Characterization of Single- and Multi-antenna Wireless Channels

The wireless propagation channel significantly influences the received signal, so that it needs to be modeled effectively. Extensive measurements and analysis are required for investigating the validity of theoretical models and postulating new models based on measurements. Such measurements, analysis, and modeling are the topic of this thesis. The focus of the included contributions are Multiple-Input Multiple-Output (MIMO) propagation channels and radio channels for sensor network applications. Paper I presents results from one of the first MIMO measurements for a double-directional characterization of the outdoor-to-indoor wireless propagation channel. Such channels are of interest for both cellular and wireless LAN applications. We discuss physical aspects of building penetration, and also provide statistics of angle and delay spreads in the channel. The paper also investigates the coupling between DOD and DOA and the two spectra are found to have non-negligible dependence. We test the applicability of three analytical channel models that make different assumptions on the coupling between DODs and DOAs. Our results indicate that analytical models, that impose fewer restrictions on the DOD to DOA coupling, should be used preferrably over models such as the Kronecker model that have more restrictive assumptions. Paper II presents a cluster-based analysis of the outdoor-to-indoor MIMO measurements analyzed in Paper I. A subset of parameters of the COST 273 channel model, a generic model for MIMO propagation channels, are characterized for the outdoor-to-indoor scenario. MPC parameters are extracted at each measured location using a high-resolution algorithm and clusters of MPCs are identified with an automated clustering approach. In particular, the adopted clustering approach requires that all MPC parameters must be similar in order for the MPCs to form a cluster. A statistical analysis of the identified clusters is performed for both the intra- and inter-cluster properties. Paper III analyzes the spatial fading distribution for a range of canonical sensor deployment scenarios. The presented results are relevant to communicating within, and between, clusters of nodes. Contrary to the widely accepted assumption in published literature that the channel is AWGN at a small-enough distance, our measurements indicate that values of the Rice factor do not, in general, increase monotonically as the Tx-Rx distance is reduced. A probability mixture model is presented, with distance dependent parameters, to account for the distance dependent variations of the Rice factor. A simulation model that includes small- and large-scale fading effects is presented. According to the modeling approach, a sensor node placed anywhere within the spatial extent of a small-scale region will experience the channel statistics applicable to that region. Paper IV presents results characterizing a radio channel for outdoor short-range sensor networks. A number of antennas are placed on the ground in an open area and time-variation of the channel is induced by a person moving in the vicinity of the nodes. The channel statistics of both the LOS path and the overall narrowband signal are non-stationary. We investigate the stationarity interval length to be used for small-scale analysis. Our analysis of the various measured links shows that the Rx signal strength is significantly influenced by a moving person only when the person blocks the LOS path. We present a generic approach for modeling the LOS blockage, and also model the time-variant Doppler spectrum of the channel's scattered components

Analytical dual-link MIMO channel model using correlated correlation matrices

Analytical Multiple-Input Multiple-Output (MIMO) models are often attractive due to their low complexity when analyzing possibilities and limitations in the system. In this paper we outline a a possible dual link extension of an analytical MIMO channel model and investigate its suitability based on measurements of a dual link MIMO scenario. The extension is based on the correlation matrix distance (CMD) as a gauge to generate correlation matrices for the additional links of the multi-link scenario

Analysis of MIMO Communications Systems Based on Experimentally Observed Channels

This thesis presents an analysis of multiple-input/multiple-output (MIMO) communications systems where the objective is to provide a unified solution to the problems of (i) crosstalk coupling in transmission line channels (ii) multi-path fading in the time variant high frequency wireless channel. In the case of transmission line channels, a comparative analysis is presented of the performance of MIMO communications systems based on balanced CAT 5 twisted-pair transmission lines, balanced twisted-pair telephone transmission lines scheme as well as unbalanced flat-pair transmission lines. The unbalanced flat-pair transmission lines are viewed as a model for digital subscriber lines (DSLs) which may be deemed out-of-range for high speed internet connections because of the circumstances of poor balance, high insertion losses and high degrees of crosstalk. This comparative analysis is then extended to examine effect of imperfect knowledge of the transmission line channels on MIMO communications system performance. In the case of wireless channels, an analysis is presented which investigates the effect of both the Rayleigh and Ricean channels on MIMO communications system performance. Again the analysis of the wireless channels is extended to examine the effect of imperfect knowledge of the channel on MIMO communications systems performance. All of the analyses in this work are based on experimentally observed channels. In the case of the transmission line channels, it is concluded that MIMO communications systems do offer the possibility of high speed internet connectivity on transmission lines that, hereto, would have been considered out-of-range for such services. Considering the CAT 5 transmission line channels, it is concluded that the MIMO communications system provide enhancement at frequencies above 50 MHz and therefore the possibly of extending length and coverage above the standard 100 metres is proposed. On the other hand, the improved performance of the twisted-pair telephone transmission lines is consistent over the range from 300 kHz to 100 MHz when the MIMO system is applied. For all the transmission line channels that are examined, the extent of imperfect knowledge of the channel that can be allowed while maintaining a reasonable MIMO communications system performance is indicated. In the case of the wireless channels, it is concluded that MIMO communications system performance is better in the case of Rayleigh channel than in the case of Ricean channel provided that the degree of correlation of the multi-path channel impulse response components is equivalent. Also, as the number of transmitters and receivers, N T, increases the effect of a given degree of imperfect knowledge of the wireless channel becomes more detrimental on MIMO communication system performance. This work thus indicates the extent of imperfect knowledge of the wireless channel that can be allowed while maintaining a reasonable MIMO communications system performance. The trade-off between increased capacity gain and decreased accuracy of knowledge of the channel as the dimension, N T, was increased is highlighted

Information-theoretic analysis of MIMO channel sounding

The large majority of commercially available multiple-input multiple-output (MIMO) radio channel measurement devices (sounders) is based on time-division multiplexed switching (TDMS) of a single transmit/receive radio-frequency chain into the elements of a transmit/receive antenna array. While being cost-effective, such a solution can cause significant measurement errors due to phase noise and frequency offset in the local oscillators. In this paper, we systematically analyze the resulting errors and show that, in practice, overestimation of channel capacity by several hundred percent can occur. Overestimation is caused by phase noise (and to a lesser extent frequency offset) leading to an increase of the MIMO channel rank. Our analysis furthermore reveals that the impact of phase errors is, in general, most pronounced if the physical channel has low rank (typical for line-of-sight or poor scattering scenarios). The extreme case of a rank-1 physical channel is analyzed in detail. Finally, we present measurement results obtained from a commercially employed TDMS-based MIMO channel sounder. In the light of the findings of this paper, the results obtained through MIMO channel measurement campaigns using TDMS-based channel sounders should be interpreted with great care.Comment: 99 pages, 14 figures, submitted to IEEE Transactions on Information Theor

Antenna selection and performance analysis of MIMO spatial multiplexing systems

Multiple-input multiple-output spatial multiplexing (MIMO-SM) systems offer an essential benefit referred to as spatial multiplexing gain. Two important signal reception techniques for MIMO-SM systems are the zero-forcing (ZF) and ordered successive interference cancellation (OSIC) as, for example, in the case of the decision-feedback detector (DFD). This thesis studies the communication and signal processing aspects of MIMO-SM. We first investigate the bit error rate (BER) performance of the ZF receiver over transmit correlated Ricean flat-fading channels. In particular, for a MIMO channel with M transmit and N receive antennas, we derive an approximation for the average BER of each sub-stream. A closed-form expression for the optimal transmit correlation coefficient, which achieves the maximum capacity (i.e., uncorrelated case) of two-input two-output spatial multiplexing (TITO-SM) systems, is presented. We further propose an antenna selection (AS) approach for the DFD over independent Rayleigh flat-fading channels. The selected transmit antennas are those that maximize both the post-processing signal-to-noise ratio (SNR) at the receiver end, and the system capacity. An upper bound on the outage probability for the AS approach is derived. It is shown that the AS approach achieves a performance comparable to optimal capacity-based selection based on exhaustive search, but at a lower complexity. Finally, we investigate a cross-layer transmit AS approach for the DFD over spatially correlated Ricean flat-fading channels. The selected transmit antennas are those that maximize the link layer throughput of correlated MIMO channels. A closed-form expression for the system throughput with perfect channel estimation is first derived. We further analyze the system performance with pilot-aided channel estimation. In that, we derive a closed-form expression for the post-detection signal-to-noise-plus-interference ratio (SNIR) of each transmitted substream, conditioned on the estimated channels. The derived SNIR is then used to evaluate the overall system throughput. It is observed that the cross-layer AS approach always assigns the transmission to the antenna combination which sees better channel conditions, resulting in a substantial improvement over the optimal capacity-based AS approach. Considering a training-based channel estimation technique, we compare the performance of the proposed cross-layer AS with that of optimal capacity-based AS when employed with a training-based channel estimation. Our results show that the latter is more robust to imperfect channel estimation. However, in all cases, the cross-layer AS delivers higher throughput gains than the capacity-based A

Experimental statistical channel modelling for advanced wireless communication systems in indoor environments

Draadloze communicatiesystemen voor mobiele telefonie en draadloos internet zijn onmisbaar geworden in het dagelijkse leven. De grootste troef van draadloze communicatie over bedrade communicatie is de toegenomen mobiliteit. Draadloze communicatie heeft evenwel ook één groot nadeel, namelijk de onzekerheid over de kwaliteit van de link tussen zender en ontvanger. Waar bedrade communicatie een doorgedreven ontwerp van het kanaal tussen zender en ontvanger (d.i. de kabel) toelaat, is het ontwerp van het draadloze kanaal (d.i. de omgeving) bijna onmogelijk. Desondanks kunnen wel modellen van de propagatie van draadloze signalen opgesteld worden voor verschillende types omgevingen. Deze modellen laten toe om de betrouwbaarheid en de performantie van een draadloze link in te schatten. Modellering van draadloze propagatie voor indooromgevingen is het algemeen onderwerp van dit proefschrift. De propagatiemodellering in dit proefschrift betreft drie types indooromgevingen, nl. industriële en kantooromgevingen, en de omgeving binnen in een voertuig. De modellering bestaat uit statistische modellen gebaseerd op veldmetingen in deze omgevingen. Verschillende parameters van draadloze signalen worden onderzocht, zoals de variabiliteit van het signaalvermogen met de afstand en in de tijd, het signaalbereik, de dispersie in het tijdsdomein, de dispersie in het spatiaal domein en het vermogensverlies bij propagatie van buiten naar binnen een voertuig

MIMO channel modelling and simulation for cellular and mobile-to-mobile

Recently, mobile-to-mobile (M2M) communications have received much attention due to several emerging applications, such as wireless mobile ad hoc networks, relay-based cellular networks, and dedicated short range communications (DSRC) for intelligent transportation systems (e.g., IEEE 802.11p standard). Different from conventional fixed-to-mobile (F2M) cellular systems, in M2M systems both the transmitter (Tx) and receiver (Rx) are in motion and often equipped with low elevation antennas. Multiple-input-multiple-output (MIMO) technologies, employing multiple antennas at both the Tx and Rx, have widely been adopted for the third generation (3G) and beyond-3G (B3G) F2M cellular systems due to their potential benefits of improving coverage, link reliability, and overall system capacity. More recently, MIMO has been receiving more and more attention for M2M systems as well. Reliable knowledge of the propagation channel obtained from channel measurements and corresponding channel models serve as the enabling foundation for the design and analysis of MIMO F2M and M2M systems. Furthermore, the development of accurate MIMO F2M and M2M channel simulation models plays a major role in the practical simulation and performance evaluation of these systems. These form the primary motivation behind our research on MIMO channel modelling and simulation for F2M cellular and M2M communication systems. In this thesis, we first propose a new wideband theoretical multiple-ring based MIMO regular-shaped geometry-based stochastic model (RS-GBSM) for non-isotropic scattering F2M macro-cell scenarios and then derive a generic space-time-frequency (STF) correlation function (CF). The proposed theoretical reference wideband model can be reduced to a narrowband one-ring model, a new closed-form STF CF of which is derived as well. Narrowband and wideband sum-of-sinusoids (SoS) simulation models are then developed, demonstrating a good agreement with the corresponding reference models in terms of correlation functions. Secondly, based on a well-known narrowband two-ring single-input single-output (SISO) M2M channel reference model, we propose new deterministic and stochastic SoS simulation models for non-isotropic scattering environments. The proposed deterministic simulator is the first SISO M2M deterministic simulator with good performance, while the proposed stochastic simulator outperforms the existing one in terms of fitting the desired statistical properties of the corresponding reference model. Thirdly, a new adaptive narrowband MIMO M2M RS-GBSM is proposed for nonisotropic scattering environments. To the best of our knowledge, the proposed M2M model is the first RS-GBSM that has the ability to study the impact of the vehicular traffic density on channel statistics. From the proposed theoretical reference model, we comprehensively investigate some important M2M channel statistics including the STF CF, space-Doppler-frequency power spectral density, envelope level crossing rate, and average fade duration. A close agreement between some channel statistics obtained from the proposed reference model and measurement data is observed, confirming the utility of our model. Finally, we extend the above narrowband model to a new wideband MIMO M2M RSGBSM with respect to the frequency-selectivity. The proposed wideband reference model is validated by observing a good match between some statistical properties of the theoretical model and available measurement data. From the wideband reference model, we further design new wideband deterministic and stochastic SoS simulation models. The proposed wideband simulators can be easily reduced to narrowband ones. The utilities of the newly derived narrowband and wideband simulation models are validated by comparing their statistical properties with those of the corresponding reference models. The proposed channel reference models and simulators are expected to be useful for the design, testing, and performance evaluation of future MIMO cellular and M2M communication systems.Scottish Funding Counci

Characterisation and Modelling of Indoor and Short-Range MIMO Communications

Over the last decade, we have witnessed the rapid evolution of Multiple-Input Multiple-Output (MIMO) systems which promise to break the frontiers of conventional architectures and deliver high throughput by employing more than one element at the transmitter (Tx) and receiver (Rx) in order to exploit the spatial domain. This is achieved by transmitting simultaneous data streams from different elements which impinge on the Rx with ideally unique spatial signatures as a result of the propagation paths’ interactions with the surrounding environment. This thesis is oriented to the statistical characterisation and modelling of MIMO systems and particularly of indoor and short-range channels which lend themselves a plethora of modern applications, such as wireless local networks (WLANs), peer-to-peer and vehicular communications. The contributions of the thesis are detailed below. Firstly, an indoor channel model is proposed which decorrelates the full spatial correlation matrix of a 5.2 GHzmeasuredMIMO channel and thereafter assigns the Nakagami-m distribution on the resulting uncorrelated eigenmodes. The choice of the flexible Nakagami-m density was found to better fit the measured data compared to the commonly used Rayleigh and Ricean distributions. In fact, the proposed scheme captures the spatial variations of the measured channel reasonably well and systematically outperforms two known analytical models in terms of information theory and link-level performance. The second contribution introduces an array processing scheme, namely the three-dimensional (3D) frequency domain Space Alternating Generalised Expectation Maximisation (FD-SAGE) algorithm for jointly extracting the dominant paths’ parameters. The scheme exhibits a satisfactory robustness in a synthetic environment even for closely separated sources and is applicable to any array geometry as long as its manifold is known. The algorithm is further applied to the same set of raw data so that different global spatial parameters of interest are determined; these are the multipath clustering, azimuth spreads and inter-dependency of the spatial domains. The third contribution covers the case of short-range communications which have nowadays emerged as a hot topic in the area of wireless networks. The main focus is on dual-branch MIMO Ricean systems for which a design methodology to achieve maximum capacities in the presence of Line-of-Sight (LoS) components is proposed. Moreover, a statistical eigenanalysis of these configurations is performed and novel closed-formulae for the marginal eigenvalue and condition number statistics are derived. These formulae are further used to develop an adaptive detector (AD) whose aim is to reduce the feasibility cost and complexity of Maximum Likelihood (ML)-based MIMO receivers. Finally, a tractable novel upper bound on the ergodic capacity of the above mentioned MIMO systems is presented which relies on a fundamental power constraint. The bound is sufficiently tight and applicable for arbitrary rank of the mean channel matrix, Signal-to-Noise ratio (SNR) and takes the effects of spatial correlation at both ends into account. More importantly, it includes previously reported capacity bounds as special cases