Robust Vehicular Communications for Traffic Safety---Channel Estimation and Multiantenna Schemes

Vehicular communications, where vehicles exchange information with other vehicles or entities in the road traffic environment, is expected to be a part of the future transportation system and promises to support a plethora of applications for traffic safety and efficiency. In particular, vehicle-to-vehicle (V2V) communication promises to support numerous traffic safety applications by enabling a vehicle to broadcast its current status to all the other vehicles in its surrounding.\ua0 \ua0 Vehicular wireless channels can be highly time- and/or frequency-selective due to high mobility of the vehicles and/or large delay spreads. IEEE 802.11p has been specified as the physical layer standard for vehicular communications, where the pilots are densely concentrated at the beginning of a frame. As a consequence, accurate channel estimation in later parts of the frame becomes a challenging task. In this thesis, a solution to overcome the ill-suited pilot pattern is studied; a cross-layered scheme to insert complementary pilots into an 802.11p frame is proposed. The scheme does not require modifications to the 802.11p standard and a modified receiver can utilize the complementary pilots for accurate channel estimation in vehicular channels.\ua0 \ua0 The metallic components of present-day vehicles pose a challenge in designing antenna systems that satisfy a minimum required directive gain in the entire horizontal plane. Multiple antennas with contrasting directive gain patterns can be used to alleviate the problems due to low directive gains. A scheme that combines the output of L antennas to the input of a single-port receiver is proposed in the thesis. The combining scheme is designed to minimize the probability of a burst error, i.e., an unsuccessful decoding of K consecutive packets from a transmitter arriving in the direction of low directive gains of the individual antennas. To minimize complexity, the scheme does not estimate or use any channel state information. It is shown using measured and simulated directive gain patterns that the probability of burst errors for packets arriving in the direction of low directive gains of the individual antenna elements can be minimized.\ua0 \ua0 The enhanced distributed channel access (EDCA) scheme is used in V2V communications to facilitate the sharing of allocated time-frequency resources. The packet success ratio (PSR) of the broadcast messages in the EDCA scheme depends on the number of vehicles and the packet transmission rate. The interference at a receiving vehicle increases due to multiple simultaneous transmissions when the number of vehicles grows beyond a limit, resulting in the decrease of the PSR. A receiver setup with sector antennas, where the output of each antenna can be processed separately to decode a packet, is described in the thesis with a detailed performance analysis. A significant increase in the PSR is shown in a dense vehicular scenario by using four partially overlapping sector antennas compared with a single omnidirectional antenna setup

Safety Applications and Measurement Tools for Connected Vehicles

L'abstract è presente nell'allegato / the abstract is in the attachmen

Advanced Applications of Rapid Prototyping Technology in Modern Engineering

Rapid prototyping (RP) technology has been widely known and appreciated due to its flexible and customized manufacturing capabilities. The widely studied RP techniques include stereolithography apparatus (SLA), selective laser sintering (SLS), three-dimensional printing (3DP), fused deposition modeling (FDM), 3D plotting, solid ground curing (SGC), multiphase jet solidification (MJS), laminated object manufacturing (LOM). Different techniques are associated with different materials and/or processing principles and thus are devoted to specific applications. RP technology has no longer been only for prototype building rather has been extended for real industrial manufacturing solutions. Today, the RP technology has contributed to almost all engineering areas that include mechanical, materials, industrial, aerospace, electrical and most recently biomedical engineering. This book aims to present the advanced development of RP technologies in various engineering areas as the solutions to the real world engineering problems

Investigation of Vehicle-to-Everything (V2X) Communication for Autonomous Control of Connected Vehicles

Autonomous Driving Vehicles (ADVs) has received considerable attention in recent years by academia and industry, bringing about a paradigm shift in Intelligent Transportation Systems (ITS), where vehicles operate in close proximity through wireless communication. It is envisioned as a promising technology for realising efficient and intelligent transportation systems, with potential applications for civilian and military purposes. Vehicular network management for ADVs is challenging as it demands mobility, location awareness, high reliability, and low latency data traffic. This research aims to develop and implement vehicular communication in conjunction with a driving algorithm for ADVs feedback control system with a specific focus on the safe displacement of vehicle platoon while sensing the surrounding environment, such as detecting road signs and communicate with other road users such as pedestrian, motorbikes, non-motorised vehicles and infrastructure. However, in order to do so, one must investigate crucial aspects related to the available technology, such as driving behaviour, low latency communication requirement, communication standards, and the reliability of such a mechanism to decrease the number of traffic accidents and casualties significantly. To understand the behaviour of wireless communication compared to the theoretical data rates, throughput, and roaming behaviour in a congested indoor line-of-sight heterogeneous environment, we first carried out an experimental study for IEEE 802.11a, 802.11n and 802.11ac standards in a 5 GHz frequency spectrum. We validated the results with an analytical path loss model as it is essential to understand how the client device roams or decides to roam from one Access Point to another and vice-versa. We observed seamless roaming between the tested protocols irrespective of their operational environment (indoor or outdoor); their throughput efficiency and data rate were also improved by 8-12% when configured with Short Guard Interval (SGI) of 400ns compared to the theoretical specification of the tested protocols. Moreover, we also investigated the Software-Defined Networking (SDN) for vehicular communication and compared it with the traditional network, which is generally incorporated vertically where control and data planes are bundled collectively. The SDN helped gain more flexibility to support multiple core networks for vehicular communication and tackle the potential challenges of network scalability for vehicular applications raised by the ADVs. In particular, we demonstrate that the SDN improves throughput efficiency by 4% compared to the traditional network while ensuring efficient bandwidth and resource management. Finally, we proposed a novel data-driven coordination model which incorporates Vehicle-to-Everything (V2X) communication and Intelligent Driver Model (IDM), together called V2X Enabled Intelligent Driver Model (VX-IDM). Our model incorporates a Car-Following Model (CFM), i.e., IDM, to model a vehicle platoon in an urban and highway traffic scenario while ensuring the vehicle platoon's safety with the integration of IEEE 802.11p Vehicle-to-Infrastructure (V2I) communication scheme. The model integrates the 802.11p V2I communication channel with the IDM in MATLAB using ODE‐45 and utilises the 802.11p simulation toolbox for configuring vehicular channels. To demonstrate model functionality in urban and highway traffic environments, we developed six case studies. We also addressed the heterogeneity issue of wireless networks to improve the overall network reliability and efficiency by estimating the Signal-to-Noise Ratio (SNR) parameters for the platoon vehicle's displacement and location on the road from Road-Side-Units (RSUs). The simulation results showed that inter-vehicle spacing could be steadily maintained at a minimum safe value at all the time. Moreover, the model has a fault-tolerant mechanism that works even when communication with infrastructure is interrupted or unavailable, making the VX-IDM model collision-free

Cooperative Radio Communications for Green Smart Environments

The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin

A channel model and coding for vehicle to vehicle communication based on a developed V-SCME

Over the recent years, VANET communication has attracted a lot of attention due to its potential in facilitating the implementation of 'Intelligent Transport System'. Vehicular applications need to be completely tested before deploying them in the real world. In this context, VANET simulations would be preferred in order to evaluate and validate the proposed model, these simulations are considered inexpensive compared to the real world (hardware) tests. The development of a more realistic simulation environment for VANET is critical in ensuring high performance. Any environment required for simulating VANET, needs to be more realistic and include a precise representation of vehicle movements, as well as passing signals among different vehicles. In order to achieve efficient results that reflect the reality, a high computational power during the simulation is needed which consumes a lot of time. The existing simulation tools could not simulate the exact physical conditions of the real world, so results can be viewed as unsatisfactory when compared with real world experiments. This thesis describes two approaches to improve such vehicle to vehicle communication. The first one is based on the development of an already existing approach, the Spatial Channel Model Extended (SCME) for cellular communication which is a verified, validated and well-established communication channel model. The new developed model, is called Vehicular - Spatial Channel Model Extended (V-SCME) and can be utilised for Vehicle to Vehicle communication. V-SCME is a statistical channel model which was specifically developed and configured to satisfy the requirements of the highly dynamic network topology such as vehicle to vehicle communication. V-SCME provides a precise channel coefficients library for vehicle to vehicle communication for use by the research community, so as to reduce the overall simulation time. The second approach is to apply V-BLAST (MIMO) coding which can be implemented with vehicle to vehicle communication and improve its performance over the V-SCME. The V- SCME channel model with V-BLAST coding system was used to improve vehicle to vehicle physical layer performance, which is a novel contribution. Based on analysis and simulations, it was found that the developed channel model V-SCME is a good solution to satisfy the requirements of vehicle to vehicle communication, where it has considered a lot of parameters in order to obtain more realistic results compared with the real world tests. In addition, V-BLAST (MIMO) coding with the V-SCME has shown an improvement in the bit error rate. The obtained results were intensively compared with other types of MIMO coding

A comprehensive survey of V2X cybersecurity mechanisms and future research paths

Recent advancements in vehicle-to-everything (V2X) communication have notably improved existing transport systems by enabling increased connectivity and driving autonomy levels. The remarkable benefits of V2X connectivity come inadvertently with challenges which involve security vulnerabilities and breaches. Addressing security concerns is essential for seamless and safe operation of mission-critical V2X use cases. This paper surveys current literature on V2X security and provides a systematic and comprehensive review of the most relevant security enhancements to date. An in-depth classification of V2X attacks is first performed according to key security and privacy requirements. Our methodology resumes with a taxonomy of security mechanisms based on their proactive/reactive defensive approach, which helps identify strengths and limitations of state-of-the-art countermeasures for V2X attacks. In addition, this paper delves into the potential of emerging security approaches leveraging artificial intelligence tools to meet security objectives. Promising data-driven solutions tailored to tackle security, privacy and trust issues are thoroughly discussed along with new threat vectors introduced inevitably by these enablers. The lessons learned from the detailed review of existing works are also compiled and highlighted. We conclude this survey with a structured synthesis of open challenges and future research directions to foster contributions in this prominent field.This work is supported by the H2020-INSPIRE-5Gplus project (under Grant agreement No. 871808), the ”Ministerio de Asuntos Económicos y Transformacion Digital” and the European Union-NextGenerationEU in the frameworks of the ”Plan de Recuperación, Transformación y Resiliencia” and of the ”Mecanismo de Recuperación y Resiliencia” under references TSI-063000-2021-39/40/41, and the CHIST-ERA-17-BDSI-003 FIREMAN project funded by the Spanish National Foundation (Grant PCI2019-103780).Peer ReviewedPostprint (published version