mòbil). És àmpliament reconegut que MIMO pot proporcionar múltiples beneficis com: potència rebuda addicional gràcies als guanys de array, major robustesa contra esvaïments del senyal gràcies a la diversitat espacial i majors taxes de transmissió gràcies al guany per multiplexat del canal MIMO. Aquests beneficis es poden aconseguir sense incrementar la potència transmesa ni l'ample de banda, però normalment s'obtenen a costa d'una major complexitat del sistema tant en el transmissor com en el receptor. Els guanys de rendiment finals a causa de l'ús de MIMO depenen directament de les característiques físiques de l'entorn de propagació com: la correlació entre els canals espacials, l'orientació de les antenes, i/o els desequilibris de potència patits en les antenes transmissores. Addicionalment, a causa de restriccions en la complexitat i aritmètica de precisió finita en els receptors, és fonamental per al rendiment global del sistema un disseny acurat d'algorismes específics de processament de senyal. Aquesta tesi doctoral se centra en el processament de senyal tant en el transmissor com en el receptor per a sistemes TDT que implementen MIMO-BICM (Bit-Interleaved Coded Modulation) sense canal de tornada cap al transmissor des dels receptors. En el transmissor aquesta tesi presenta recerques en precoding MIMO en sistemes TDT per a superar les degradacions del sistema degudes a diferents condicions del canal. En el receptor es presta especial atenció al disseny i avaluació de receptors pràctics MIMO-BICM basats en informació quantificada i al seu impacte tant en la memòria del xip com en el rendiment del sistema. Aquestes recerques es duen a terme en el context d'estandardització de DVB-NGH (Digital Video Broadcasting - Next Generation Handheld), l'evolució portàtil de DVB-T2 (Second Generation Terrestrial), i ATSC 3.0 (Advanced Television Systems Commitee - Third Generation) que incorporen MIMO-BICM com a clau tecnològica per a superar el límit de Shannon per a comunicacions amb una única antena. No obstant açò, aquesta tesi doctoral empra un mètode genèric tant per al disseny, anàlisi i avaluació, per la qual cosa els resultats i idees poden ser aplicats a altres sistemes de comunicació sense fils que empren MIMO-BICM.Vargas Paredero, DE. (2016). Transmit and Receive Signal Processing for MIMO Terrestrial Broadcast Systems [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/66081TESISPremiad