Runtime Scheduling, Allocation, and Execution of Real-Time Hardware Tasks onto Xilinx FPGAs Subject to Fault Occurrence

This paper describes a novel way to exploit the computation capabilities delivered by modern Field-Programmable Gate Arrays (FPGAs), not only towards a higher performance, but also towards an improved reliability. Computation-specific pieces of circuitry are dynamically scheduled and allocated to different resources on the chip based on a set of novel algorithms which are described in detail in this article. These algorithms consider most of the technological constraints existing in modern partially reconfigurable FPGAs as well as spontaneously occurring faults and emerging permanent damage in the silicon substrate of the chip. In addition, the algorithms target other important aspects such as communications and synchronization among the different computations that are carried out, either concurrently or at different times. The effectiveness of the proposed algorithms is tested by means of a wide range of synthetic simulations, and, notably, a proof-of-concept implementation of them using real FPGA hardware is outlined

Efficient Algorithms for Online Task Placement on Runtime Partially Reconfigurable FPGA

Recent generations of FPGAs allow run-time partial reconfiguration. One of the challenging problems in such a multitasking systems is online placement of task. Many online task placement algorithms designed for such partially reconfigurable systems have been proposed to provide efficient and fast task placement. In this paper two different approaches are being used to place the incoming tasks. The first method is uses a run-length based representation that defines the vacant slots on the FPGA. This compact representation allows the algorithm to locate a vacant area suitable to accommodate the incoming task quickly. In the proposed FPGA model, the CLBs are numbered according to Peano Space filling curve model. The second approach is based on harmonic packing. Simulation experiments indicate that proposed techniques result in low ratio of task rejection compared to existing techniques

Task scheduling and placement for reconfigurable devices

Partially reconfigurable devices allow the execution of different tasks at the same time, removing tasks when they finish and inserting new tasks when they arrive. This dissertation investigates scheduling and placing real-time tasks (tasks with deadline) on reconfigurable devices. One basic scheduler is the First-Fit scheduler. By allowing the First-Fit scheduler to retry tasks while they can satisfy their deadlines, we found that its performance can be enhanced to be better than other schedulers. We also proposed a placement idea based on partitioning the reconfigurable area into regions of various widths, assigning a task to a region based on its width. This idea has a similar rejection rate to a First-Fit scheduler that retries placing tasks and performs better than the First-Fit that does not retry tasks. Also, this regions-based scheduling method has a better running time. Managing how the space will be shared among tasks is a problems of interest. The main function of the free-space manager is to maintain information about the free space (areas not used by active tasks) after any placement or deletion of a task. Speed and efficiency of the free-space data structure are important as well as its effect on scheduler performance. We introduce the use of maximal horizontal strips and maximal vertical strips to represent free space. This resulted in a faster free space manager compared to what has been used in the area. Most researchers in the area of scheduling on reconfigurable devices assumed a homogeneous FPGA with only CLBs in the reconfigurable area. Most reconfigurable devices offered in the market, however, are not homogeneous but heterogeneous with other components between CLBs. We studied the effect of heterogeneity on the performance of schedulers designed for a homogeneous structure. We found that current schedulers result in worse performance when applied to a heterogeneous structure, but by simple modifications, we can apply them to a heterogeneous structure and achieve good performance. Consequently, the approach of studying homogeneous FPGAs is a valid one, as the scheduling ideas discovered there do carry over to heterogeneous FPGAs

Resource-efficient dynamic partial reconfiguration on FPGAs for space instruments

Field-Programmable Gate Arrays (FPGAs) provide highly flexible platforms to implement sophisticated data processing for scientific space instruments. The dynamic partial reconfiguration (DPR) capability of FPGAs allows it to schedule HW tasks. While this feature adds another dimension of processing power that can be exploited without significantly increasing system complexity and power consumption, there are still several challenges for an efficient DPR use. State-of-the-art concepts concentrate either on resource-efficient implementations at design time or flexible HW task scheduling at runtime. In this paper we propose a balanced algorithm that considers both optimization goals and is well suited for resource-limited space applications

Defragmenting the Module Layout of a Partially Reconfigurable Device

Modern generations of field-programmable gate arrays (FPGAs) allow for partial reconfiguration. In an online context, where the sequence of modules to be loaded on the FPGA is unknown beforehand, repeated insertion and deletion of modules leads to progressive fragmentation of the available space, making defragmentation an important issue. We address this problem by propose an online and an offline component for the defragmentation of the available space. We consider defragmenting the module layout on a reconfigurable device. This corresponds to solving a two-dimensional strip packing problem. Problems of this type are NP-hard in the strong sense, and previous algorithmic results are rather limited. Based on a graph-theoretic characterization of feasible packings, we develop a method that can solve two-dimensional defragmentation instances of practical size to optimality. Our approach is validated for a set of benchmark instances.Comment: 10 pages, 11 figures, 1 table, Latex, to appear in "Engineering of Reconfigurable Systems and Algorithms" as a "Distinguished Paper

A Field Programmable Gate Array Architecture for Two-Dimensional Partial Reconfiguration

Reconfigurable machines can accelerate many applications by adapting to their needs through hardware reconfiguration. Partial reconfiguration allows the reconfiguration of a portion of a chip while the rest of the chip is busy working on tasks. Operating system models have been proposed for partially reconfigurable machines to handle the scheduling and placement of tasks. They are called OS4RC in this dissertation. The main goal of this research is to address some problems that come from the gap between OS4RC and existing chip architectures and the gap between OS4RC models and practical applications. Some existing OS4RC models are based on an impractical assumption that there is no data exchange channel between IP (Intellectual Property) circuits residing on a Field Programmable Gate Array (FPGA) chip and between an IP circuit and FPGA I/O pins. For models that do not have such an assumption, their inter-IP communication channels have severe drawbacks. Those channels do not work well with 2-D partial reconfiguration. They are not suitable for intensive data stream processing. And frequently they are very complicated to design and very expensive. To address these problems, a new chip architecture that can better support inter-IP and IP-I/O communication is proposed and a corresponding OS4RC kernel is then specified. The proposed FPGA architecture is based on an array of clusters of configurable logic blocks, with each cluster serving as a partial reconfiguration unit, and a mesh of segmented buses that provides inter-IP and IP-I/O communication channels. The proposed OS4RC kernel takes care of the scheduling, placement, and routing of circuits under the constraints of the proposed architecture. Features of the new architecture in turns reduce the kernel execution times and enable the runtime scheduling, placement and routing. The area cost and the configuration memory size of the new chip architecture are calculated and analyzed. And the efficiency of the OS4RC kernel is evaluated via simulation using three different task models

An FPGA Task Placement Algorithm Using Reflected Binary Gray Space Filling Curve

With the arrival of partial reconfiguration technology, modern FPGAs support tasks that can be loaded in (removed from) the FPGA individually without interrupting other tasks already running on the same FPGA. Many online task placement algorithms designed for such partially reconfigurable systems have been proposed to provide efficient and fast task placement. A new approach for online placement of modules on reconfigurable devices, by managing the free space using a run-length based representation. This representation allows the algorithm to insert or delete tasks quickly and also to calculate the fragmentation easily. In the proposed FPGA model, the CLBs are numbered according to reflected binary gray space filling curve model. The search algorithm will quickly identify a placement for the incoming task based on first fit mode or a fragmentation aware best fit mode. Simulation experiments indicate that the proposed techniques result in a low ratio of task rejection and high FPGA utilization compared to existing techniques

Dynamic partial reconfiguration management for high performance and reliability in FPGAs

Modern Field-Programmable Gate Arrays (FPGAs) are no longer used to implement small “glue logic” circuitries. The high-density of reconfigurable logic resources in today’s FPGAs enable the implementation of large systems in a single chip. FPGAs are highly flexible devices; their functionality can be altered by simply loading a new binary file in their configuration memory. While the flexibility of FPGAs is comparable to General-Purpose Processors (GPPs), in the sense that different functions can be performed using the same hardware, the performance gain that can be achieved using FPGAs can be orders of magnitudes higher as FPGAs offer the ability for customisation of parallel computational architectures. Dynamic Partial Reconfiguration (DPR) allows for changing the functionality of certain blocks on the chip while the rest of the FPGA is operational. DPR has sparked the interest of researchers to explore new computational platforms where computational tasks are off-loaded from a main CPU to be executed using dedicated reconfigurable hardware accelerators configured on demand at run-time. By having a battery of custom accelerators which can be swapped in and out of the FPGA at runtime, a higher computational density can be achieved compared to static systems where the accelerators are bound to fixed locations within the chip. Furthermore, the ability of relocating these accelerators across several locations on the chip allows for the implementation of adaptive systems which can mitigate emerging faults in the FPGA chip when operating in harsh environments. By porting the appropriate fault mitigation techniques in such computational platforms, the advantages of FPGAs can be harnessed in different applications in space and military electronics where FPGAs are usually seen as unreliable devices due to their sensitivity to radiation and extreme environmental conditions. In light of the above, this thesis investigates the deployment of DPR as: 1) a method for enhancing performance by efficient exploitation of the FPGA resources, and 2) a method for enhancing the reliability of systems intended to operate in harsh environments. Achieving optimal performance in such systems requires an efficient internal configuration management system to manage the reconfiguration and execution of the reconfigurable modules in the FPGA. In addition, the system needs to support “fault-resilience” features by integrating parameterisable fault detection and recovery capabilities to meet the reliability standard of fault-tolerant applications. This thesis addresses all the design and implementation aspects of an Internal Configuration Manger (ICM) which supports a novel bitstream relocation model to enable the placement of relocatable accelerators across several locations on the FPGA chip. In addition to supporting all the configuration capabilities required to implement a Reconfigurable Operating System (ROS), the proposed ICM also supports the novel multiple-clone configuration technique which allows for cloning several instances of the same hardware accelerator at the same time resulting in much shorter configuration time compared to traditional configuration techniques. A faulttolerant (FT) version of the proposed ICM which supports a comprehensive faultrecovery scheme is also introduced in this thesis. The proposed FT-ICM is designed with a much smaller area footprint compared to Triple Modular Redundancy (TMR) hardening techniques while keeping a comparable level of fault-resilience. The capabilities of the proposed ICM system are demonstrated with two novel applications. The first application demonstrates a proof-of-concept reliable FPGA server solution used for executing encryption/decryption queries. The proposed server deploys bitstream relocation and modular redundancy to mitigate both permanent and transient faults in the device. It also deploys a novel Built-In Self- Test (BIST) diagnosis scheme, specifically designed to detect emerging permanent faults in the system at run-time. The second application is a data mining application where DPR is used to increase the computational density of a system used to implement the Frequent Itemset Mining (FIM) problem