Implicit feed-forward compensated op-amp with split pairs

Disclosed are systems implementing an implicit Feed-Forward Compensated (FFC) op-amp, where the main FFC port is realized by the P-side of the CMOS input structure of the 2nd and 3rd stages of the op-amp, while the main signal path is through the N-side. According to some embodiments, to balance the relative strengths of the main path and feed-forward paths, the 2nd-stage NMOS input pair is split into two pairs, one is used to route the main path while the other is used for auxiliary FFC. The disclosed implicit FCC op-amp is unconditionally stable with adequate phase lead. According to some embodiments, the disclosed op-amp, which may be a wide-band op-amp, can be used in highly linear applications operative at intermediate frequency (IF), such as signal buffers for high-performance data converters or radio-frequency (RF) modulators and demodulators, continuous-time (CT) filters or sigma-delta data converters.Board of Regents, University of Texas Syste

Design and implementation of a wideband sigma delta ADC

Abstract. High-speed and wideband ADCs have become increasingly important in response to the growing demand for high-speed wireless communication services. Continuous time sigma delta modulators (CTƩ∆M), well-known for their oversampling and noise shaping properties, offer a promising solution for low-power and high-speed design in wireless applications. The objective of this thesis is to design and implement a wideband CTƩ∆M for a global navigation satellite system(GNSS) receiver. The targeted modulator architecture is a 3rdorder single-bit CTƩ∆M, specifically designed to operate within a 15 MHz signal bandwidth. With an oversampling ratio of 25, the ADC’s sampling frequency is set at 768 MHz. The design goal is to achieve a theoretical signal to noise ratio (SNR) of 55 dB. This thesis focuses on the design and implementation of the CTƩ∆M, building upon the principles of a discrete time Ʃ∆ modulator, and leveraging system-level simulation and formulations. A detailed explanation of the coefficient calculation procedure specific to CTƩ∆ modulators is provided, along with a "top-down" design approach that ensures the specified requirements are met. MATLAB scripts for coefficient calculation are also included. To overcome the challenges associated with the implementation of CTƩ∆ modulators, particularly excess loop delay and clock jitter sensitivity, this thesis explores two key strategies: the introduction of a delay compensation path and the utilization of a finite impulse response (FIR) feedback DAC. By incorporating a delay compensation path, the stability of the modulator can be ensured and its noise transfer function (NTF) can be restored. Additionally, the integration of an FIR feedback DAC addresses the issue of clock jitter sensitivity, enhancing the overall performance and robustness of the CTƩ∆M. The CTƩ∆Ms employ the cascade of integrators with feed forward (CIFF) and cascade of integrators with feedforward and feedback (CIFF-B) topologies, with a particular emphasis on the CIFF-B configuration using 22nm CMOS technology node and a supply voltage of 0.8 V. Various simulations are performed to validate the modulator’s performance. The simulation results demonstrate an achievable SNR of 55 dB with a power consumption of 1.36 mW. Furthermore, the adoption of NTF zero optimization techniques enhances the SNR to 62 dB.Laajakaistaisen jatkuva-aikaisen sigma delta-AD-muuntimen suunnittelu ja toteutus. Tiivistelmä. Nopeat ja laajakaistaiset AD-muuntimet ovat tulleet entistä tärkeämmiksi nopeiden langattomien kommunikaatiopalvelujen kysynnän kasvaessa. Jatkuva-aikaiset sigma delta -modulaattorit (CTƩ∆M), joissa käytetään ylinäytteistystä ja kohinanmuokkausta, tarjoavat lupaavan ratkaisun matalan tehonkulutuksen ja nopeiden langattomien sovellusten suunnitteluun. Tämän työn tarkoituksena on suunnitella ja toteuttaa laajakaistainen jatkuva -aikainen sigma delta -modulaattori satelliittipaikannusjärjestelmien (GNSS) vastaanottimeen. Arkkitehtuuriltaan modulaattori on kolmannen asteen 1-bittinen CTƩ∆M, jolla on 15MHz:n signaalikaistanleveys. Ylinäytteistyssuhde on 25 ja AD muuntimen näytteistystaajuus 768 MHz. Tavoitteena on saavuttaa teoreettinen 55 dB signaalikohinasuhde (SNR). Tämä työ keskittyy jatkuva-aikaisen sigma delta -modulaattorin suunnitteluun ja toteutukseen, perustuen diskreettiaikaisen Ʃ∆-modulaattorin periaatteisiin ja systeemitason simulointiin ja mallitukseen. Jatkuva-aikaisen sigma delta -modulaattorin kertoimien laskentamenetelmä esitetään yksityiskohtaisesti, ja vaatimusten täyttyminen varmistetaan “top-down” -suunnitteluperiaatteella. Liitteenä on kertoimien laskemiseen käytetty MATLAB-koodi. Jatkuva-aikaisten sigma delta -modulaattoreiden erityishaasteiden, liian pitkän silmukkaviiveen ja kellojitterin herkkyyden, voittamiseksi tutkitaan kahta strategiaa, viiveen kompensointipolkua ja FIR takaisinkytkentä -DA muunninta. Viivekompensointipolkua käyttämällä modulaattorin stabiilisuus ja kohinansuodatusfunktio saadaan varmistettua ja korjattua. Lisäksi FIR takaisinkytkentä -DA-muuntimen käyttö pienentää kellojitteriherkkyyttä, parantaen jatkuva aikaisen sigma delta -modulaattorin kokonaissuorituskykyä ja luotettavuutta. Toteutetuissa jatkuva-aikaisissa sigma delta -modulaattoreissa on kytketty peräkkäin integraattoreita myötäkytkentärakenteella (CIFF) ja toisessa sekä myötä- että takaisinkytkentärakenteella (CIFF-B). Päähuomio on CIFF-B rakenteessa, joka toteutetaan 22nm CMOS prosessissa käyttäen 0.8 voltin käyttöjännitettä. Suorityskyky varmistetaan erilaisilla simuloinneilla, joiden perusteella 55 dB SNR saavutetaan 1.36 mW tehonkulutuksella. Lisäksi kohinanmuokkausfunktion optimoinnilla SNR saadaan nostettua 62 desibeliin

A Millimeter-Wave Coexistent RFIC Receiver Architecture in 0.18-µm SiGe BiCMOS for Radar and Communication Systems

Innovative circuit architectures and techniques to enhance the performance of several key BiCMOS RFIC building blocks applied in radar and wireless communication systems operating at the millimeter-wave frequencies are addressed in this dissertation. The former encapsulates the development of an advanced, low-cost and miniature millimeter-wave coexistent current mode direct conversion receiver for short-range, high-resolution radar and high data rate communication systems. A new class of broadband low power consumption active balun-LNA consisting of two common emitters amplifiers mutually coupled thru an AC stacked transformer for power saving and gain boosting. The active balun-LNA exhibits new high linearity technique using a constant gm cell transconductance independent of input-outputs variations based on equal emitters’ area ratios. A novel multi-stages active balun-LNA with innovative technique to mitigate amplitude and phase imbalances is proposed. The new multi-stages balun-LNA technique consists of distributed feed-forward averaging recycles correction for amplitude and phase errors and is insensitive to unequal paths parasitic from input to outputs. The distributed averaging recycles correction technique resolves the amplitude and phase errors residuals in a multi-iterative process. The new multi-stages balun-LNA averaging correction technique is frequency independent and can perform amplitude and phase calibrations without relying on passive lumped elements for compensation. The multi-stage balun-LNA exhibits excellent performance from 10 to 50 GHz with amplitude and phase mismatches less than 0.7 dB and 2.86º, respectively. Furthermore, the new multi-stages balun-LNA operates in current mode and shows high linearity with low power consumption. The unique balun-LNA design can operates well into mm-wave regions and is an integral block of the mm-wave radar and communication systems. The integration of several RFIC blocks constitutes the broadband millimeter-wave coexistent current mode direct conversion receiver architecture operating from 22- 44 GHz. The system and architectural level analysis provide a unique understanding into the receiver characteristics and design trade-offs. The RF front-end is based on the broadband multi-stages active balun-LNA coupled into a fully balanced passive mixer with an all-pass in-phase/quadrature phase generator. The trans-impedance amplifier converts the input signal current into a voltage gain at the outputs. Simultaneously, the high power input signal current is channelized into an anti-aliasing filter with 20 dB rejection for out of band interferers. In addition, the dissertation demonstrates a wide dynamic range system with small die area, cost effective and very low power consumption

A Millimeter-Wave Coexistent RFIC Receiver Architecture in 0.18-µm SiGe BiCMOS for Radar and Communication Systems

Innovative circuit architectures and techniques to enhance the performance of several key BiCMOS RFIC building blocks applied in radar and wireless communication systems operating at the millimeter-wave frequencies are addressed in this dissertation. The former encapsulates the development of an advanced, low-cost and miniature millimeter-wave coexistent current mode direct conversion receiver for short-range, high-resolution radar and high data rate communication systems. A new class of broadband low power consumption active balun-LNA consisting of two common emitters amplifiers mutually coupled thru an AC stacked transformer for power saving and gain boosting. The active balun-LNA exhibits new high linearity technique using a constant gm cell transconductance independent of input-outputs variations based on equal emitters’ area ratios. A novel multi-stages active balun-LNA with innovative technique to mitigate amplitude and phase imbalances is proposed. The new multi-stages balun-LNA technique consists of distributed feed-forward averaging recycles correction for amplitude and phase errors and is insensitive to unequal paths parasitic from input to outputs. The distributed averaging recycles correction technique resolves the amplitude and phase errors residuals in a multi-iterative process. The new multi-stages balun-LNA averaging correction technique is frequency independent and can perform amplitude and phase calibrations without relying on passive lumped elements for compensation. The multi-stage balun-LNA exhibits excellent performance from 10 to 50 GHz with amplitude and phase mismatches less than 0.7 dB and 2.86º, respectively. Furthermore, the new multi-stages balun-LNA operates in current mode and shows high linearity with low power consumption. The unique balun-LNA design can operates well into mm-wave regions and is an integral block of the mm-wave radar and communication systems. The integration of several RFIC blocks constitutes the broadband millimeter-wave coexistent current mode direct conversion receiver architecture operating from 22- 44 GHz. The system and architectural level analysis provide a unique understanding into the receiver characteristics and design trade-offs. The RF front-end is based on the broadband multi-stages active balun-LNA coupled into a fully balanced passive mixer with an all-pass in-phase/quadrature phase generator. The trans-impedance amplifier converts the input signal current into a voltage gain at the outputs. Simultaneously, the high power input signal current is channelized into an anti-aliasing filter with 20 dB rejection for out of band interferers. In addition, the dissertation demonstrates a wide dynamic range system with small die area, cost effective and very low power consumption

Filter Design Considerations for High Performance Continuous-Time Low-Pass Sigma-Delta ADC

Continuous-time filters are critical components in the implementation of large bandwidth, high frequency, and high resolution continuous-time (CT) sigma-delta (ΣΔ) analog-to-digital converters (ADCs). The loop filter defines the noise-transfer function (NTF) and hence the quantization noise-shaping behavior of the ΣΔ modulator, and becomes the most critical performance determining part in ΣΔ ADC. This thesis work presents the design considerations for the loop filter in low-pass CT ΣΔ ADC with 12-bits resolution in 25MHz bandwidth and low power consumption using 0.18μm CMOS technology. Continuous-time filters are more suitable than discrete-time filters due to relaxed amplifier bandwidth requirements for high frequency ΣΔ ADCs. A fifth-order low-pass filter with cut-off frequency of 25 MHz was designed to meet the dynamic range requirement of the ADC. An active RC topology was chosen for the implementation of the loop filter, which can provide high dynamic range required by the ΣΔ ADC. The design of a summing amplifier and a novel method for adjusting the group delay in the fast path provided by a secondary feedback DAC of the ΣΔ ADC are presented in detail. The ADC was fabricated using Jazz 0.18μm CMOS technology. The implementation issues of OTAs with high-linearity and low-noise performance suitable for the broadband ADC applications are also analyzed in this work. Important design equations pertaining to the linearity and noise performance of the Gm-C biquad filters are presented. A Gm-C biquad with 100MHz center frequency and quality factor 10 was designed as a prototype to confirm with the theoretical design equations. Transistor level circuit implementation of all the analog modules was completed in a standard 0.18μm CMOS process

Design of Inverter Based CMOS Amplifiers in Deep Nanoscale Technologies

In this work, it is proposed a fully differential ring amplifier topology with a deadzone voltage created by a CMOS resistor with a biasing circuit to increase the robustness over PVT variations. The study focuses on analyzing the performance of the ring amplifier over process, temperature, and supply voltage variations, in order to guarantee a viable industrial employment in a 7 nm FinFET CMOS technology node for being used as residue amplifier in ADCs. A ring amplifier is a small modular amplifier, derived from a ring oscillator. It is simple enough that it can quickly be designed using only a few inverters, capacitors, and switches. It can amplify with rail-to-rail output swing, competently charge large capacitive loads using slew-based charging, and scale well in performance according to process trends. In typical process corner, a gain of 72 dB is achieved with a settling time of 150 ps. Throughout the study, the proposed topology is compared with others presented in literature showing better results over corners and presenting a faster response. The proposed topology isn’t yet suitable for industry use, because it presents one corner significantly slower than the rest, namely process corner FF 125 °C, and process corner FS -40 °C with a small oscillation throughout the entire amplification period. Nevertheless, it proved itself to be a promising technique, showing a high gain and a fast settling without oscillation phase, with room for improvement.Neste trabalho, é proposta uma topologia de ring amplifier com a deadzone a ser criada através de uma resistência CMOS com um circuito de polarização para aumentar a robustez para as variações PVT. O estudo foca-se em analisar a performance do ring amplifier nas variações de processo, temperatura e tensão de alimentação, de forma a garantir um uso viável em indústria na tecnologia de 7 nm FinFET CMOS, para ser usado como amplificador de resíduo em ADCs. Um ring amplifier é um pequeno amplificador modular, derivado do ring oscillator. É simples o suficiente para ser facilmente projetado usando apenas poucos inversores, condensadores e interruptores. Consegue amplificar com rail-to-rail output swing, carregar grandes cargas capacitivas com carregamento slew-based e escalar bem em termos de performance de acordo com o processo. No typical process corner, foi obtido um ganho de 72 dB com um tempo de estabilização de 150 ps. Durante o estudo, a topologia proposta é comparada com outras presentes na literatura mostrando melhores resultados over corners e apresentando uma resposta mais rápida. A topologia proposta ainda não está preparada para uso industrial uma vez que apresenta um corner significativamente mais lento que os restantes, nomeadamente, process corner FF 125 °C, e outro process corner, FS -40 °C, com uma pequena oscilação durante todo o período de amplificação. Todavia, provou ser uma técnica promissora, apresentando um ganho elevado e uma rápida estabilização sem fase de oscilação, com espaço para melhoria

Design and Applications of Minimally Invasive All-Pole Analog Filters

A new design technique for minimally invasive all-pole analog lowpass filters is introduced and the concept of minimally invasive filtering has been generalized for higher orders both in voltage-mode and current-mode operations. The proposed fully differential solution has minimal impact on the in-band signal in terms of added noise and nonlinearity, whereas it has comparable performance for out-of-band signals using smaller number of active devices. Extending the concept of current-mode minimally invasive filters, a novel baseband circuit with third order filtering has been designed, which has comparable linearity and noise with approximately half the power consumption when compared to the conventional solution. The proposed baseband circuit has a bandwidth of 10MHz, achieves 44dB rejection at 50MHz (40dB in post-layout simulations), low broad-band input impedance of 10.16ohm with a comparable noise and linearity at a lower power consumption when compared to a third order conventional circuit. The circuit has been designed in TSMC 130nm technology and is integrated with a broad-band receiver front-end including an LNA and a mixer

HIGH PERFORMANCE CMOS WIDE-BAND RF FRONT-END WITH SUBTHRESHOLD OUT OF BAND SENSING

In future, the radar/satellite wireless communication devices must support multiple standards and should be designed in the form of system-on-chip (SoC) so that a significant reduction happen on cost, area, pins, and power etc. However, in such device, the design of a fully on-chip CMOS wideband receiver front-end that can process several radar/satellite signal simultaneously becomes a multifold complex problem. Further, the inherent high-power out-of-band (OB) blockers in radio spectrum will make the receiver more non-linear, even sometimes saturate the receiver. Therefore, the proper blocker rejection techniques need to be incorporated. The primary focus of this research work is the development of a CMOS high-performance low noise wideband receiver architecture with a subthreshold out of band sensing receiver. Further, the various reconfigurable mixer architectures are proposed for performance adaptability of a wideband receiver for incoming standards. Firstly, a high-performance low- noise bandwidthenhanced fully differential receiver is proposed. The receiver composed of a composite transistor pair noise canceled low noise amplifier (LNA), multi-gate-transistor (MGTR) trans-conductor amplifier, and passive switching quad followed by Tow Thomas bi-quad second order filter based tarns-impedance amplifier. An inductive degenerative technique with low-VT CMOS architecture in LNA helps to improve the bandwidth and noise figure of the receiver. The full receiver system is designed in UMC 65nm CMOS technology and measured. The packaged LNA provides a power gain 12dB (including buffer) with a 3dB bandwidth of 0.3G – 3G, noise figure of 1.8 dB having a power consumption of 18.75mW with an active area of 1.2mm*1mm. The measured receiver shows 37dB gain at 5MHz IF frequency with 1.85dB noise figure and IIP3 of +6dBm, occupies 2mm*1.2mm area with 44.5mW of power consumption. Secondly, a 3GHz-5GHz auxiliary subthreshold receiver is proposed to estimate the out of blocker power. As a redundant block in the system, the cost and power minimization of the auxiliary receiver are achieved via subthreshold circuit design techniques and implementing the design in higher technology node (180nm CMOS). The packaged auxiliary receiver gives a voltage gain of 20dB gain, the noise figure of 8.9dB noise figure, IIP3 of -10dBm and 2G-5GHz bandwidth with 3.02mW power consumption. As per the knowledge, the measured results of proposed main-high-performancereceiver and auxiliary-subthreshold-receiver are best in state of art design. Finally, the various viii reconfigurable mixers architectures are proposed to reconfigure the main-receiver performance according to the requirement of the selected communication standard. The down conversion mixers configurability are in the form of active/passive and Input (RF) and output (IF) bandwidth reconfigurability. All designs are simulated in 65nm CMOS technology. To validate the concept, the active/ passive reconfigurable mixer configuration is fabricated and measured. Measured result shows a conversion gain of 29.2 dB and 25.5 dB, noise figure of 7.7 dB and 10.2 dB, IIP3 of -11.9 dBm and 6.5 dBm in active and passive mode respectively. It consumes a power 9.24mW and 9.36mW in passive and active case with a bandwidth of 1 to 5.5 GHz and 0.5 to 5.1 GHz for active/passive case respectively