Implementation of a 200 MSps 12-bit SAR ADC

Analog-to-digital converters (ADCs) with high conversion frequency, often based on pipelined architectures, are used for measuring instruments, wireless communication and video applications. Successive approximation register (SAR) converters offer a compact and power efficient alternative but the conversion speed is typically designed for lower frequencies. In this thesis a low-power 12-bit 200 MSps SAR ADC based on charge redistribution was designed for a 28 nm CMOS technology. The proposed design uses an efficient SAR algorithm (merged capacitor switching procedure) to reduce power consumption due to capacitor charging by 88 % compared to a conventional design, as well as reducing the total capacitor area by half. Sampling switches were bootstrapped for increased linearity compared to simple transmission gates. Another feature of the low power design is a fully-dynamic comparator which does not require a preamplifier. Pre-layout simulations of the SAR ADC with 800 MHz input frequency shows an SNDR of 64.8 dB, corresponding to an ENOB of 10.5, and an SFDR of 75.3 dB. The total power consumption is 1.77 mW with an estimated value of 500 W for the unimplemented digital logic. Calculation of the Schreier figure-of-merit was done with an input signal at the Nyquist frequency. The simulated SNDR, SFDR and power equals 69.5 dB, 77.3 dB and 1.9 mW respectively, corresponding to a figure-of merit of 176.6 dB.Från analogt till digitalt - snabba och strömsnåla omvandlare Dagens digitala samhälle ställer höga krav på prestanda och effektivitet. I samarbete med Ericsson i Lund har en krets för signalomvandling utvecklats. Genom smart design uppnås hög hastighet och låg strömförbrukning som ligger i forskningens framkant. Från analogt till digitalt Ett viktigt byggblock för telekommunikation och videoapplikationer är så kallade A/D-omvandlare, som översätter mellan analoga signaler (till exempel ljud) och digitala signaler bestående av ettor och nollor. En väldigt effektiv metod för A/D-omvandling bygger på så kallad successiv approximation. Metoden innebär att signalen som ska omvandlas jämförs med en referensnivå, som stegvis justeras för att närma sig signalens värde. Till slut har man en tillräckligt god uppskattning av värdet som ska mätas. Just en sådan omvandlare har utvecklats med höga krav på hastighet och energiförbrukning. Detta gjordes genom datorsimuleringar av modeller som beskriver kretsen. Referensnivån skapas ofta genom att styra ett nätverk som lagrar elektrisk laddning. Omvandlingens noggrannhet, eller upplösning, beror på hur många nivåer som finns tillgängliga det vill säga hur nära signalens värde man kan komma. I den designade kretsen finns hela 4096 nivåer! Det finns många källor till osäkerhet i systemet, bland annat hur exakta referensnivåerna är och hur bra jämförelsen med insignalen kan göras. Eftersom dessa eventuellt kan leda till en försämring av omvandlingens noggrannhet måste alla delar i kretsen utformas med detta i åtanke. Höga hastigheter Eftersom det krävs många steg för referensnivån att närma sig signalens värde är den maximala omvandlingshastigheten ofta begränsad. Med teknikens utveckling öppnas nya möjligheter i takt med att mikrochippens enskilda komponenter blir snabbare. Modern forskning visar att omvandlare baserade på successiv approximation kan uppnå hastigheter på flera miljoner mätvärden varje sekund, vilket även den utvecklade kretsen klarar av. Effektiv design Nya metoder för successiv approximation möjliggör stora besparingar när det gäller effektförbrukning, till exempel genom att effektivisera upp- och urladdningen av nätverket. Genom små ändringar kunde nätverkets energiförbrukning minskas med över 90 % samtidigt som dess area halverades. Eftersom produktionskostnaden för integrerade kretsar är hög medför varje minskning av kretsens area att kostnaden sjunker

Direct sampling receivers for broadband communications

Today everything tends to be connected in the Internet of Things (IoT) universe, where a broad variety of communication standards and technologies are used for those connected devices. It is always a dream to design a Software-Defined Radio (SDR) supporting different standards solely based on the software configuration. As integrated-circuit (IC) manufacture and design advance, a partial of SDR can be realized. This thesis investigates one of the most important parts in a SDR: the analog design of a direct sampling (DS) receiver, which mainly consists of a broadband RF front end and a wideband ADC. Especially, a DS receiver shows a great flexibility and efficiency for the simultaneous reception of multiple channels comparing with the traditional parallelism of superheterodyne structure. The research contributions of this work include (1) demonstration and comparative analysis of two new architectures of broadband RFPGAs: voltage-mode: RFPGA-V and current-mode: RFPGA-I. RFPGA-V and RFPGA-I utilize an innovative interpolation method and current steering approach, respectively, to achieve a fine gain step of 0.25-dB over 40-dB gain range for several GHz frequency range. Besides, with innovative design, no off-chip inductor is needed for the both RFPGAs. (2) The design of a 5-GS/s 10b time-interleaved SAR. The ADC power efficiency is significantly improved by many design techniques: the low-energy CDAC switching scheme, optimized input common-mode voltage for comparator, optimal reduced radix-2 capacitor ratio for low-power reference buffers and higher conversion speed, etc. The lane-to-lane mismatches in a time-interleave ADC are minimized by using optimal floor plan and then are calibrated digitally. Three prototypes: the broadband RF front ends with RFPGA-V, the broadband RF front ends with RFPGA-I and a 5-GHz ADC, are fabricated to verify the proposed ideas in 28nm CMOS technology.Electrical and Computer Engineerin

Design of Power Management Integrated Circuits and High-Performance ADCs

A battery-powered system has widely expanded its applications to implantable medical devices (IMDs) and portable electronic devices. Since portable devices or IMDs operate in the energy-constrained environment, their low-power operations in combination with efficiently sourcing energy to them are key problems to extend device life. This research proposes novel circuit techniques for two essential functions of a power receiving unit (PRU) in the energy-constrained environment, which are power management and signal processing. The first part of this dissertation discusses power management integrated circuits for a PRU. From a power management perspective, the most critical two circuit blocks are a front-end rectifier and a battery charger. The front-end CMOS active rectifier converts transmitted AC power into DC power. High power conversion efficiency (PCE) is required to reduce power loss during the power transfer, and high voltage conversion ratio (VCR) is required for the rectifier to enable low-voltage operations. The proposed 13.56-MHz CMOS active rectifier presents low-power circuit techniques for comparators and controllers to reduce increasing power loss of an active diode with offset/delay calibration. It is implemented with 5-V devices of a 0.35 µm CMOS process to support high voltage. A peak PCE of 89.0%, a peak VCR of 90.1%, and a maximum output power of 126.7 mW are measured for 200Ω loading. The linear battery charger stores the converted DC power into a battery. Since even small power saving can be enough to run the low-power PRU, a battery charger with low IvQ is desirable. The presented battery charger is based on a single amplifier for regulation and the charging phase transition from the constant-current (CC) phase to the constant-voltage (CV) phase. The proposed unified amplifier is based on stacked differential pairs which share the bias current. Its current-steering property removes multiple amplifiers for regulation and the CC-CV transition, and achieves high unity-gain loop bandwidth for fast regulation. The charger with the maximum charging current of 25 mA is implemented in 0.35 µm CMOS. A peak charger efficiency of 94% and average charger efficiency of 88% are achieved with an 80-mAh Li-ion polymer battery. The second part of this dissertation focuses on analog-to-digital converters (ADCs). From a signal processing perspective, an ADC is one of the most important circuit blocks in the PRU. Hence, an energy-efficient ADC is essential in the energy-constrained environment. A pipelined successive approximation register (SAR) ADC has good energy efficiency in a design space of moderate-to-high speeds and resolutions. Process-Voltage-Temperature variations of a dynamic amplifier in the pipelined-SAR ADC is a key design issue. This research presents two dynamic amplifier architectures for temperature compensation. One is based on a voltage-to-time converter (VTC) and a time-to-voltage converter (TVC), and the other is based on a temperature-dependent common-mode detector. The former amplifier is adopted in a 13-bit 10-50 MS/s subranging pipelined-SAR ADC fabricated in 0.13-µm CMOS. The ADC can operate under the power supply voltage of 0.8-1.2 V. Figure-of-Merits (FoMs) of 4-11.3 fJ/conversion-step are achieved. The latter amplifier is also implemented in 0.13-µm CMOS, consuming 0.11 mW at 50 MS/s. Its measured gain variation is 2.1% across the temperature range of -20°C to 85 °C

Multi-Stage Noise-Shaping Continuous-Time Sigma-Delta Modulator

The design of a single-loop continuous-time ∑∆ modulator (CT∑∆M) with high resolution, wide bandwidth, and low power consumption is very challenging. The multi-stage noise-shaping (MASH) CT∑∆M architecture is identified as an advancement to the single-loop CT∑∆M architecture in order to satisfy the ever stringent requirements of next generation wireless systems. However, it suffers from the problems of quantization noise leakage and non-ideal interstage interfacing which hinder its widespread adoption. To solve these issues, this dissertation proposes a MASH CT∑∆M with on-chip RC time constant calibration circuits, multiple feedforward interstage paths, and a fully integrated noise cancellation filter (NCF). The prototype core modulator architecture is a cascade of two single-loop second- order CT∑∆M stages, each of which consists of an integrator-based active-RC loop filter, current-steering feedback digital-to-analog converters, and a four-bit flash quantizer. On-chip RC time constant calibration circuits and high gain multi-stage operational amplifiers are realized to mitigate quantization noise leakage due to process variation. Multiple feedforward interstage paths are introduced to (i) synthesize a fourth-order noise transfer function with DC zeros, (ii) simplify the design of NCF, and (iii) reduce signal swings at the second-stage integrator outputs. Fully integrated in 40 nm CMOS, the prototype chip achieves 74.4 dB of signal-to-noise and distortion ratio (SNDR), 75.8 dB of signal-to-noise ratio, and 76.8 dB of dynamic range in 50.3 MHz of bandwidth (BW) at 1 GHz of sampling frequency with 43.0 mW of power consumption (P). It does not require external software calibration and possesses minimal out-of-band signal transfer function peaking. The figure-of-merit (FOM), defined as FOM = SNDR + 10 log10(BW/P), is 165.1 dB

Design of sigma-delta modulators for analog-to-digital conversion intensively using passive circuits

This thesis presents the analysis, design implementation and experimental evaluation of passiveactive discrete-time and continuous-time Sigma-Delta (ΣΔ) modulators (ΣΔMs) analog-todigital converters (ADCs). Two prototype circuits were manufactured. The first one, a discrete-time 2nd-order ΣΔM, was designed in a 130 nm CMOS technology. This prototype confirmed the validity of the ultra incomplete settling (UIS) concept used for implementing the passive integrators. This circuit, clocked at 100 MHz and consuming 298 μW, achieves DR/SNR/SNDR of 78.2/73.9/72.8 dB, respectively, for a signal bandwidth of 300 kHz. This results in a Walden FoMW of 139.3 fJ/conv.-step and Schreier FoMS of 168 dB. The final prototype circuit is a highly area and power efficient ΣΔM using a combination of a cascaded topology, a continuous-time RC loop filter and switched-capacitor feedback paths. The modulator requires only two low gain stages that are based on differential pairs. A systematic design methodology based on genetic algorithm, was used, which allowed decreasing the circuit’s sensitivity to the circuit components’ variations. This continuous-time, 2-1 MASH ΣΔM has been designed in a 65 nm CMOS technology and it occupies an area of just 0.027 mm2. Measurement results show that this modulator achieves a peak SNR/SNDR of 76/72.2 dB and DR of 77dB for an input signal bandwidth of 10 MHz, while dissipating 1.57 mW from a 1 V power supply voltage. The ΣΔM achieves a Walden FoMW of 23.6 fJ/level and a Schreier FoMS of 175 dB. The innovations proposed in this circuit result, both, in the reduction of the power consumption and of the chip size. To the best of the author’s knowledge the circuit achieves the lowest Walden FOMW for ΣΔMs operating at signal bandwidth from 5 MHz to 50 MHz reported to date

Digital Intensive Mixed Signal Circuits with In-situ Performance Monitors

University of Minnesota Ph.D. dissertation.November 2016. Major: Electrical/Computer Engineering. Advisor: Chris Kim. 1 computer file (PDF); x, 137 pages.Digital intensive circuit design techniques of different mixed-signal systems such as data converters, clock generators, voltage regulators etc. are gaining attention for the implementation of modern microprocessors and system-on-chips (SoCs) in order to fully utilize the benefits of CMOS technology scaling. Moreover different performance improvement schemes, for example, noise reduction, spur cancellation, linearity improvement etc. can be easily performed in digital domain. In addition to that, increasing speed and complexity of modern SoCs necessitate the requirement of in-situ measurement schemes, primarily for high volume testing. In-situ measurements not only obviate the need for expensive measurement equipments and probing techniques, but also reduce the test time significantly when a large number of chips are required to be tested. Several digital intensive circuit design techniques are proposed in this dissertation along with different in-situ performance monitors for a variety of mixed signal systems. First, a novel beat frequency quantization technique is proposed in a two-step VCO quantizer based ADC implementation for direct digital conversion of low amplitude bio- potential signals. By direct conversion, it alleviates the requirement of the area and power consuming analog-frontend (AFE) used in a conventional ADC designs. This prototype design is realized in a 65nm CMOS technology. Measured SNDR is 44.5dB from a 10mVpp, 300Hz signal and power consumption is only 38μW. Next, three different clock generation circuits, a phase-locked loop (PLL), a multiplying delay-locked loop (MDLL) and a frequency-locked loop (FLL) are presented. First a 0.4-to-1.6GHz sub-sampling fractional-N all digital PLL architecture is discussed that utilizes a D-flip-flop as a digital sub-sampler. Measurement results from a 65nm CMOS test-chip shows 5dB lower phase noise at 100KHz offset frequency, compared to a conventional architecture. The Digital PLL (DPLL) architecture is further extended for a digital MDLL implementation in order to suppress the VCO phase noise beyond the DPLL bandwidth. A zero-offset aperture phase detector (APD) and a digital- to-time converter (DTC) are employed for static phase-offset (SPO) cancellation. A unique in-situ detection circuitry achieves a high resolution SPO measurement in time domain. A 65nm test-chip shows 0.2-to-1.45GHz output frequency range while reducing the phase-noise by 9dB compared to a DPLL. Next, a frequency-to-current converter (FTC) based fractional FLL is proposed for a low accuracy clock generation in an extremely low area for IoT application. High density deep-trench capacitors are used for area reduction. The test-chip is fabricated in a 32nm SOI technology that takes only 0.0054mm2 active area. A high-resolution in-situ period jitter measurement block is also incorporated in this design. Finally, a time based digital low dropout (DLDO) regulator architecture is proposed for fine grain power delivery over a wide load current dynamic range and input/output voltage in order to facilitate dynamic voltage and frequency scaling (DVFS). High- resolution beat frequency detector dynamically adjusts the loop sampling frequency for ripple and settling time reduction due to load transients. A fixed steady-state voltage offset provides inherent active voltage positioning (AVP) for ripple reduction. Circuit simulations in a 65nm technology show more than 90% current efficiency for 100X load current variation, while it can operate for an input voltage range of 0.6V – 1.2V