Generating All Two-MOS-Transistor Amplifiers Leads to New Wide-Band LNAs

This paper presents a methodology that systematically generates all 2-MOS-transistor wide-band amplifiers, assuming that MOSFET is exploited as a voltage-controlled current source. This leads to new circuits. Their gain and noise factor have been compared to well-known wide-band amplifiers. One of the new circuits appears to have a relatively low noise factor, which is also gain independent. Based on this new circuit, a 50-900 MHz variable-gain wide-band LNA has been designed in 0.35-µm CMOS. Measurements show a noise figure between 4.3 and 4.9 dB for gains from 6 to 11 dB. These values are more than 2 dB lower than the noise figure of the wide-band common-gate LNA for the same input matching, power consumption, and voltage gain. IIP2 and IIP3 are better than 23.5 and 14.5 dBm, respectively, while the LNA drains only 1.5 mA at 3.3 V

Systematic Comparison of HF CMOS Transconductors

Transconductors are commonly used as active elements in high-frequency (HF) filters, amplifiers, mixers, and oscillators. This paper reviews transconductor design by focusing on the V-I kernel that determines the key transconductor properties. Based on bandwidth considerations, simple V-I kernels with few or no internal nodes are preferred. In a systematic way, virtually all simple kernels published in literature are generated. This is done in two steps: 1) basic 3-terminal transconductors are covered and 2) then five different techniques to combine two of them in a composite V-I kernel. In order to compare transconductors in a fair way, a normalized signal-to-noise ratio (NSNR) is defined. The basic V-I kernels and the five classes of composite V-I kernels are then compared, leading to insight in the key mechanisms that affect NSNR. Symbolic equations are derived to estimate NSNR, while simulations with more advanced MOSFET models verify the results. The results show a strong tradeoff between NSNR and transconductance tuning range. Resistively generated MOSFETs render the best NSNR results and are robust for future technology developments

Small-signal model for 2D-material based field-effect transistors targeting radio-frequency applications: the importance of considering non-reciprocal capacitances

A small-signal equivalent circuit of 2D-material based field-effect transistors is presented. Charge conservation and non-reciprocal capacitances have been assumed so the model can be used to make reliable predictions at both device and circuit levels. In this context, explicit and exact analytical expressions of the main radio-frequency figures of merit of these devices are given. Moreover, a direct parameter extraction methodology is provided based on S-parameter measurements. In addition to the intrinsic capacitances, transconductance and output conductance, our approach allows extracting the series combination of drain/source metal contact and access resistances. Accounting for these extrinsic resistances is of upmost importance when dealing with low dimensional field-effect transistors.Comment: 8 pages, 10 figures, 4 table

Proceedings of the Cold Electronics Workshop

The benefits and problems of the use of cold semiconductor electronics and the research and development effort required to bring cold electronics into more widespread use were examined

Thermal Noise Canceling in LNAs: A Review

Most wide-band amplifiers suffer from a fundamental trade-off between noise figure NF and source impedance matching, which limits NF to values typically above 3dB. Recently, a feed-forward noise canceling technique has been proposed to break this trade-off. This paper reviews the principle of the technique and its key properties. Although the technique has been applied to wideband CMOS LNAs, it can just as well be implemented exploiting transconductance elements realized with other types of transistors

Next generation RFID telemetry design for biomedical implants.

The design and development of a Radio Frequency Identification (RFID) based pressure-sensing system to increase the range of current Intra-Ocular Pressure (IOP) sensing systems is described in this dissertation. A large number of current systems use near-field inductive coupling for the transfer of energy and data, which limits the operational range to only a few centimeters and does not allow for continuous monitoring of pressure. Increasing the powering range of the telemetry system will offer the possibility of continuous monitoring since the reader can be attached to a waist belt or put on a night stand when sleeping. The system developed as part of this research operates at Ultra-High Frequencies (UHF) and makes use of the electromagnetic far field to transfer energy and data, which increases the potential range of operation and allows for the use of smaller antennas. The system uses a novel electrically small antenna (ESA) to receive the incident RF signal. A four stage Schottky circuit rectifies and multiplies the received RF signal and provides DC power to a Colpitts oscillator. The oscillator is connected to a pressure sensor and provides an output signal frequency that is proportional to the change in pressure. The system was fabricated using a mature, inexpensive process. The performance of the system compares well with current state of the art, but uses a smaller antenna and a less expensive fabrication process. The system was able to operate over the desired range of 1 m using a half-wave dipole antenna. It was possible to power the system over a range of at least 6.4 cm when the electrically small antenna was used as the receiving antenna

DESIGN OF LOW POWER MOBILE TRANSMITTER

The objective of this project is to design a power amplifier for a new two way mobile radio product being launched by Motorola. Two-way mobile radio consists of a transmitter, receiver and a voltage-controlled oscillator. Mobile radios usually have transmitter whose power output ranges from 1 W to 50 W. Design of transmitter lineup for mobile radio involves the design of appropriate matching network for driver and power amplifier. The power and voltage control of these devices are equally important. Designing a mobile radio transmitter is regarded tricky due to difficulty in getting a robust transmitter that is stable with minimum oscillation. In this work, the design is attempted usmg Advanced Design Simulator (ADS). The design simulation provides accurate simulation on harmonic filter and antenna switch. 50 ohm matching networks have also been designed and simulated using ADS and it gives close approximation to the specifications. The radio has since been prototyped and tested. The evaluation and testing of the radio has been carried out and it satisfies the specifications that are set by the Telecommunication Industry Association (TIA). Some minor optimization has also been performed to improve the radio performance. Eventual product is a transmitter line up that function well today. 11

The Characterization of Effective Electromagnetic Fields on the Safety and Quality of Low-Moisture Foods (EFFS) - Prototype Device Development

Contamination of low-moisture foods including flour, wheat grain, baby formula, and more, have increasingly become a concern due to sanitizing challenges. While industrial food processors have long used RF heating to sanitize mass quantities, an equivalent consumer device is absent from the market today. The Characterization of Effective Electromagnetic Fields on the Safety and Quality of Low-Moisture Foods (EEFS) project is an interdisciplinary effort to develop an RF heating consumer device to sanitize low-moisture foods. A prototype device was designed to sanitize low-moisture food items using RF heating acceptable for commercial or consumer applications