Advanced High Efficiency and Broadband Power Amplifiers Based on GaN HEMT for Wireless Applications

In advanced wireless communication systems, a rapid increase in the mobile data traffic and broad information bandwidth requirement can lead to the use of complex spectrally efficient modulation schemes such as orthogonal frequency-division multiplexing (OFDM). Generally, complex non-constant envelope modulated signals have very high peak-to-average ratios (PAPR). Doherty Power Amplifier (DPA) is the most commonly used power amplifier (PA) architecture for meeting high efficiency requirement in advanced communication systems, in the presence of high PAPR signals. However, limited bandwidth of the conventional DPA is often identified as a bottleneck for widespread deployment in base-station application for multi-standard communication signals. The research in this thesis focuses on the development of new designs to overcome the bandwidth limitations of a conventional PA. In particular, the bandwidth limitation factors of a conventional DPA architecture are studied. Moreover, a novel design technique is proposed for DPA’s bandwidth extension. In the first PA design, limited bandwidth and linearity problems are addressed simultaneously. For this purpose, a new Class-AB PA with extended bandwidth and improved linearity is presented for LTE 5 W pico-cell base-station over a frequency range of 1.9–2.5 GHz. A two-tone load/source-pull and bias point optimization techniques are used to extract the sweet spots for optimum efficiency and linearity from the 6 W Cree GaN HEMT device for the whole frequency band. The realized prototype presented saturated PAE higher than 60%, a power gain of 13 dB and an average output power of 36.5 dBm over the desired bandwidth. The proposed PA is also characterized by QAM-256 and LTE input communication signals for linearity characterization. Measured ACPRs are lower than -40 dBc for an input power of 17 dBm. The documented results indicate that the proposed Class-AB architecture is suitable for pico-cell base-station application. In the second PA design, an inherent bandwidth limitation of Class-F power amplifier forced by the improper load harmonics terminations at multiple harmonics is investigated and analyzed. It is demonstrated that the impedance tuning of the second and third harmonics at the drain terminal of a transistor is crucial to achieve a broadband performance. The effect of harmonics terminations on power amplifier’s bandwidth up to fourth harmonics is investigated. The implemented broadband Class-F PA achieved maximum saturated drain efficiency 60-77%, and 10 W output power throughout (1.1-2.1 GHz) band. The simulated and measured results verify that the presented Class-F PA is suitable for a high-efficiency system application in wireless communications over a wide range of frequencies. In the third PA design, a single- and dual-input DPA for LTE application in the 3.5 GHz frequency band are presented and compared. The main goal of this study is to improve the performance of gallium–nitride (GaN) Doherty transmitters over a wide bandwidth in the 3.5 GHz frequency band. For this purpose, the linearity-efficiency trade-off for the two proposed architectures is discussed in detail. Simulated results demonstrate that the single- and dual-input DPA exhibited a peak drain efficiency (DE) of 72.4% and 77%, respectively. Both the circuits showed saturated output power more than 42.9 dBm throughout the designed band. Saturated efficiency, gain and bandwidth of dual-input DPA are higher than that of the single-input DPA. On the other side, dual-input DPA linearity is worse as compared to the single-input DPA. In the last PA design, a novel design methodology for ultra-wide band DPA is presented. The bandwidth limitation factors of the conventional Doherty amplifier are discussed on the ground of broadband matching with impedance variation. To extend the DPA bandwidth, three different methods are used such as post-matching, low impedance transformation ratio and the optimization of offset line for wide bandwidth in the proposed design. The proposed Doherty power amplifier was designed and realized based on two 10 W GaN HEMT devices from Cree Inc. The measured results exhibited 42-57% of efficiency at the 6-dB back-off and saturated output power ranges from 41.5 to 43.1 dBm in the frequency range of 1.15 to 2.35 GHz (68.5% fractional bandwidth). Moreover, less than -25 dBc ACPRs are measured at 42 dBm peak output power throughout the designed band. In a nutshell, all power amplifiers presented in this thesis are suitable for wideband operation and their performances are satisfying the required operational standard. Therefore, this thesis has a significant contribution in the domain of high efficiency and broadband power amplifiers

A survey on RF and microwave doherty power amplifier for mobile handset applications

This survey addresses the cutting-edge load modulation microwave and radio frequency power amplifiers for next-generation wireless communication standards. The basic operational principle of the Doherty amplifier and its defective behavior that has been originated by transistor characteristics will be presented. Moreover, advance design architectures for enhancing the Doherty power amplifier’s performance in terms of higher efficiency and wider bandwidth characteristics, as well as the compact design techniques of Doherty amplifier that meets the requirements of legacy 5G handset applications, will be discussed.Agencia Estatal de Investigación | Ref. TEC2017-88242-C3-2-RFundação para a Ciência e a Tecnologia | Ref. UIDP/50008/201

High-Power Microwave/ Radio-Frequency Components, Circuits, and Subsystems for Next-Generation Wireless Radio Front-Ends

As the wireless communication systems evolve toward the future generation, intelligence will be the main signature/trend, well known as the concepts of cognitive and software-defined radios which offer ultimate data transmission speed, spectrum access, and user capacity. During this evolution, the human society may experience another round of `information revolution\u27. However, one of the major bottlenecks of this promotion lies in hardware realization, since all the aforementioned intelligent systems are required to cover a broad frequency range to support multiple communication bands and dissimilar standards. As the essential part of the hardware, power amplifiers (PAs) capable of operating over a wide bandwidth have been identified as the key enabling technology. This dissertation focuses on novel methodologies for designing and realizing broadband high-power PAs, their integration with high-quality-factor (high-Q) tunable filters, and relevant investigations on the reliabilities of these tunable devices. It can be basically divided into three major parts: 1.Broadband High-Efficiency Power Amplifiers. Obtaining high PA efficiency over a wide bandwidth is very challenging, because of the difficulty of performing broadband multi-harmonic matching. However, high efficiency is the critical feature for high-performance PAs due to the ever-increasing demands for environmental friendliness, energy saving, and longer battery life. In this research, novel design methodologies of broad-band highly efficient PAs are proposed, including the first-ever mode-transferring PA theory, novel matching network topology, and wideband reconfigurable PA architecture. These techniques significantly advance the state-of-the-art in terms of bandwidth and efficiency. 2.Co-Design of PAs and High-Q Tunable Filters. When implementing the intelligent communication systems, the conventional approach based on independent RF design philosophy suffers from many inherent defects, since no global optimization is achieved leading to degraded overall performance. An attractive method to solve these difficulties is to co-design critical modules of the transceiver chain. This dissertation presents the first-ever co-design of PAs and tunable filters, in which the redundant inter-module matching is entirely eliminated, leading to minimized size & cost and maximized overall performance. The saved hardware resources can be further transferred to enhance system functionalities. Moreover, we also demonstrate that co-design of PAs and filters can lead to more functionalities/benefits for the wireless systems, e.g. efficient and linear amplification of dual-carrier (or multi-carrier) signals. 3.High-Power/Non-Linear Study on Tunable Devices. High-power limitation/power handling is an everlasting theme of tunable devices, as it determines the operational life and is the threshold for actual industrial applications. Under high-power operation, the high RF voltage can lead to failures like tuners\u27 mechanical deflections and gas discharge in the small air spacing of the cavity. These two mechanisms are studied independently with their instantaneous and long-term effects on the device performance. In addition, an anti-biased topology of electrostatic RF MEMS varactors and tunable filters is proposed and experimentally validated for reducing the non-linear effect induced by bias-noise. These investigations will enlighten the designers on how to avoid and/or minimize the non-ideal effects, eventually leading to longer life cycle and performance sustainability of the tunable devices

A 40-GHz Load Modulated Balanced Power Amplifier using Unequal Power Splitter and Phase Compensation Network in 45-nm SOI CMOS

© 2023 IEEE - All rights reserved. This is the accepted manuscript version of an article which has been published in final form at https://doi.org/10.1109/TCSI.2023.3282731 ​​​​​​​In this work, a ten-way power-combined poweramplifier is designed using a load modulated balanced amplifier(LMBA)-based architecture. To provide the required magnitudeand phase controls between the main and control-signal paths ofthe LMBA, an unequal power splitter and a phase compensationnetwork are proposed. As proof of concept, the designed poweramplifier is implemented in a 45-nm SOI CMOS process. At 40GHz, it delivers a 25.1 dBm Psat with a peak power-addedefficiency (PAE) of 27.9%. At 6-dB power back-off level, itachieves 1.39 times drain efficiency enhancement over an idealClass-B power amplifier. Using a 200-MHz single-carrier 64-QAMsignal, the designed amplifier delivers an average output power of16.5 dBm with a PAE of 13.1% at an EVMrms of -23.9 dB andACPR of -25.3 dBc. The die size, including all testing pads, is only1.92 mm2. To the best of the authors’ knowledge, compared withthe other recently published silicon-based LMBAs, this designachieves the highest Psat.Peer reviewe

Dual-band Power Amplifier for Wireless Communication Base Stations

In wireless communication systems, multiple standards have been implemented to meet the past and present demands of different applications. This proliferation of wireless standards, operating over multiple frequency bands, has increased the demand for radio frequency (RF) components, and consequently power amplifiers (PA) to operate over multiple frequency bands. In this research work, a systematic approach for the synthesis of a novel dual-band matching network is proposed and applied for effective design of PA capable of maintaining high power efficiency at two arbitrary widely spaced frequencies. The proposed dual-band matching network incorporates two different stages. The first one aims at transforming the targeted two complex impedances, at the two operating frequencies, to a real one. The second stage is a dual-band filter that ensures the matching of the former real impedance to the termination impedance to 50 Ohm. Furthermore, an additional transmission line is incorporated between the two previously mentioned stages to adjust the impedances at the second and third harmonics without altering the impedances seen at the fundamental frequencies. Although simple, the harmonic termination control is very effective in enhancing the efficiency of RF transistors, especially when exploiting the Class J design space. The proposed dual-band matching network synthesis methodology was applied to design a dual-band power amplifier using a packaged 45 W gallium nitride (GaN) transistor. The power amplifier prototype maintained a peak power efficiency of about 68% at the two operating frequencies, namely 800 MHz and 1.9 GHz. In addition, a Volterra based digital predistortion technique has been successfully applied to linearize the PA response around the two operating frequencies. In fact, when driven with multi-carrier wideband code division multiple access (WCDMA) and long term evolution (LTE) signals, the linearized amplifier maintained an adjacent channel power ratio (ACPR) of about 50 dBc and 46 dBc, respectively

Class-E Power Amplifiers in Modern RF Transmitters

Power amplifiers have been playing a vital role in most wireless communication systems. In order to improve efficiency of wireless systems, advanced transmitter architectures, such as Doherty amplifiers, outphasing amplifiers, supply voltage modulation techniques are widely used. The goal of this work is to develop novel techniques for building load modulation transmitters based on class-E power amplifiers. The first contribution is an analytical model for derivation load network parameters. The proposed model derives the parameters for both the peak and back-off power levels providing high efficiency. The proposed model demonstrates, that class-E PA with shunt capacitance and shunt filter is capable of providing high drain efficiency for back-off output power levels. The second contribution is a design of a wideband class-E power amplifier (PA) with shunt capacitance and shunt filter. The broadband operation has been achieved by application of the double reactance compensation technique. Simulated and experimental results are presented. The performance of the fabricated PA is compared with existing wideband PAs. The third contribution is application of the proposed technique to outphasing PA design. The designed outphasing PA was optimized, fabricated and tested. A possibility to extend the operational bandwidth of the PA is considered. Also the application of the proposed technique to Doherty PA design is demonstrated. The fourth contribution is linearization of outphasing PA. Firstly, an analytical model describing the nonlinearity of nonisolated combiners under amplitude imbalance is presented. Secondly, a novel phase-only predistortion technique for class-E outphasing PAs is proposed. Thirdly, linearization of the fabricated outphasing PA based on memory polynomial model is demonstrated using a 64QAM OFDM modulated signal with 20 MHz bandwidth. Overall, this work provides novel techniques for load modulation transmitter design based on class-E power amplifiers with shunt capacitance and shunt filter

Novel design & implementation of a broadband and highly efficient doherty power amplifier

Master'sMASTER OF ENGINEERIN