71 research outputs found

    Center for Aeronautics and Space Information Sciences

    Get PDF
    This report summarizes the research done during 1991/92 under the Center for Aeronautics and Space Information Science (CASIS) program. The topics covered are computer architecture, networking, and neural nets

    Low Power Analog Processing for Ultra-High-Speed Receivers with RF Correlation

    Get PDF
    Ultra-high-speed data communication receivers (Rxs) conventionally require analog digital converters (ADC)s with high sampling rates which have design challenges in terms of adequate resolution and power. This leads to ultra-high-speed Rxs utilising expensive and bulky high-speed oscilloscopes which are extremely inefficient for demodulation, in terms of power and size. Designing energy-efficient mixed-signal and baseband units for ultra-high-speed Rxs requires a paradigm approach detailed in this paper that circumvents the use of power-hungry ADCs by employing low-power analog processing. The low-power analog Rx employs direct-demodulation with RF correlation using low-power comparators. The Rx is able to support multiple modulations with highest modulation of 16-QAM reported so far for direct-demodulation with RF correlation. Simulations using Matlab, Simulink R2020a® indicate sufficient symbol-error rate (SER) performance at a symbol rate of 8 GS/s for the 71 GHz Urban Micro Cell and 140 GHz indoor channels. Power analysis undertaken with current analog, hybrid and digital beamforming approaches requiring ADCs indicates considerable power savings. This novel approach can be adopted for ultra-high-speed Rxs envisaged for beyond fifth generation (B5G)/sixth generation (6G)/ terahertz (THz) communication without the power-hungry ADCs, leading to low-power integrated design solutions

    The First 15 Years of SEFDM: A Brief Survey

    Get PDF
    Spectrally efficient frequency division multiplexing (SEFDM) is a multi-carrier signal waveform, which achieves higher spectral efficiency, relative to conventional orthogonal frequency division multiplexing (OFDM), by violating the orthogonality of its sub-carriers. This survey provides the history of SEFDM development since its inception in 2003, covering fundamentals and concepts, wireless and optical communications applications, circuit design and experimental testbeds. We focus on work done at UCL and outline work done other universities and research laboratories worldwide. We outline techniques to improve the performance of SEFDM and its practical utility with focus on signal generation, detection and channel estimation

    Network-on-Chip

    Get PDF
    Limitations of bus-based interconnections related to scalability, latency, bandwidth, and power consumption for supporting the related huge number of on-chip resources result in a communication bottleneck. These challenges can be efficiently addressed with the implementation of a network-on-chip (NoC) system. This book gives a detailed analysis of various on-chip communication architectures and covers different areas of NoCs such as potentials, architecture, technical challenges, optimization, design explorations, and research directions. In addition, it discusses current and future trends that could make an impactful and meaningful contribution to the research and design of on-chip communications and NoC systems

    Design of High-Speed Power-Efficient A/D Converters for Wireline ADC-Based Receiver Applications

    Get PDF
    Serial input/output (I/O) data rates are increasing in order to support the explosion in network traffic driven by big data applications such as the Internet of Things (IoT), cloud computing and etc. As the high-speed data symbol times shrink, this results in an increased amount of inter-symbol interference (ISI) for transmission over both severe low-pass electrical channels and dispersive optical channels. This necessitates increased equalization complexity and consideration of advanced modulation schemes, such as four-level pulse amplitude modulation (PAM-4). Serial links which utilize an analog-to-digital converter (ADC) receiver front-end offer a potential solution, as they enable more powerful and flexible digital signal processing (DSP) for equalization and symbol detection and can easily support advanced modulation schemes. Moreover, the DSP back-end provides robustness to process, voltage, and temperature (PVT) variations, benefits from improved area and power with CMOS technology scaling and offers easy design transfer between different technology nodes and thus improved time-to-market. However, ADC-based receivers generally consume higher power relative to their mixed-signal counterparts because of the significant power consumed by conventional multi-GS/s ADC implementations. This motivates exploration of energy-efficient ADC designs with moderate resolution and very high sampling rates to support data rates at or above 50Gb/s. This dissertation presents two power-efficient designs of ≥25GS/s time-interleaved ADCs for ADC-based wireline receivers. The first prototype includes the implementation of a 6b 25GS/s time-interleaved multi-bit search ADC in 65nm CMOS with a soft-decision selection algorithm that provides redundancy for relaxed track-and-hold (T/H) settling and improved metastability tolerance, achieving a figure-of-merit (FoM) of 143fJ/conversion step and 1.76pJ/bit for a PAM-4 receiver design. The second prototype features the design of a 52Gb/s PAM-4 ADC-based receiver in 65nm CMOS, where the front-end consists of a 4-stage continuous-time linear equalizer (CTLE)/variable gain amplifier (VGA) and a 6b 26GS/s time-interleaved SAR ADC with a comparator-assisted 2b/stage structure for reduced digital-to-analog converter (DAC) complexity and a 3-tap embedded feed-forward equalizer (FFE) for relaxed ADC resolution requirement. The receiver front-end achieves an efficiency of 4.53bJ/bit, while compensating for up to 31dB loss with DSP and no transmitter (TX) equalization

    Broadband Receiver Electronic Circuits for Fiber-Optical Communication Systems

    Get PDF
    The exponential growth of internet traffic drives datacenters to constantly improve their capacity. As the copper based network infrastructure is being replaced by fiber-optical interconnects, new industrial standards for higher datarates are required. Several research and industrial organizations are aiming towards 400 Gb Ethernet and beyond, which brings new challenges to the field of high-speed broadband electronic circuit design. Replacing OOK with higher M-ary modulation formats and using higher datarates increases network capacity but at the cost of power. With datacenters rapidly becoming significant energy consumers on the global scale, the energy efficiency of the optical interconnect transceivers takes a primary role in the development of novel systems. There are several additional challenges unique in the design of a broadband shortreach fiber-optical receiver system. The sensitivity of the receiver depends on the noise performance of the PD and the electronics. The overall system noise must be optimized for the specific application, modulation scheme, PD and VCSEL characteristics. The topology of the transimpedance amplifier affects the noise and frequency response of the PD, so the system must be optimized as a whole. Most state-of-the-art receivers are built on high-end semiconductor SiGe and InP technologies. However, there are still several design decisions to be made in order to get low noise, high energy efficiency and adequate bandwidth. In order to overcome the frequency limitations of the optoelectronic components, bandwidth enhancement and channel equalization techniques are used. In this work several different blocks of a receiver system are designed and characterized. A broadband, 50 GHz bandwidth CB-based TIA and a tunable gain equalizer are designed in a 130 nm SiGe BiCMOS process. An ultra-broadband traveling wave amplifier is presented, based on a 250 nm InP DHBT technology demonstrating a 207 GHz bandwidth. Two TIA front-end topologies with 133 GHz bandwidth, a CB and a CE with shunt-shunt feedback, based on a 130 nm InP DHBT technology are designed and compared

    High Speed Reconfigurable NRZ/PAM4 Transceiver Design Techniques

    Get PDF
    While the majority of wireline standards use simple binary non-return-to-zero (NRZ) signaling, four-level pulse-amplitude modulation (PAM4) standards are emerging to increase bandwidth density. This dissertation proposes efficient implementations for high speed NRZ/PAM4 transceivers. The first prototype includes a dual-mode NRZ/PAM4 serial I/O transmitter which can support both modulations with minimum power and hardware overhead. A source-series-terminated (SST) transmitter achieves 1.2Vpp output swing and employs lookup table (LUT) control of a 31-segment output digital-to-analog converter (DAC) to implement 4/2-tap feed-forward equalization (FFE) in NRZ/PAM4 modes, respectively. Transmitter power is improved with low-overhead analog impedance control in the DAC cells and a quarter-rate serializer based on a tri-state inverter-based mux with dynamic pre-driver gates. The transmitter is designed to work with a receiver that implements an NRZ/PAM4 decision feedback equalizer (DFE) that employs 1 finite impulse response (FIR) and 2 infinite impulse response (IIR) taps for first post-cursor and long-tail ISI cancellation, respectively. Fabricated in GP 65-nm CMOS, the transmitter occupies 0.060mm² area and achieves 16Gb/s NRZ and 32Gb/s PAM4 operation at 10.4 and 4.9 mW/Gb/s while operating over channels with 27.6 and 13.5dB loss at Nyquist, respectively. The second prototype presents a 56Gb/s four-level pulse amplitude modulation (PAM4) quarter-rate wireline receiver which is implemented in a 65nm CMOS process. The frontend utilize a single stage continuous time linear equalizer (CTLE) to boost the main cursor and relax the pre-cursor cancelation requirement, requiring only a 2-tap pre-cursor feed-forward equalization (FFE) on the transmitter side. A 2-tap decision feedback equalizer (DFE) with one finite impulse response (FIR) tap and one infinite impulse response (IIR) tap is employed to cancel first post-cursor and longtail inter-symbol interference (ISI). The FIR tap direct feedback is implemented inside the CML slicers to relax the critical timing of DFE and maximize the achievable data-rate. In addition to the per-slice main 3 data samplers, an error sampler is utilized for background threshold control and an edge-based sampler performs both PLL-based CDR phase detection and generates information for background DFE tap adaptation. The receiver consumes 4.63mW/Gb/s and compensates for up to 20.8dB loss when operated with a 2- tap FFE transmitter. The experimental results and comparison with state-of-the-art shows superior power efficiency of the presented prototypes for similar data-rate and channel loss. The usage of proposed design techniques are not limited to these specific prototypes and can be applied for any wireline transceiver with different modulation, data-rate and CMOS technology

    Design Techniques for High Performance Serial Link Transceivers

    Get PDF
    Increasing data rates over electrical channels with significant frequency-dependent loss is difficult due to excessive inter-symbol interference (ISI). In order to achieve sufficient link margins at high rates, I/O system designers implement equalization in the transmitters and are motivated to consider more spectrally-efficient modulation formats relative to the common PAM-2 scheme, such as PAM-4 and duobinary. The first work, reviews when to consider PAM-4 and duobinary formats, as the modulation scheme which yields the highest system margins at a given data rate is a function of the channel loss profile, and presents a 20Gb/s triple-mode transmitter capable of efficiently implementing these three modulation schemes and three-tap feedforward equalization. A statistical link modeling tool, which models ISI, crosstalk, random noise, and timing jitter, is developed to compare the three common modulation formats operating on electrical backplane channel models. In order to improve duobinary modulation efficiency, a low-power quarter-rate duobinary precoder circuit is proposed which provides significant timing margin improvement relative to full-rate precoders. Also as serial I/O data rates scale above 10 Gb/s, crosstalk between neighboring channels degrades system bit-error rate (BER) performance. The next work presents receive-side circuitry which merges the cancellation of both near-end and far-end crosstalk (NEXT/FEXT) and can automatically adapt to different channel environments and variations in process, voltage, and temperature. NEXT cancellation is realized with a novel 3-tap FIR filter which combines two traditional FIR filter taps and a continuous-time band-pass filter IIR tap for efficient crosstalk cancellation, with all filter tap coefficients automatically determined via an ondie sign-sign least-mean-square (SS-LMS) adaptation engine. FEXT cancellation is realized by coupling the aggressor signal through a differentiator circuit whose gain is automatically adjusted with a power-detection-based adaptation loop. In conclusion, the proposed architectures in the transmitter side and receiver side together are to be good solution in the high speed I/O serial links to improve the performance by overcome the physical channel loss and adjacent channel noise as the system becomes complicated

    Bandwidth Compressed Waveform and System Design for Wireless and Optical Communications: Theory and Practice

    Get PDF
    This thesis addresses theoretical and practical challenges of spectrally efficient frequency division multiplexing (SEFDM) systems in both wireless and optical domains. SEFDM improves spectral efficiency relative to the well-known orthogonal frequency division multiplexing (OFDM) by non-orthogonally multiplexing overlapped sub-carriers. However, the deliberate violation of orthogonality results in inter carrier interference (ICI) and associated detection complexity, thus posing many challenges to practical implementations. This thesis will present solutions for these issues. The thesis commences with the fundamentals by presenting the existing challenges of SEFDM, which are subsequently solved by proposed transceivers. An iterative detection (ID) detector iteratively removes self-created ICI. Following that, a hybrid ID together with fixed sphere decoding (FSD) shows an optimised performance/complexity trade-off. A complexity reduced Block-SEFDM can subdivide the signal detection into several blocks. Finally, a coded Turbo-SEFDM is proved to be an efficient technique that is compatible with the existing mobile standards. The thesis also reports the design and development of wireless and optical practical systems. In the optical domain, given the same spectral efficiency, a low-order modulation scheme is proved to have a better bit error rate (BER) performance when replacing a higher order one. In the wireless domain, an experimental testbed utilizing the LTE-Advanced carrier aggregation (CA) with SEFDM is operated in a realistic radio frequency (RF) environment. Experimental results show that 40% higher data rate can be achieved without extra spectrum occupation. Additionally, a new waveform, termed Nyquist-SEFDM, which compresses bandwidth and suppresses out-of-band power leakage is investigated. A 4th generation (4G) and 5th generation (5G) coexistence experiment is followed to verify its feasibility. Furthermore, a 60 GHz SEFDM testbed is designed and built in a point-to-point indoor fiber wireless experiment showing 67% data rate improvement compared to OFDM. Finally, to meet the requirements of future networks, two simplified SEFDM transceivers are designed together with application scenarios and experimental verifications
    • …
    corecore