Expanded operational capabilities of the Langley Mach 7 Scramjet test facility

An experimental research program conducted to expand the operational capabilities of the NASA Langley Mach 7 Scramjet Test Facility is described. Previous scramjet testing in this facility was limited to a single simulated flight condition of Mach 6.9 at an altitude of 115,300 ft. The arc heater research demonstrates the potential of the facility for scramjet testing at simulated flight conditions from Mach 4 (at altitudes from 77,000 to 114,000 ft) to Mach 7 (at latitudes from 108,000 to 149,000 ft). Arc heater electrical characteristics, operational problems, measurements of nitrogen oxide contaminants, and total-temperature profiles are discussed

Detailed modal testing of a solid rocket motor using a portable test system

Modern analytical techniques have expended the ability to evaluate solid rocket motors used in launch vehicles. As more detailed models of solid rocket motors were developed, testing methods were required to verify the models. Experimental modal analysis (modal testing) of space structures and launch vehicles has been a requirement for model validation for many years. However, previous testing of solid rocket motors has not typically involved dynamic modal testing of full scale motors for verification of solid propellant or system assembly properties. Innovative approaches to the testing of solid rocket motors were developed and modal testing of a full scale, two segment Titan 34D Solid Rocket Motor (SRM) was performed to validate detailed computer modeling. Special modifications were made to convert an existing facility into a temporary modal test facility which would accommodate the test article. The assembly of conventional data acquisition equipment into a multiple channel count portable system has made modal testing in the field feasible. Special purpose hydraulic exciters were configured to apply the dynamic driving forces required. All instrumentation and data collection equipment were installed at the test site for the duration of the test program and removed upon completion. Conversion of an existing test facility into a temporary modal test facility, and use of a multiple channel count portable test data acquisition system allowed all test objectives to be met and resulted in validation of the computer model in a minimum time

Catalytic ignition of hydrogen/oxygen

An experimental program was conducted to evaluate the catalytic ignition of gaseous hydrogen and oxygen. Shell 405 granular catalyst and a unique monolithic sponge catalyst were tested. Mixture ratio, mass flow rate, propellant inlet temperature, and back pressure were varied parametrically in testing to determine the operational limits of a catalytic igniter. The test results showed that the gaseous hydrogen/oxygen propellant combination can be ignited catalytically using Shell 405 catalyst over a wide range of mixture ratios, mass flow rates, and propellant injection temperatures. These operating conditions must be optimized to ensure reliable ignition for an extended period of time. The results of the experimental program and the established operational limits for a catalytic igniter using both the granular and monolithic catalysts are presented. The capabilities of a facility constructed to conduct the igniter testing and the advantages of a catalytic igniter over other ignition systems for gaseous hydrogen and oxygen are also discussed

Possible safety hazards associated with the operation of the 0.3-m transonic cryogenic tunnel at the NASA Langley Research Center

The 0.3 m Transonic Cryogenic Tunnel (TCT) at the NASA Langley Research Center was built in 1973 as a facility intended to be used for no more than 60 hours in order to verify the validity of the cryogenic wind tunnel concept at transonic speeds. The role of the 0.3 m TCT has gradually changed until now, after over 3000 hours of operation, it is classified as a major NASA research facility and, under the administration of the Experimental Techniques Branch, it is used extensively for the testing of airfoils at high Reynolds numbers and for the development of various technologies related to the efficient operation and use of cryogenic wind tunnels. The purpose of this report is to document the results of a recent safety analysis of the 0.3 m TCT facility. This analysis was made as part of an on going program with the Experimental Techniques Branch designed to ensure that the existing equipment and current operating procedures of the 0.3 m TCT facility are acceptable in terms of today's standards of safety for cryogenic systems

Status of CLIC High-gradient Studies

The recent RF structure testing program carried out in the CLIC Test Facility, CTF II, is described. The main objectives of the testing program have been to gain an insight into the physical processes involved in breakdown and damage, to isolate parameters that influence breakdown and damage, and to determine gradient limits for 30 GHz structures. The layout of CTFII in the new 'Test Stand' configuration, the instrumentation used to study breakdown and the experimental results are summarised. The new results are compared to previously published results at 11, 30 and 33 GHz produced in the context of the CLIC study

Summary of Rocketdyne Engine A5 Rocket Based Combined Cycle Testing

Rocketdyne Propulsion and Power (RPP) has completed a highly successful experimental test program of an advanced rocket based combined cycle (RBCC) propulsion system. The test program was conducted as part of the Advanced Reusable Technology program directed by NASA-MSFC to demonstrate technologies for low-cost access to space. Testing was conducted in the new GASL Flight Acceleration Simulation Test (FAST) facility at sea level (Mach 0), Mach 3.0 - 4.0, and vacuum flight conditions. Significant achievements obtained during the test program include 1) demonstration of engine operation in air-augmented rocket mode (AAR), ramjet mode and rocket mode and 2) smooth transition from AAR to ramjet mode operation. Testing in the fourth mode (scramjet) is scheduled for November 1998

Experimental and analytical studies of flow through a ventral and axial exhaust nozzle system for STOVL aircraft

Flow through a combined ventral and axial exhaust nozzle system was studied experimentally and analytically. The work is part of an ongoing propulsion technology effort at NASA Lewis Research Center for short takeoff, vertical landing (STOVL) aircraft. The experimental investigation was done on the NASA Lewis Powered Lift Facility. The experiment consisted of performance testing over a range of tailpipe pressure ratios from 1 to 3.2 and flow visualization. The analytical investigation consisted of modeling the same configuration and solving for the flow using the PARC3D computational fluid dynamics program. The comparison of experimental and analytical results was very good. The ventral nozzle performance coefficients obtained from both the experimental and analytical studies agreed within 1.2 percent. The net horizontal thrust of the nozzle system contained a significant reverse thrust component created by the flow overturning in the ventral duct. This component resulted in a low net horizontal thrust coefficient. The experimental and analytical studies showed very good agreement in the internal flow patterns

GEN-IV LFR development: Status & perspectives

Since Lead-cooled Fast Reactors (LFR) have been conceptualized in the frame of Generation IV International Forum (GIF), great interest has focused on the development and testing of new technologies related to Heavy Liquid Metal (HLM) nuclear reactors. In this frame, ENEA developed one of the larger European experimental fleet of experimental facilities aiming at investigating HLM thermal-hydraulics, coolant chemistry control, corrosion behavior for structural materials, and at developing components, instrumentations and innovative systems, supported by experiments and numerical tools. The present work aims at highlighting the capabilities and competencies developed by ENEA so far in the frame of the liquid metal technologies for GEN-IV LFR. In particular, an overview on the ongoing R&D experimental program will be depicted considering the actual fleet of facilities: CIRCE, NACIE-UP, LIFUS5, LECOR and HELENA. CIRCE (CIRColazione Eutettico) is the largest HLM pool facility presently in operation worldwide. Full scale component tests, thermal stratification studies, operational and accidental transients and integral tests for the nuclear safety and SGTR (Steam Generator Tube Rupture) events in a large pool system can be studied. NACIE-UP (NAtural CIrculation Experiment-UPgraded) is a loop with a HLM primary and pressurized water secondary side and a 250 kW power Fuel Pin Simulator working in natural and mixed convection. LIFUS5 (lithium for fusion) is a separated effect facility devoted to the HLM/Water interaction. HELENA (HEavy Liquid metal Experimental loop for advanced Nuclear applications) is a pure lead loop with a mechanical pump for high flow rates experiments. LECOR (LEad CORrosion) is a corrosion loop facility with oxygen control system installed. All the experiment actually ongoing on these facilities are described in the paper, depicting their role in the context of GEN-IV LFR development

An Assessment Of Flow Quality In An Open Test Section Wind Tunnel

The subsonic wind tunnel facility at Mississippi State University has been converted to an open test section configuration. An experimental setup was developed which is easily configurable to allow for further research. Measurements of flow quality over select portions of the test section were made to attain a basic understanding of the performance of the new configuration. A program was developed in LabVIEW to control a 3-axis traverse and perform necessary data reduction. The traverse control program was developed to perform data acquisition using a hotilm probe to facilitate the necessary measurements. Data was gathered at two wind tunnel velocity settings over several test section locations. Results of the testing program yielded recommendations on the use of the open configuration. This paper documents the procedure and setup of the testing program to include discussion of the control/data acquisition program and a discussion of the findings and recommendations