A Low-Power, Reconfigurable, Pipelined ADC with Automatic Adaptation for Implantable Bioimpedance Applications

Biomedical monitoring systems that observe various physiological parameters or electrochemical reactions typically cannot expect signals with fixed amplitude or frequency as signal properties can vary greatly even among similar biosignals. Furthermore, advancements in biomedical research have resulted in more elaborate biosignal monitoring schemes which allow the continuous acquisition of important patient information. Conventional ADCs with a fixed resolution and sampling rate are not able to adapt to signals with a wide range of variation. As a result, reconfigurable analog-to-digital converters (ADC) have become increasingly more attractive for implantable biosensor systems. These converters are able to change their operable resolution, sampling rate, or both in order convert changing signals with increased power efficiency. Traditionally, biomedical sensing applications were limited to low frequencies. Therefore, much of the research on ADCs for biomedical applications focused on minimizing power consumption with smaller bias currents resulting in low sampling rates. However, recently bioimpedance monitoring has become more popular because of its healthcare possibilities. Bioimpedance monitoring involves injecting an AC current into a biosample and measuring the corresponding voltage drop. The frequency of the injected current greatly affects the amplitude and phase of the voltage drop as biological tissue is comprised of resistive and capacitive elements. For this reason, a full spectrum of measurements from 100 Hz to 10-100 MHz is required to gain a full understanding of the impedance. For this type of implantable biomedical application, the typical low power, low sampling rate analog-to-digital converter is insufficient. A different optimization of power and performance must be achieved. Since SAR ADC power consumption scales heavily with sampling rate, the converters that sample fast enough to be attractive for bioimpedance monitoring do not have a figure-of-merit that is comparable to the slower converters. Therefore, an auto-adapting, reconfigurable pipelined analog-to-digital converter is proposed. The converter can operate with either 8 or 10 bits of resolution and with a sampling rate of 0.1 or 20 MS/s. Additionally, the resolution and sampling rate are automatically determined by the converter itself based on the input signal. This way, power efficiency is increased for input signals of varying frequency and amplitude

Ring-oscillator with multiple transconductors for linear analog-to-digital conversion

This paper proposes a new circuit-based approach to mitigate nonlinearity in open-loop ring-oscillator-based analog-to-digital converters (ADCs). The approach consists of driving a current-controlled oscillator (CCO) with several transconductors connected in parallel with different bias conditions. The current injected into the oscillator can then be properly sized to linearize the oscillator, performing the inverse current-to-frequency function. To evaluate the approach, a circuit example has been designed in a 65-nm CMOS process, leading to a more than 3-ENOB enhancement in simulation for a high-swing differential input voltage signal of 800-mVpp, with considerable less complex design and lower power and expected area in comparison to state-of-the-art circuit based solutions. The architecture has also been checked against PVT and mismatch variations, proving to be highly robust, requiring only very simple calibration techniques. The solution is especially suitable for high-bandwidth (tens of MHz) medium-resolution applications (10–12 ENOBs), such as 5G or Internet-of-Things (IoT) devices.This research was funded by Project TEC2017-82653-R, Spain

Digitally Assisted ADCS.

This work involves the development of digital calibration techniques for Analogto- Digital Converters. According to the 2001 International Technology Roadmap for Semiconductors, improved ADC technology is a key factor in the development of present and future applications. The switched-capacitor (SC) pipeline technique is the most popular method of implementing moderate resolution ADCs. However the advantages of CMOS, which originally made SC circuits feasible, are being eroding by process scaling. Good switches and opamps are becoming increasingly difficult to design and the growing gate leakage of deep submicron MOSFETs is causing difficulty. Traditional ADC schemes do not work well with supply voltages of 1.8V and below. Furthermore, the performance required by present and future wireless and IT applications will not be met by the present day ADC circuits techniques. Bearing in mind the challenges associated with deep sub-micron analog circuitry a new calibration technique for folding ADCs has been developed. Since digital circuitry scales well, this calibration relies heavily on digital techniques. Hence it reduces the amount of analog design involved. As this folding ADC is dominated, in terms of both functionality and power, by digital circuitry, the performance of folding will improve when implemented in smaller geometry processes. An 8-bit, 500MS/s, digitally calibrated folding ADC was designed in TSMC 0.18mm. A second prototype, 9-bit 400MS/s, was designed in ST 90nm. This ADC uses novel folders to reduce thermal noise. The major accomplishments of this work are: · The creation of a new folding ADC architecture that is digitally dominated allowing large transistor mismatch to be tolerated so that small devices can be utilized in the signal path. · The development of modeling techniques, to investigate and analyze the effects of transistor mismatch, folder linearity and redundancy in ADCs. · The design of a new folder circuit topology that decreases the required power consumption for a given noise budget. · The design of a resistor ladder DAC that uses a unique resistor layout to allow any shape ladder to be designed.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/58426/1/ibogue_1.pd

Design Techniques for High-Performance SAR A/D Converters

The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs. ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption. Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s. The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology

Architectural Improvements Towards an Efficient 16-18 Bit 100-200 MSPS ADC

As Data conversion systems continue to improve in speed and resolution, increasing demands are placed on the performance of high-speed Analog to Digital Conversion systems. This work makes a survey about all these and proposes a suitable architecture in order to achieve the desired specifications of 100-200MS/s with 16-18 bit of resolution. The main architecture is based on paralleled structures in order to achieve high sampling rate and at the same time high resolution. In order to solve problems related to Time-interleaved architectures, an advanced randomization method was introduced. It combines randomization and spectral shaping of mismatches. With a simple low-pass filter the method can, compared to conventional randomization algorithms, improve the SFDR as well as the SINAD. The main advantage of this technique over previous ones is that, because the algorithm only need that ADCs are ordered basing on their time mismatches, the absolute accuracy of the mismatch identification method does not matter and, therefore, the requirements on the timing mismatch identification are very low. In addition to that, this correction system uses very simple algorithms able to correct not only for time but also for gain and offset mismatches

Carbon footprint of 3D-printed bone tissue engineering scaffolds: an life cycle assessment study

The bone tissue engineering scaffolds is one of the methods for repairing bone defects caused by various factors. According to modern tissue engineering technology, three-dimensional (3D) printing technology for bone tissue engineering provides a temporary basis for the creation of biological replacements. Through the generated 3D bone tissue engineering scaffolds from previous studies, the assessment to evaluate the environmental impact has shown less attention in research. Therefore, this paper is aimed to propose the Model of life cycle assessment (LCA) for 3D bone tissue engineering scaffolds of 3D gel-printing technology and presented the analysis technique of LCA from cradle-to-gate for assessing the environmental impacts of carbon footprint. Acrylamide (C3H5NO), citric acid (C6H8O7), N,N-Dimethylaminopropyl acrylamide (C8H16N2O), deionized water (H2O), and 2-Hydroxyethyl acrylate (C5H8O3) was selected as the material resources. Meanwhile, the 3D gel-printing technology was used as the manufacturing processes in the system boundary. The analysis is based on the LCA Model through the application of GaBi software. The environmental impact was assessed in the 3D gel-printing technology and it was obtained that the system shows the environmental impact of global warming potential (GWP). All of the emissions contributed to GWP have been identified such as emissions to air, freshwater, seawater, and industrial soil. The aggregation of GWP result in the stage of manufacturing process for input and output data contributed 47.6% and 32.5% respectively. Hence, the data analysis of the results is expected to use for improving the performance at the material and manufacturing process of the product life cycle

Pipeline analog-to-digital converters for wide-band wireless communications

During the last decade, the development of the analog electronics has been dictated by the enormous growth of the wireless communications. Typical for the new communication standards has been an evolution towards higher data rates, which allows more services to be provided. Simultaneously, the boundary between analog and digital signal processing is moving closer to the antenna, thus aiming for a software defined radio. For analog-to-digital converters (ADCs) of radio receivers this indicates higher sample rate, wider bandwidth, higher resolution, and lower power dissipation. The radio receiver architectures, showing the greatest potential to meet the commercial trends, include the direct conversion receiver and the super heterodyne receiver with an ADC sampling at the intermediate frequency (IF). The pipelined ADC architecture, based on the switched capacitor (SC) technique, has most successfully covered the widely separated resolution and sample rate requirements of these receiver architectures. In this thesis, the requirements of ADCs in both of these receiver architectures are studied using the system specifications of the 3G WCDMA standard. From the standard and from the limited performance of the circuit building blocks, design constraints for pipeline ADCs, at the architectural and circuit level, are drawn. At the circuit level, novel topologies for all the essential blocks of the pipeline ADC have been developed. These include a dual-mode operational amplifier, low-power voltage reference circuits with buffering, and a floating-bulk bootstrapped switch for highly-linear IF-sampling. The emphasis has been on dynamic comparators: a new mismatch insensitive topology is proposed and measurement results for three different topologies are presented. At the architectural level, the optimization of the ADCs in the single-chip direct conversion receivers is discussed: the need for small area, low power, suppression of substrate noise, input and output interfaces, etc. Adaptation of the resolution and sample rate of a pipeline ADC, to be used in more flexible multi-mode receivers, is also an important topic included. A 6-bit 15.36-MS/s embedded CMOS pipeline ADC and an 8-bit 1/15.36-MS/s dual-mode CMOS pipeline ADC, optimized for low-power single-chip direct conversion receivers with single-channel reception, have been designed. The bandwidth of a pipeline ADC can be extended by employing parallelism to allow multi-channel reception. The errors resulted from mismatch of parallel signal paths are analyzed and their elimination is presented. Particularly, an optimal partitioning of the resolution between the stages, and the number of parallel channels, in time-interleaved ADCs are derived. A low-power 10-bit 200-MS/s CMOS parallel pipeline ADC employing double sampling and a front-end sample-and-hold (S/H) circuit is implemented. Emphasis of the thesis is on high-resolution pipeline ADCs with IF-sampling capability. The resolution is extended beyond the limits set by device matching by using calibration, while time interleaving is applied to widen the signal bandwidth. A review of calibration and error averaging techniques is presented. A simple digital self-calibration technique to compensate capacitor mismatch within a single-channel pipeline ADC, and the gain and offset mismatch between the channels of a time-interleaved ADC, is developed. The new calibration method is validated with two high-resolution BiCMOS prototypes, a 13-bit 50-MS/s single-channel and a 14-bit 160-MS/s parallel pipeline ADC, both utilizing a highly linear front-end allowing sampling from 200-MHz IF-band.reviewe