MIMOシステムにおける格子基底縮小を用いた信号検出法及びその応用に関する研究

Multiple-input multiple-output (MIMO) technology has attracted attention in wireless communications, since it provides signi cant increases in data throughput and the high spectral efficiency. MIMO systems employ multiple antennas at both ends of the wireless link, and hence can increase the data rate by transmitting multiple data streams. To exploit the potential gains o ered by MIMO, signal processing involved in a MIMO receiver requires a large computational complexity in order to achieve the optimal performance. In MIMO systems, it is usually required to detect signals jointly as multiple signals are transmitted through multiple signal paths between the transmitter and the receiver. This joint detection becomes the MIMO detection. The maximum likelihood (ML) detection (MLD) is known as the optimal detector in terms of minimizing bit error rate (BER). However, the complexity of MLD obstructs its practical implementation. The common linear detection such as zero-forcing (ZF) or minimum mean squared error (MMSE) o ers a remarkable complexity reduction with performance loss. The non-linear detection, e.g. the successive interference cancellation (SIC), detects each symbol sequentially withthe aid of cancellation operations which remove the interferences from the received signal. The BER performance is improved by using the SIC, but is still inferior to that of the ML detector with low complexity. Numerous suboptimal detection techniques have been proposed to approximately approach the ML performance with relatively lower complexity, such as sphere detection (SD) and QRM-MLD. To look for suboptimal detection algorithm with near optimal performance and a ordable complexity costs for MIMO gains faces a major challenge. Lattice-reduction (LR) is a promising technique to improve the performance of MIMO detection. The LR makes the column vectors of the channel state information (CSI) matrix close to mutually orthogonal. The following signal estimation of the transmitted signal applies the reduced lattice basis instead of the original lattice basis. The most popular LR algorithm is the well-known LLL algorithm, introduced by Lenstra, Lenstra, and Lov asz. Using this algorithm, the LR aided (LRA) detector achieves more reliable signal estimation and hence good BER performance. Combining the LLL algorithm with the conventional linear detection of ZF or MMSE can further improve the BER performance in MIMO systems, especially the LR-MMSE detection. The non-linear detection i.e. SIC based on LR (LR-SIC) is selected from many detection methods since it features the good BER performance. And ordering SIC based on LR (LR-OSIC) can further improve the BER performance with the costs of the implementation of the ordering but requires high computational complexity. In addition, list detection can also obtain much better performance but with a little high computational cost in terms of the list of candidates. However, the expected performance of the several detections isnot satis ed directly like the ML detector, in particular for the high modulation order or the large size MIMO system. This thesis presents our studies about lattice reduction aided detection and its application in MIMO system. Our studies focus on the evaluation of BER performance and the computational complexity. On the hand, we improve the detection algorithms to achieve the near-ML BER performance. On the other hand, we reduce the complexity of the useless computation, such as the exhaustive tree search. We mainly solve three problems existed in the conventional detection methods as - The MLD based on QR decomposition and M-algorithm (QRMMLD) is one solution to relatively reduce the complexity while retaining the ML performance. The number of M in the conventional QRM-MLD is de ned as the number of the survived branches in each detection layer of the tree search, which is a tradeo between complexity and performance. Furthermore, the value of M should be large enough to ensure that the correct symbols exist in the survived branches under the ill-conditioned channel, in particular for the large size MIMO system and the high modulation order. Hence the conventional QRM-MLD still has the problem of high complexity in the better-conditioned channel. - For the LRA MIMO detection, the detection errors are mainly generated from the channel noise and the quantization errors in the signal estimation stage. The quantization step applies the simple rounding operation, which often leads to the quantization error. If this error occurs in a row of the transmit signal, it has to propagate to many symbols in the subsequent signal estimation and result in degrading the BER performance. The conventional LRA MIMO detection has the quantization problem, which obtains less reliable signal estimation and leads to the BER performance loss. - Ordering the column vectors of the LR-reduced channel matrix brings large improvement on the BER performance of the LRSIC due to decreasing the error propagation. However, the improvement of the LR-OSIC is not su cient to approach the ML performance in the large size MIMO system, such as 8 8 MIMO system. Hence, the LR-OSIC detection cannot achieve the near-ML BER performance in the large size of MIMO system. The aim of our researches focuses on the detection algorithm, which provides near-ML BER performance with very low additional complexity. Therefore, we have produced various new results on low complexity MIMO detection with the ideas of lattice reduction aided detection and its application even for large size MIMO system and high modulation order. Our works are to solve the problems in the conventional MIMO detections and to improve the detection algorithms in the signal estimation. As for the future research, these detection schemes combined with the encoding technique lead to interesting and useful applications in the practical MIMO system or massive MIMO.電気通信大学201

Large-Scale MIMO Detection for 3GPP LTE: Algorithms and FPGA Implementations

Large-scale (or massive) multiple-input multiple-output (MIMO) is expected to be one of the key technologies in next-generation multi-user cellular systems, based on the upcoming 3GPP LTE Release 12 standard, for example. In this work, we propose - to the best of our knowledge - the first VLSI design enabling high-throughput data detection in single-carrier frequency-division multiple access (SC-FDMA)-based large-scale MIMO systems. We propose a new approximate matrix inversion algorithm relying on a Neumann series expansion, which substantially reduces the complexity of linear data detection. We analyze the associated error, and we compare its performance and complexity to those of an exact linear detector. We present corresponding VLSI architectures, which perform exact and approximate soft-output detection for large-scale MIMO systems with various antenna/user configurations. Reference implementation results for a Xilinx Virtex-7 XC7VX980T FPGA show that our designs are able to achieve more than 600 Mb/s for a 128 antenna, 8 user 3GPP LTE-based large-scale MIMO system. We finally provide a performance/complexity trade-off comparison using the presented FPGA designs, which reveals that the detector circuit of choice is determined by the ratio between BS antennas and users, as well as the desired error-rate performance.Comment: To appear in the IEEE Journal of Selected Topics in Signal Processin

Multi-Step Knowledge-Aided Iterative ESPRIT for Direction Finding

In this work, we propose a subspace-based algorithm for DOA estimation which iteratively reduces the disturbance factors of the estimated data covariance matrix and incorporates prior knowledge which is gradually obtained on line. An analysis of the MSE of the reshaped data covariance matrix is carried out along with comparisons between computational complexities of the proposed and existing algorithms. Simulations focusing on closely-spaced sources, where they are uncorrelated and correlated, illustrate the improvements achieved.Comment: 7 figures. arXiv admin note: text overlap with arXiv:1703.1052

An Iterative Soft Decision Based LR-Aided MIMO Detector

The demand for wireless and high-rate communication system is increasing gradually and multiple-input-multiple-output (MIMO) is one of the feasible solutions to accommodate the growing demand for its spatial multiplexing and diversity gain. However, with high number of antennas, the computational and hardware complexity of MIMO increases exponentially. This accumulating complexity is a paramount problem in MIMO detection system directly leading to large power consumption. Hence, the major focus of this dissertation is algorithmic and hardware development of MIMO decoder with reduced complexity for both real and complex domain, which can be a beneficial solution with power efficiency and high throughput. Both hard and soft domain MIMO detectors are considered. The use of lattice reduction (LR) algorithm and on-demand-child-expansion for the reduction of noise propagation and node calculation respectively are the two of the key features of our developed architecture, presented in this literature. The real domain iterative soft MIMO decoding algorithm, simulated for 4 × 4 MIMO with different modulation scheme, achieves 1.1 to 2.7 dB improvement over Lease Sphere Decoder (LSD) and more than 8x reduction in list size, K as well as complexity of the detector. Next, the iterative real domain K-Best decoder is expanded to the complex domain with new detection scheme. It attains 6.9 to 8.0 dB improvement over real domain K-Best decoder and 1.4 to 2.5 dB better performance over conventional complex decoder for 8 × 8 MIMO with 64 QAM modulation scheme. Besides K, a new adjustable parameter, Rlimit has been introduced in order to append re-configurability trading-off between complexity and performance. After that, a novel low-power hardware architecture of complex decoder is developed for 8 × 8 MIMO and 64 QAM modulation scheme. The total word length of only 16 bits has been adopted limiting the bit error rate (BER) degradation to 0.3 dB with K and Rlimit equal to 4. The proposed VLSI architecture is modeled in Verilog HDL using Xilinx and synthesized using Synopsys Design Vision in 45 nm CMOS technology. According to the synthesize result, it achieves 1090.8 Mbps throughput with power consumption of 580 mW and latency of 0.33 us. The maximum frequency the design proposed is 181.8 MHz. All of the proposed decoders mentioned above are bounded by the fixed K. Hence, an adaptive real domain K-Best decoder is further developed to achieve the similar performance with less K, thereby reducing the computational complexity of the decoder. It does not require accurate SNR measurement to perform the initial estimation of list size, K. Instead, the difference between the first two minimal distances is considered, which inherently eliminates complexity. In summary, a novel iterative K-Best detector for both real and complex domain with efficient VLSI design is proposed in this dissertation. The results from extensive simulation and VHDL with analysis using Synopsys tool are also presented for justification and validation of the proposed works

An Iterative Soft Decision Based LR-Aided MIMO Detector

The demand for wireless and high-rate communication system is increasing gradually and multiple-input-multiple-output (MIMO) is one of the feasible solutions to accommodate the growing demand for its spatial multiplexing and diversity gain. However, with high number of antennas, the computational and hardware complexity of MIMO increases exponentially. This accumulating complexity is a paramount problem in MIMO detection system directly leading to large power consumption. Hence, the major focus of this dissertation is algorithmic and hardware development of MIMO decoder with reduced complexity for both real and complex domain, which can be a beneficial solution with power efficiency and high throughput. Both hard and soft domain MIMO detectors are considered. The use of lattice reduction (LR) algorithm and on-demand-child-expansion for the reduction of noise propagation and node calculation respectively are the two of the key features of our developed architecture, presented in this literature. The real domain iterative soft MIMO decoding algorithm, simulated for 4 × 4 MIMO with different modulation scheme, achieves 1.1 to 2.7 dB improvement over Lease Sphere Decoder (LSD) and more than 8x reduction in list size, K as well as complexity of the detector. Next, the iterative real domain K-Best decoder is expanded to the complex domain with new detection scheme. It attains 6.9 to 8.0 dB improvement over real domain K-Best decoder and 1.4 to 2.5 dB better performance over conventional complex decoder for 8 × 8 MIMO with 64 QAM modulation scheme. Besides K, a new adjustable parameter, Rlimit has been introduced in order to append re-configurability trading-off between complexity and performance. After that, a novel low-power hardware architecture of complex decoder is developed for 8 × 8 MIMO and 64 QAM modulation scheme. The total word length of only 16 bits has been adopted limiting the bit error rate (BER) degradation to 0.3 dB with K and Rlimit equal to 4. The proposed VLSI architecture is modeled in Verilog HDL using Xilinx and synthesized using Synopsys Design Vision in 45 nm CMOS technology. According to the synthesize result, it achieves 1090.8 Mbps throughput with power consumption of 580 mW and latency of 0.33 us. The maximum frequency the design proposed is 181.8 MHz. All of the proposed decoders mentioned above are bounded by the fixed K. Hence, an adaptive real domain K-Best decoder is further developed to achieve the similar performance with less K, thereby reducing the computational complexity of the decoder. It does not require accurate SNR measurement to perform the initial estimation of list size, K. Instead, the difference between the first two minimal distances is considered, which inherently eliminates complexity. In summary, a novel iterative K-Best detector for both real and complex domain with efficient VLSI design is proposed in this dissertation. The results from extensive simulation and VHDL with analysis using Synopsys tool are also presented for justification and validation of the proposed works

Récepteur itératif pour les systèmes MIMO-OFDM basé sur le décodage sphérique : convergence, performance et complexité

Recently, iterative processing has been widely considered to achieve near-capacity performance and reliable high data rate transmission, for future wireless communication systems. However, such an iterative processing poses significant challenges for efficient receiver design. In this thesis, iterative receiver combining multiple-input multiple-output (MIMO) detection with channel decoding is investigated for high data rate transmission. The convergence, the performance and the computational complexity of the iterative receiver for MIMO-OFDM system are considered. First, we review the most relevant hard-output and soft-output MIMO detection algorithms based on sphere decoding, K-Best decoding, and interference cancellation. Consequently, a low-complexity K-best (LCK- Best) based decoder is proposed in order to substantially reduce the computational complexity without significant performance degradation. We then analyze the convergence behaviors of combining these detection algorithms with various forward error correction codes, namely LTE turbo decoder and LDPC decoder with the help of Extrinsic Information Transfer (EXIT) charts. Based on this analysis, a new scheduling order of the required inner and outer iterations is suggested. The performance of the proposed receiver is evaluated in various LTE channel environments, and compared with other MIMO detection schemes. Secondly, the computational complexity of the iterative receiver with different channel coding techniques is evaluated and compared for different modulation orders and coding rates. Simulation results show that our proposed approaches achieve near optimal performance but more importantly it can substantially reduce the computational complexity of the system. From a practical point of view, fixed-point representation is usually used in order to reduce the hardware costs in terms of area, power consumption and execution time. Therefore, we present efficient fixed point arithmetic of the proposed iterative receiver based on LC-KBest decoder. Additionally, the impact of the channel estimation on the system performance is studied. The proposed iterative receiver is tested in a real-time environment using the MIMO WARP platform.Pour permettre l’accroissement de débit et de robustesse dans les futurs systèmes de communication sans fil, les processus itératifs sont de plus considérés dans les récepteurs. Cependant, l’adoption d’un traitement itératif pose des défis importants dans la conception du récepteur. Dans cette thèse, un récepteur itératif combinant les techniques de détection multi-antennes avec le décodage de canal est étudié. Trois aspects sont considérés dans un contexte MIMOOFDM: la convergence, la performance et la complexité du récepteur. Dans un premier temps, nous étudions les différents algorithmes de détection MIMO à décision dure et souple basés sur l’égalisation, le décodage sphérique, le décodage K-Best et l’annulation d’interférence. Un décodeur K-best de faible complexité (LC-K-Best) est proposé pour réduire la complexité sans dégradation significative des performances. Nous analysons ensuite la convergence de la combinaison de ces algorithmes de détection avec différentes techniques de codage de canal, notamment le décodeur turbo et le décodeur LDPC en utilisant le diagramme EXIT. En se basant sur cette analyse, un nouvel ordonnancement des itérations internes et externes nécessaires est proposé. Les performances du récepteur ainsi proposé sont évaluées dans différents modèles de canal LTE, et comparées avec différentes techniques de détection MIMO. Ensuite, la complexité des récepteurs itératifs avec différentes techniques de codage de canal est étudiée et comparée pour différents modulations et rendement de code. Les résultats de simulation montrent que les approches proposées offrent un bon compromis entre performance et complexité. D’un point de vue implémentation, la représentation en virgule fixe est généralement utilisée afin de réduire les coûts en termes de surface, de consommation d’énergie et de temps d’exécution. Nous présentons ainsi une représentation en virgule fixe du récepteur itératif proposé basé sur le décodeur LC K-Best. En outre, nous étudions l’impact de l’estimation de canal sur la performance du système. Finalement, le récepteur MIMOOFDM itératif est testé sur la plateforme matérielle WARP, validant le schéma proposé

A Primer on MIMO Detection Algorithms for 5G Communication Network

In the recent past, demand for large use of mobile data has increased tremendously due to the proliferation of hand held devices which allows millions of people access to video streaming, VOIP and other internet related usage including machine to machine (M2M) communication. One of the anticipated attribute of the fifth generation (5G) network is its ability to meet this humongous data rate requirement in the order of 10s Gbps. A particular promising technology that can provide this desired performance if used in the 5G network is the massive multiple-input, multiple-output otherwise called the Massive MIMO. The use of massive MIMO in 5G cellular network where data rate of the order of 100x that of the current state of the art LTE-A is expected and high spectral efficiency with very low latency and low energy consumption, present a challenge in symbol/signal detection and parameter estimation as a result of the high dimension of the antenna elements required. One of the major bottlenecks in achieving the benefits of such massive MIMO systems is the problem of achieving detectors with realistic low complexity for such huge systems. We therefore review various MIMO detection algorithms aiming for low computational complexity with high performance and that scales well with increase in transmit antennas suitable for massive MIMO systems. We evaluate detection algorithms for small and medium dimension MIMO as well as a combination of some of them in order to achieve our above objectives. The review shows no single one detector can be said to be ideal for massive MIMO and that the low complexity with optimal performance detector suitable for 5G massive MIMO system is still an open research issue. A comprehensive review of such detection algorithms for massive MIMO was not presented in the literature which was achieved in this work

Reduced Receivers for Faster-than-Nyquist Signaling and General Linear Channels

Fast and reliable data transmission together with high bandwidth efficiency are important design aspects in a modern digital communication system. Many different approaches exist but in this thesis bandwidth efficiency is obtained by increasing the data transmission rate with the faster-than-Nyquist (FTN) framework while keeping a fixed power spectral density (PSD). In FTN consecutive information carrying symbols can overlap in time and in that way introduce a controlled amount of intentional intersymbol interference (ISI). This technique was introduced already in 1975 by Mazo and has since then been extended in many directions. Since the ISI stemming from practical FTN signaling can be of significant duration, optimum detection with traditional methods is often prohibitively complex, and alternative equalization methods with acceptable complexity-performance tradeoffs are needed. The key objective of this thesis is therefore to design reduced-complexity receivers for FTN and general linear channels that achieve optimal or near-optimal performance. Although the performance of a detector can be measured by several means, this thesis is restricted to bit error rate (BER) and mutual information results. FTN signaling is applied in two ways: As a separate uncoded narrowband communication system or in a coded scenario consisting of a convolutional encoder, interleaver and the inner ISI mechanism in serial concatenation. Turbo equalization where soft information in the form of log likelihood ratios (LLRs) is exchanged between the equalizer and the decoder is a commonly used decoding technique for coded FTN signals. The first part of the thesis considers receivers and arising stability problems when working within the white noise constraint. New M-BCJR algorithms for turbo equalization are proposed and compared to reduced-trellis VA and BCJR benchmarks based on an offset label idea. By adding a third low-complexity M-BCJR recursion, LLR quality is improved for practical values of M. M here measures the reduced number of BCJR computations for each data symbol. An improvement of the minimum phase conversion that sharpens the focus of the ISI model energy is proposed. When combined with a delayed and slightly mismatched receiver, the decoding allows a smaller M without significant loss in BER. The second part analyzes the effect of the internal metric calculations on the performance of Forney- and Ungerboeck-based reduced-complexity equalizers of the M-algorithm type for both ISI and multiple-input multiple-output (MIMO) channels. Even though the final output of a full-complexity equalizer is identical for both models, the internal metric calculations are in general different. Hence, suboptimum methods need not produce the same final output. Additionally, new models working in between the two extremes are proposed and evaluated. Note that the choice of observation model does not impact the detection complexity as the underlying algorithm is unaltered. The last part of the thesis is devoted to a different complexity reducing approach. Optimal channel shortening detectors for linear channels are optimized from an information theoretical perspective. The achievable information rates of the shortened models as well as closed form expressions for all components of the optimal detector of the class are derived. The framework used in this thesis is more general than what has been previously used within the area