Automatic test pattern generation for asynchronous circuits

The testability of integrated circuits becomes worse with transistor dimensions reaching nanometer scales. Testing, the process of ensuring that circuits are fabricated without defects, becomes inevitably part of the design process; a technique called design for test (DFT). Asynchronous circuits have a number of desirable properties making them suitable for the challenges posed by modern technologies, but are severely limited by the unavailability of EDA tools for DFT and automatic test-pattern generation (ATPG). This thesis is motivated towards developing test generation methodologies for asynchronous circuits. In total four methods were developed which are aimed at two different fault models: stuck-at faults at the basic logic gate level and transistor-level faults. The methods were evaluated using a set of benchmark circuits and compared favorably to previously published work. First, ABALLAST is a partial-scan DFT method adapting the well-known BALLAST technique for asynchronous circuits where balanced structures are used to guide the selection of the state-holding elements that will be scanned. The test inputs are automatically provided by a novel test pattern generator, which uses time frame unrolling to deal with the remaining, non-scanned sequential C-elements. The second method, called AGLOB, uses algorithms from strongly-connected components in graph graph theory as a method for finding the optimal position of breaking the loops in the asynchronous circuit and adding scan registers. The corresponding ATPG method converts cyclic circuits into acyclic for which standard tools can provide test patterns. These patterns are then automatically converted for use in the original cyclic circuits. The third method, ASCP, employs a new cycle enumeration method to find the loops present in a circuit. Enumerated cycles are then processed using an efficient set covering heuristic to select the scan elements for the circuit to be tested.Applying these methods to the benchmark circuits shows an improvement in fault coverage compared to previous work, which, for some circuits, was substantial. As no single method consistently outperforms the others in all benchmarks, they are all valuable as a designer’s suite of tools for testing. Moreover, since they are all scan-based, they are compatible and thus can be simultaneously used in different parts of a larger circuit. In the final method, ATRANTE, the main motivation of developing ATPG is supplemented by transistor level test generation. It is developed for asynchronous circuits designed using a State Transition Graph (STG) as their specification. The transistor-level circuit faults are efficiently mapped onto faults that modify the original STG. For each potential STG fault, the ATPG tool provides a sequence of test vectors that expose the difference in behavior to the output ports. The fault coverage obtained was 52-72 % higher than the coverage obtained using the gate level tests. Overall, four different design for test (DFT) methods for automatic test pattern generation (ATPG) for asynchronous circuits at both gate and transistor level were introduced in this thesis. A circuit extraction method for representing the asynchronous circuits at a higher level of abstraction was also implemented. Developing new methods for the test generation of asynchronous circuits in this thesis facilitates the test generation for asynchronous designs using the CAD tools available for testing the synchronous designs. Lessons learned and the research questions raised due to this work will impact the future work to probe the possibilities of developing robust CAD tools for testing the future asynchronous designs

Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review

The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER

Testing micropipelines

Journal ArticleMicropipelines, self-timed event-driven pipelines, are an attractive way of structuring asynchronous systems that exhibit many of the advantages of general asynchronous systems, but enough structure to make the design of significant systems practical. As with any design method, testing is critical. We present a technique for testing self-timed micropipelines for stuck-at faults and for delay faults an the bundled data paths by modifying the latch and control elements to include a built-in scan path for testing. This scan path allows the processing logic in the micropipeline, to be fully tested with only a small overhead in the latch and control circuits. The test method is very similar to scan testing in synchronous systems, but the micropipeline retains its self-timed behavior during normal operation

Doctor of Philosophy

dissertationThe design of integrated circuit (IC) requires an exhaustive verification and a thorough test mechanism to ensure the functionality and robustness of the circuit. This dissertation employs the theory of relative timing that has the advantage of enabling designers to create designs that have significant power and performance over traditional clocked designs. Research has been carried out to enable the relative timing approach to be supported by commercial electronic design automation (EDA) tools. This allows asynchronous and sequential designs to be designed using commercial cad tools. However, two very significant holes in the flow exist: the lack of support for timing verification and manufacturing test. Relative timing (RT) utilizes circuit delay to enforce and measure event sequencing on circuit design. Asynchronous circuits can optimize power-performance product by adjusting the circuit timing. A thorough analysis on the timing characteristic of each and every timing path is required to ensure the robustness and correctness of RT designs. All timing paths have to conform to the circuit timing constraints. This dissertation addresses back-end design robustness by validating full cyclical path timing verification with static timing analysis and implementing design for testability (DFT). Circuit reliability and correctness are necessary aspects for the technology to become commercially ready. In this study, scan-chain, a commercial DFT implementation, is applied to burst-mode RT designs. In addition, a novel testing approach is developed along with scan-chain to over achieve 90% fault coverage on two fault models: stuck-at fault model and delay fault model. This work evaluates the cost of DFT and its coverage trade-off then determines the best implementation. Designs such as a 64-point fast Fourier transform (FFT) design, an I2C design, and a mixed-signal design are built to demonstrate power, area, performance advantages of the relative timing methodology and are used as a platform for developing the backend robustness. Results are verified by performing post-silicon timing validation and test. This work strengthens overall relative timed circuit flow, reliability, and testability

Testing of Asynchronous NULL Conventional Logic (NCL) Circuits

Due to the absence of a global clock and presence of more state holding elements that synchronize the control and data paths, conventional automatic test pattern generation (ATPG) algorithms would fail when applied to asynchronous circuits, leading to poor fault coverage. This paper focuses on design for test (DFT) techniques aimed at making asynchronous NCL designs testable using existing DFT CAD tools with reasonable gate overhead, by enhancing controllability of feedback nets and observability for fault sites that are flagged unobservable. The proposed approach performs scan and test points insertion on NCL designs using custom ATPG library. The approach has been automated, which is essential for large systems; and are fully compatible with industry standard tools

DFT Techniques and Automation for Asynchronous NULL Conventional Logic Circuits

Conventional automatic test pattern generation (ATPG) algorithms fail when applied to asynchronous NULL convention logic (NCL) circuits due to the absence of a global clock and presence of more state-holding elements, leading to poor fault coverage. This paper presents a design-for-test (DFT) approach aimed at making asynchronous NCL designs testable using conventional ATPG programs. We propose an automatic DFT insertion flow (ADIF) methodology that performs scan and test point insertion on NCL designs to improve test coverage, using a custom ATPG library. Experimental results show significant increase in fault coverage for NCL cyclic and acyclic pipelined designs

Doctor of Philosophy

dissertationAsynchronous design has a very promising potential even though it has largely received a cold reception from industry. Part of this reluctance has been due to the necessity of custom design languages and computer aided design (CAD) flows to design, optimize, and validate asynchronous modules and systems. Next generation asynchronous flows should support modern programming languages (e.g., Verilog) and application specific integrated circuits (ASIC) CAD tools. They also have to support multifrequency designs with mixed synchronous (clocked) and asynchronous (unclocked) designs. This work presents a novel relative timing (RT) based methodology for generating multifrequency designs using synchronous CAD tools and flows. Synchronous CAD tools must be constrained for them to work with asynchronous circuits. Identification of these constraints and characterization flow to automatically derive the constraints is presented. The effect of the constraints on the designs and the way they are handled by the synchronous CAD tools are analyzed and reported in this work. The automation of the generation of asynchronous design templates and also the constraint generation is an important problem. Algorithms for automation of reset addition to asynchronous circuits and power and/or performance optimizations applied to the circuits using logical effort are explored thus filling an important hole in the automation flow. Constraints representing cyclic asynchronous circuits as directed acyclic graphs (DAGs) to the CAD tools is necessary for applying synchronous CAD optimizations like sizing, path delay optimizations and also using static timing analysis (STA) on these circuits. A thorough investigation for the requirements of cycle cutting while preserving timing paths is presented with an algorithm to automate the process of generating them. A large set of designs for 4 phase handshake protocol circuit implementations with early and late data validity are characterized for area, power and performance. Benchmark circuits with automated scripts to generate various configurations for better understanding of the designs are proposed and analyzed. Extension to the methodology like addition of scan insertion using automatic test pattern generation (ATPG) tools to add testability of datapath in bundled data asynchronous circuit implementations and timing closure approaches are also described. Energy, area, and performance of purely asynchronous circuits and circuits with mixed synchronous and asynchronous blocks are explored. Results indicate the benefits that can be derived by generating circuits with asynchronous components using this methodology