Analog radio over fiber solutions for multi-band 5g systems

This study presents radio over fiber (RoF) solutions for the fifth-generation (5G) of wireless networks. After the state of the art and a technical background review, four main contributions are reported. The first one is proposing and investigating a RoF technique based on a dual-drive Mach-Zehnder modulator (DD-MZM) for multi-band mobile fronthauls, in which two radiofrequency (RF) signals in the predicted 5G bands individually feed an arm of the optical modulator. Experimental results demonstrate the approach enhances the RF interference mitigation and can prevail over traditional methods. The second contribution comprises the integration of a 5G transceiver, previously developed by our group, in a passive optical network (PON) using RoF technology and wavelength division multiplexing (WDM) overlay. The proposed architecture innovates by employing DD-MZM and enables to simultaneously transport baseband and 5G candidate RF signals in the same PON infrastructure. The proof-of-concept includes the transmission of a generalized frequency division multiplexing (GFDM) signal generated by the 5G transceiver in the 700 MHz band, a 26 GHz digitally modulated signal as a millimeter-waves 5G band, and a baseband signal from an gigabit PON (GPON). Experimental results demonstrate the 5G transceiver digital performance when using RoF technology for distributing the GFDM signal, as well as Gbit/s throughput at 26 GHz. The third contribution is the implementation of a flexible-waveform and multi-application fiber-wireless (FiWi) system toward 5G. Such system includes the FiWi transmission of the GFDM and filtered orthogonal frequency division multiplexing (F-OFDM) signals at 788 MHz, toward long-range cells for remote or rural mobile access, as well as the recently launched 5G NR standard in microwave and mm-waves, aiming enhanced mobile broadband indoor and outdoor applications. Digital signal processing (DSP) is used for selecting the waveform and linearizing the RoF link. Experimental results demonstrate the suitability of the proposed solution to address 5G scenarios and requirements, besides the applicability of using existent fiber-to-the-home (FTTH) networks from Internet service providers for implementing 5G systems. Finally, the fourth contribution is the implementation of a multi-band 5G NR system with photonic-assisted RF amplification (PAA). The approach takes advantage of a novel PAA technique, based on RoF technology and four-wave mixing effect, that allows straightforward integration to the transport networks. Experimental results demonstrate iv uniform and stable 15 dB wideband gain for Long Term Evolution (LTE) and three 5G signals, distributed in the frequency range from 780 MHz to 26 GHz and coexisting in the mobile fronthaul. The obtained digital performance has efficiently met the Third-Generation Partnership Project (3GPP) requirements, demonstrating the applicability of the proposed approach for using fiber-optic links to distribute and jointly amplify LTE and 5G signals in the optical domain.Agência 1Este trabalho apresenta soluções de rádio sobre fibra (RoF) para aplicações em redes sem fio de quinta geração (5G), e inclui quatro contribuições principais. A primeira delas refere-se à proposta e investigação de uma técnica de RoF baseada no modulador eletroóptico de braço duplo, dual-drive Mach-Zehnder (DD-MZM), para a transmissão simultânea de sinais de radiofrequência (RF) em bandas previstas para redes 5G. Resultados experimentais demonstram que o uso do DD-MZM favorece a ausência de interferência entre os sinais de RF transmitidos. A segunda contribuição trata da integração de um transceptor de RF, desenvolvido para aplicações 5G e apto a prover a forma de onda conhecida como generalized frequency division multiplexing (GFDM), em uma rede óptica passiva (PON) ao utilizar RoF e multiplexação por divisão de comprimento de onda (WDM). A arquitetura proposta permite transportar, na mesma infraestrutura de rede, sinais em banda base e de radiofrequência nas faixas do espectro candidatas para 5G. A prova de conceito inclui a distribuição conjunta de três tipos de sinais: um sinal GFDM na banda de 700 MHz, proveniente do transceptor desenvolvido; um sinal digital na frequência de 26 GHz, assumindo a faixa de ondas milimétricas; sinais em banda base provenientes de uma PON dedicada ao serviço de Internet. Resultados experimentais demonstram o desempenho do transceptor de RF ao utilizar a referida arquitetura para distribuir sinais GFDM, além de taxas de transmissão de dados da ordem de Gbit/s na faixa de 26 GHz. A terceira contribuição corresponde à implementação de um sistema fibra/rádio potencial para redes 5G, operando inclusive com o padrão ―5G New Radio (5G NR)‖ nas faixas de micro-ondas e ondas milimétricas. Tal sistema é capaz de prover macro células na banda de 700 MHz para aplicações de longo alcance e/ou rurais, utilizando sinais GFDM ou filtered orthogonal frequency division multiplexing (F-OFDM), assim como femto células na banda de 26 GHz, destinada a altas taxas de transmissão de dados para comunicações de curto alcance. Resultados experimentais demonstram a aplicabilidade da solução proposta para redes 5G, além da viabilidade de utilizar redes ópticas pertencentes a provedores de Internet para favorecer sistemas de nova geração. Por fim, a quarta contribuição trata da implementação de um sistema 5G NR multibanda, assistido por amplificação de RF no domínio óptico. Esse sistema faz uso de um novo método de amplificação, baseado no efeito não linear da mistura de quatro ondas, que vi permite integração direta em redes de transporte envolvendo rádio sobre fibra. Resultados experimentais demonstram ganho de RF igual a 15 dB em uma ampla faixa de frequências (700 MHz até 26 GHz), atendendo simultaneamente tecnologias de quarta e quinta geração. O desempenho digital obtido atendeu aos requisitos estabelecidos pela 3GPP (Third-Generation Partnership Project), indicando a aplicabilidade da solução em questão para distribuir e conjuntamente amplificar sinais de RF em enlaces de fibra óptica

Class-E Power Amplifiers in Modern RF Transmitters

Power amplifiers have been playing a vital role in most wireless communication systems. In order to improve efficiency of wireless systems, advanced transmitter architectures, such as Doherty amplifiers, outphasing amplifiers, supply voltage modulation techniques are widely used. The goal of this work is to develop novel techniques for building load modulation transmitters based on class-E power amplifiers. The first contribution is an analytical model for derivation load network parameters. The proposed model derives the parameters for both the peak and back-off power levels providing high efficiency. The proposed model demonstrates, that class-E PA with shunt capacitance and shunt filter is capable of providing high drain efficiency for back-off output power levels. The second contribution is a design of a wideband class-E power amplifier (PA) with shunt capacitance and shunt filter. The broadband operation has been achieved by application of the double reactance compensation technique. Simulated and experimental results are presented. The performance of the fabricated PA is compared with existing wideband PAs. The third contribution is application of the proposed technique to outphasing PA design. The designed outphasing PA was optimized, fabricated and tested. A possibility to extend the operational bandwidth of the PA is considered. Also the application of the proposed technique to Doherty PA design is demonstrated. The fourth contribution is linearization of outphasing PA. Firstly, an analytical model describing the nonlinearity of nonisolated combiners under amplitude imbalance is presented. Secondly, a novel phase-only predistortion technique for class-E outphasing PAs is proposed. Thirdly, linearization of the fabricated outphasing PA based on memory polynomial model is demonstrated using a 64QAM OFDM modulated signal with 20 MHz bandwidth. Overall, this work provides novel techniques for load modulation transmitter design based on class-E power amplifiers with shunt capacitance and shunt filter

Joint compensation of I/Q impairments and PA nonlinearity in mobile broadband wireless transmitters

The main focus of this thesis is to develop and investigate a new possible solution for compensation of in-phase/quadrature-phase (I/Q) impairments and power amplifier (PA) nonlinearity in wireless transmitters using accurate, low complexity digital predistortion (DPD) technique. After analysing the distortion created by I/Q modulators and PAs together with nonlinear crosstalk effects in multi-branch multiple input multiple output (MIMO) wireless transmitters, a novel two-box model is proposed for eliminating those effects. The model is realised by implementing two phases which provide an optimisation of the identification of any system. Another improvement is the capability of higher performance of the system without increasing the computational complexity. Compared with conventional and recently proposed models, the approach developed in this thesis shows promising results in the linearisation of wireless transmitters. Furthermore, the two-box model is extended for concurrent dual-band wireless transmitters and it takes into account cross-modulation (CM) products. Besides, it uses independent processing blocks for both frequency bands and reduces the sampling rate requirements of converters (digital-to-analogue and analogue-to-digital). By using two phases for the implementation, the model enables a scaling down of the nonlinear order and the memory depth of the applied mathematical functions. This leads to a reduced computational complexity in comparison with recently developed models. The thesis provides experimental verification of the two-box model for multi-branch MIMO and concurrent dual-band wireless transmitters. Accordingly, the results ensure both the compensation of distortion and the performance evaluation of modern broadband wireless transmitters in terms of accuracy and complexity

Broadband Linearity-Enhanced Doherty Power Amplifier Design Techniques for 5G Sub-6 GHz Applications

The recently deployed fifth generation (5G) cellular networks represent a significant technological advancement over fourth generation (4G) networks. Specifically, new 5G frequency bands were allocated at sub-6 GHz and instantaneous signal bandwidths were increased to satisfy the rapidly growing needs for increased data rates. Furthermore, 5G uses more complex modulation schemes to improve spectrum efficiency. Finally, 5G introduced massive multiple input multiple output (MIMO), where multiple transceivers are used to direct the signal towards specific users, increasing channel capacity. Conventional power amplifiers (PAs) are not suitable for 5G applications due to the increased signal and system complexity. For example, the Doherty power amplifier (DPA) technique is popular since DPAs can efficiently amplify signals with complex modulation schemes, but conventional DPAs have narrow bandwidth and poor linearity that preclude their use in 5G systems. This motivated research into DPA bandwidth and linearity improvements for use in 5G networks. This work focuses on bandwidth and linearity enhancement for sub-6 GHz DPAs realized using discrete components on a printed circuit board (PCB). Bandwidth is improved using broadband architectures for the DPA output combiner network (OCN), the absorption of drain parasitics, and broadband input matching network (IMN) design. Linearity is enhanced by proper drain biasing network design, and careful selection of transistor source impedances. A 3.3–5.0 GHz DPA using these techniques is designed and fabricated. Under wideband modulated signal excitation, the DPA offers very good linearity with appropriate digital predistortion (DPD). A 2×2 array of DPAs is evaluated in fully digital MIMO setup using a 2×2 antenna array. The DPA array achieves excellent linearity characteristics under 100 MHz signals and use of dual-input single-output (DISO) DPD. The DPA remains the ideal choice in 5G MIMO systems when compared to the class AB PA since it can maintain a higher average drain efficiency and similar linearity

Low Complexity DPD for Multi-Band Radio over Fiber Transmission Systems

The increasing demand for broadband wireless transmission in the modern internet has led to the proposal and standardization of the fifth-generation (5G) mobile communication system, which offers massive device connectivity, high bit rates, low latency, and cost sustainability. However, maintaining a high transmission rate as well as low latency is difficult to achieve simultaneously, which requires some state-of-art fronthaul transmission techniques. Therefore, radio over fiber (RoF) with different approaches like digital RoF (D-RoF), analog RoF (A-RoF), and delta-sigma modulation based RoF (DSM-RoF) for 5G fronthaul transmission has been introduced. Those RoF techniques may significantly reduce complexity and power consumption at base stations, but the extra electric to optic (E/O), optic to electric (O/E) converters and power amplifiers could introduce extra nonlinearity into the system. Moreover, ultra-broadband or multi-band ultra-broadband signal is introduced in 5G to further increase the transmission rate, which further increases the impact of the nonlinearity. Therefore, broadband linearization techniques are necessary for RoF fronthaul transmission systems due to the fragile of the signal and the inherent nonlinear distortions introduced by RoF link. To reduce the degradation of nonlinearity for RoF link, digital predistortion (DPD) techniques have been extensively researched to address these challenges. In a multi-band or multi-dimensional RoF system, multi-band DPD is required. Multi-dimensional DPD should be able to suppress the internal distortion within each band/dimension but also inter-distortion between different bands/dimensions. Unfortunately, the dimension higher than 3 causes a high calculation complexity to get the DPD function coefficients. There have been lots of efforts that have been made to obtain less-complexity DPD with better accuracy for multi-band or multidimensional signals. However, very limited DPD techniques have been proposed in simplifying the fundamental linearization function for bands exceeding four. Thus, the multi-band/multidimensional DPD has not been really got in used in commercial products because of the high complexity, high cost and high-power consumption. Thus, a simplified linearization approach for multi-band DPD is still needed. In this thesis, a new low-complexity multidimensional DPD is introduced. This proposed DPD introduces a simplified DPD function, which evolves from the conventional memory polynomial function. Compared with the conventional multi-dimensional DPD, this proposed approach has lower complexity increased with the increase of signal bands or dimensions, nonlinearity orders, and memory effect depth. For example, the conventional DPD function needs a total of 40040 coefficients for the 6-band signals with a nonlinearity order of 10 and a memory depth of 5. However, this proposed low-complexity DPD function needs 640 coefficients. A substantial reduction in complexity is clearly observed. The performance of the proposed DPD is evaluated by both simulation and experiments. An up to 6-band 64-QAM orthogonal frequency division multiplexing (OFDM) signal with each band of 200 MHz in simulations and an up to 5-band 20 MHz 64-QAM OFDM signal in experiments are used. The performance is evaluated in the means of error vector magnitude (EVM) of the received signal. The average improvement of EVM in simulation for 3-band, 4-band, 5-band and 6-band signals is 19.97 dB, 18.65 dB, 16.64 dB and 15.44 dB, respectively. The average improvement of EVM in experiments for 4-band and 5-band signals is 5.67 dB and 8.1 dB, respectively. The above results prove that the proposed DPD can significantly reduce the complexity and provide good linearization

Experimental Demonstration and Performance Enhancement of 5G NR Multiband Radio over Fiber System Using Optimized Digital Predistortion

This paper presents an experimental realization of multiband 5G new radio (NR) optical front haul (OFH) based radio over fiber (RoF) system using digital predistortion (DPD). A novel magnitude-selective affine (MSA) based DPD method is proposed for the complexity reduction and performance enhancement of RoF link followed by its comparison with the canonical piece wise linearization (CPWL), decomposed vector rotation method (DVR) and generalized memory polynomial (GMP) methods. Similarly, a detailed study is shown followed by the implementation proposal of novel neural network (NN) for DPD followed by its comparison with MSA, CPWL, DVR and GMP methods. In the experimental testbed, 5G NR standard at 20 GHz with 50 MHz bandwidth and flexible-waveform signal at 3 GHz with 20 MHz bandwidth is used to cover enhanced mobile broad band and small cells scenarios. A dual drive Mach Zehnder Modulator having two distinct radio frequency signals modulates a 1310 nm optical carrier using distributed feedback laser for 22 km of standard single mode fiber. The experimental results are presented in terms of adjacent channel power ratio (ACPR), error vector magnitude (EVM), number of estimated coefficients and multiplications. The study aims to identify those novel methods such as MSA DPD are a good candidate to deploy in real time scenarios for DPD in comparison to NN based DPD which have a slightly better performance as compared to the proposed MSA method but has a higher complexity levels. Both, proposed methods, MSA and NN are meeting the 3GPP Release 17 requirements

Integrated Filters and Couplers for Next Generation Wireless Tranceivers

The main focus of this thesis is to investigate the critical nonlinear distortion issues affecting RF/Microwave components such as power amplifiers (PA) and develop new and improved solutions that will improve efficiency and linearity of next generation RF/Microwave mobile wireless communication systems. This research involves evaluating the nonlinear distortions in PA for different analog and digital signals which have been a major concern. The second harmonic injection technique is explored and used to effectively suppress nonlinear distortions. This method consists of simultaneously feeding back the second harmonics at the output of the power amplifier (PA) into the input of the PA. Simulated and measured results show improved linearity results. However, for increasing frequency bandwidth, the suppression abilities reduced which is a limitation for 4G LTE and 5G networks that require larger bandwidth (above 5 MHz). This thesis explores creative ways to deal with this major drawback. The injection technique was modified with the aid of a well-designed band-stop filter. The compact narrowband notch filter designed was able to suppress nonlinear distortions very effectively when used before the PA. The notch filter is also integrated in the injection technique for LTE carrier aggregation (CA) with multiple carriers and significant improvement in nonlinear distortion performance was observed. This thesis also considers maximizing efficiency alongside with improved linearity performance. To improve on the efficiency performance of the PA, the balanced PA configuration was investigated. However, another major challenge was that the couplers used in this configuration are very large in size at the desired operating frequency. In this thesis, this problem was solved by designing a compact branch line coupler. The novel coupler was simulated, fabricated and measured with performance comparable to its conventional equivalent and the coupler achieved substantial size reduction over others. The coupler is implemented in the balanced PA configuration giving improved input and output matching abilities. The proposed balanced PA is also implemented in 4G LTE and 5G wireless transmitters. This thesis provides simulation and measured results for all balanced PA cases with substantial efficiency and linearity improvements observed even for higher bandwidths (above 5 MHz). Additionally, the coupler is successfully integrated with rectifiers for improved energy harvesting performance and gave improved RF-dc conversion efficienc

Novel Predistortion System for 4G/5G Small-Cell and Wideband Transmitters

To meet the growing demand for mobile data, various technologies are being introduced to wireless networks to increase system capacity. On one hand, large number of small-cell base stations are adopted to serve the reduced cell size; on the other hand, millimeter wave (mm-wave) systems with large antenna arrays that transmit ultra-wideband signals are expected in fifth generation (5G) networks. Power amplifiers (PAs), responsible for boosting the radio frequency (RF) signal power, are the most critical components in base station transmitters, and dominate the overall efficiency and linearity of the system. The design challenges to balance the contradictory requirements of efficiency and linearity of the PAs are usually addressed by linearization techniques, particularly the digital predistortion (DPD) system. However, existing DPD solutions face increasing difficulties keeping up with new developments in base station technologies. When considering sub-6 GHz small-cell base station transmitters, analog and RF predistortion techniques have recently received renewed attention due to their inherent low power nature. Their achievable linearization capacity is significantly limited, however, largely by their implementation complexity in realizing the needed predistortion models in analog circuitry. On the other hand, despite significant developments in DPD models for wideband signals, the implementations of such DPD models in practical hardware have received relatively little attention. Yet the conventional implementation of a DPD engine is limited by the maximum clock frequency of the digital circuitry employed and cannot be scaled to satisfy the growing bandwidth of transmitted signals for 5G networks. Furthermore, both analog and digital solutions require a transmitter-observation-receiver (TOR) to capture the PA outputs, necessitates the use of analog-to-digital converters (ADCs) whose complexity and power consumption increase with signal bandwidth. Such trend is not scalable for future base stations, and new innovations in feedback and training methods are required. This thesis presents a number of contributions to address the above identified challenges. To reduce the power overhead of the linearization system, a digitally-assisted analog-RF predistortion (DA-ARFPD) system that uses a novel predistortion model is introduced. The proposed finite-impulse-response assisted envelope memory polynomial (FIR-EMP) model allows for a reduction of hardware implementation complexity while maintaining good linearization capacity and low power overhead. A two-step small-signal-assisted parameter identification (SSAPI) algorithm is devised to estimate the parameters of the two main blocks of the FIR-EMP model, such that the training can be completed efficiently. A DA-ARFPD test bench has been built, which incorporates major RF components, to assess the validity of the proposed FIR-EMP scheme and the SSAPI algorithm. Measurement results show that the proposed FIR-EMP model with SSAPI algorithm can successfully linearize multiple PAs driven with various wideband and carrier-aggregated signals of up to 80~MHz modulation bandwidths for sub-6 GHz systems. Next, a hardware-efficient real-time DPD system with scalable linearization bandwidth for ultra-wideband 5G mm-wave transmitters is proposed. It uses a novel parallel-processing DPD engine architecture to process multiple samples per clock cycle, overcomes the linearization bandwidth limit imposed by the maximum clock rate of digital circuits used in conventional DPD implementation. Potentially unlimited linearization bandwidth could be achieved by using the proposed system with current digital circuit technologies. The linearization performance and bandwidth scalability of the proposed system is demonstrated experimentally using a silicon-based Doherty (DPA) with 400 MHz wideband signal operating at 28 GHz, and over-the-air measurements using a 64-element beamforming array with 800 MHz wideband signal, also at 28 GHz. The proposed DPD system achieves over 2.4 GHz linearization bandwidth using only a 300 MHz core clock for the digital circuits. Finally, to reduce the power consumption and cost of the TOR, a new approach to train the predistorter using under-sampled feedback signal is presented. Using aliased samples of the PA's output captured at either baseband or intermedia frequency (IF), the proposed algorithm is able to compute the coefficients of the predistortion engine to linearize the PA using a direct learning architecture. Experimentally, both the baseband and IF schemes achieve linearization performance comparable to a full-rate system. Implemented together with a parallel-processing based DPD engine on a field-programmable gate array (FPGA) based system-on-chip (SOC), the proposed feedback and training solution achieves over 2.4~GHz linearization bandwidth using an ADC operating at a clock rate of 200 MHz. Its performance is demonstrated experimentally by linearizing a silicon DPA with 200 MHz and 400 MHz signals in conductive measurements, and a 64-element beamforming array with 400 MHz and 800 MHz signals in over-the-air testing

Optimizing multi-antenna M-MIMO DM communication systems with advanced linearization techniques for RF front-end nonlinearity compensation in a comprehensive design and performance evaluation study

The study presented in this research focuses on linearization strategies for compensating for nonlinearity in RF front ends in multi-antenna M-MIMO OFDM communication systems. The study includes the design and evaluation of techniques such as analogue pre-distortion (APD), crest factor reduction (CFR), multi-antenna clipping noise cancellation (M-CNC), and multi-clipping noise cancellation (MCNC). Nonlinearities in RF front ends can cause signal distortion, leading to reduced system performance. To address this issue, various linearization methods have been proposed. This research examines the impact of antenna correlation on power amplifier efficiency and bit error rate (BER) of transmissions using these methods. Simulation studies conducted under high signal-to-noise ratio (SNR) regimes reveal that M-CNC and MCNC approaches offer significant improvement in BER performance and PA efficiency compared to other techniques. Additionally, the study explores the influence of clipping level and antenna correlation on the effectiveness of these methods. The findings suggest that appropriate linearization strategies should be selected based on factors such as the number of antennas, SNR, and clipping level of the system