Cooperative network-coding system for wireless sensor networks

Describes a cooperative network coding system for wireless sensor networks. In this paper, we propose two practical power) and bandwidth)efficient systems based on amplify)and)forward (AF) and decode)and)forward (DF) schemes to address the problem of information exchange via a relay. The key idea is to channel encode each source’s message by using a high)performance non)binary turbo code based on Partial Unit Memory (PUM) codes to enhance the bit)error)rate performance, then reduce the energy consumption and increase spectrum efficiency by using network coding (NC) to combine individual nodes’ messages at the relay before forwarding to the destination. Two simple and low complexity physical layer NC schemes are proposed based on combinations of received source messages at the relay. We also present the theoretical limits and numerical analysis of the proposed schemes. Simulation results under Additive White Gaussian Noise, confirm that the proposed schemes achieve significant bandwidth savings and fewer transmissions over the benchmark systems which do not resort to NC. Theoretical limits for capacity and Signal to Noise Ratio behaviour for the proposed schemes are derived. The paper also proposes a cooperative strategy that is useful when insufficient combined messages are received at a node to recover the desired source messages, thus enabling the system to retrieve all packets with significantly fewer retransmission request messages

A Mobile Satellite Experiment (MSAT-X) network definition

The network architecture development of the Mobile Satellite Experiment (MSAT-X) project for the past few years is described. The results and findings of the network research activities carried out under the MSAT-X project are summarized. A framework is presented upon which the Mobile Satellite Systems (MSSs) operator can design a commercial network. A sample network configuration and its capability are also included under the projected scenario. The Communication Interconnection aspect of the MSAT-X network is discussed. In the MSAT-X network structure two basic protocols are presented: the channel access protocol, and the link connection protocol. The error-control techniques used in the MSAT-X project and the packet structure are also discussed. A description of two testbeds developed for experimentally simulating the channel access protocol and link control protocol, respectively, is presented. A sample network configuration and some future network activities of the MSAT-X project are also presented

Wireless Sensor Networking in Challenging Environments

Recent years have witnessed growing interest in deploying wireless sensing applications in real-world environments. For example, home automation systems provide fine-grained metering and control of home appliances in residential settings. Similarly, assisted living applications employ wireless sensors to provide continuous health and wellness monitoring in homes. However, real deployments of Wireless Sensor Networks (WSNs) pose significant challenges due to their low-power radios and uncontrolled ambient environments. Our empirical study in over 15 real-world apartments shows that low-power WSNs based on the IEEE 802.15.4 standard are highly susceptible to external interference beyond user control, such as Wi-Fi access points, Bluetooth peripherals, cordless phones, and numerous other devices prevalent in residential environments that share the unlicensed 2.4 GHz ISM band with IEEE 802.15.4 radios. To address these real-world challenges, we developed two practical wireless network protocols including the Adaptive and Robust Channel Hopping (ARCH) protocol and the Adaptive Energy Detection Protocol (AEDP). ARCH enhances network reliability through opportunistically changing radio\u27s frequency to avoid interference and environmental noise and AEDP reduces false wakeups in noisy wireless environments by dynamically adjusting the wakeup threshold of low-power radios. Another major trend in WSNs is the convergence with smart phones. To deal with the dynamic wireless conditions and varying application requirements of mobile users, we developed the Self-Adapting MAC Layer (SAML) to support adaptive communication between smart phones and wireless sensors. SAML dynamically selects and switches Medium Access Control protocols to accommodate changes in ambient conditions and application requirements. Compared with the residential and personal wireless systems, industrial applications pose unique challenges due to their critical demands on reliability and real-time performance. We developed an experimental testbed by realizing key network mechanisms of industrial Wireless Sensor and Actuator Networks (WSANs) and conducted an empirical study that revealed the limitations and potential enhancements of those mechanisms. Our study shows that graph routing is more resilient to interference and its backup routes may be heavily used in noisy environments, which demonstrate the necessity of path diversity for reliable WSANs. Our study also suggests that combining channel diversity with retransmission may effectively reduce the burstiness of transmission failures and judicious allocation of multiple transmissions in a shared slot can effectively improve network capacity without significantly impacting reliability

Joint source channel coding for progressive image transmission

Recent wavelet-based image compression algorithms achieve best ever performances with fully embedded bit streams. However, those embedded bit streams are very sensitive to channel noise and protections from channel coding are necessary. Typical error correcting capability of channel codes varies according to different channel conditions. Thus, separate design leads to performance degradation relative to what could be achieved through joint design. In joint source-channel coding schemes, the choice of source coding parameters may vary over time and channel conditions. In this research, we proposed a general approach for the evaluation of such joint source-channel coding scheme. Instead of using the average peak signal to noise ratio (PSNR) or distortion as the performance metric, we represent the system performance by its average error-free source coding rate, which is further shown to be an equivalent metric in the optimization problems. The transmissions of embedded image bit streams over memory channels and binary symmetric channels (BSCs) are investigated in this dissertation. Mathematical models were obtained in closed-form by error sequence analysis (ESA). Not surprisingly, models for BSCs are just special cases for those of memory channels. It is also discovered that existing techniques for performance evaluation on memory channels are special cases of this new approach. We further extend the idea to the unequal error protection (UEP) of embedded images sources in BSCs. The optimization problems are completely defined and solved. Compared to the equal error protection (EEP) schemes, about 0.3 dB performance gain is achieved by UEP for typical BSCs. For some memory channel conditions, the performance improvements can be up to 3 dB. Transmission of embedded image bit streams in channels with feedback are also investigated based on the model for memory channels. Compared to the best possible performance achieved on feed forward transmission, feedback leads to about 1.7 dB performance improvement

Energy-Efficient Distributed Estimation by Utilizing a Nonlinear Amplifier

abstract: Distributed estimation uses many inexpensive sensors to compose an accurate estimate of a given parameter. It is frequently implemented using wireless sensor networks. There have been several studies on optimizing power allocation in wireless sensor networks used for distributed estimation, the vast majority of which assume linear radio-frequency amplifiers. Linear amplifiers are inherently inefficient, so in this dissertation nonlinear amplifiers are examined to gain efficiency while operating distributed sensor networks. This research presents a method to boost efficiency by operating the amplifiers in the nonlinear region of operation. Operating amplifiers nonlinearly presents new challenges. First, nonlinear amplifier characteristics change across manufacturing process variation, temperature, operating voltage, and aging. Secondly, the equations conventionally used for estimators and performance expectations in linear amplify-and-forward systems fail. To compensate for the first challenge, predistortion is utilized not to linearize amplifiers but rather to force them to fit a common nonlinear limiting amplifier model close to the inherent amplifier performance. This minimizes the power impact and the training requirements for predistortion. Second, new estimators are required that account for transmitter nonlinearity. This research derives analytically and confirms via simulation new estimators and performance expectation equations for use in nonlinear distributed estimation. An additional complication when operating nonlinear amplifiers in a wireless environment is the influence of varied and potentially unknown channel gains. The impact of these varied gains and both measurement and channel noise sources on estimation performance are analyzed in this paper. Techniques for minimizing the estimate variance are developed. It is shown that optimizing transmitter power allocation to minimize estimate variance for the most-compressed parameter measurement is equivalent to the problem for linear sensors. Finally, a method for operating distributed estimation in a multipath environment is presented that is capable of developing robust estimates for a wide range of Rician K-factors. This dissertation demonstrates that implementing distributed estimation using nonlinear sensors can boost system efficiency and is compatible with existing techniques from the literature for boosting efficiency at the system level via sensor power allocation. Nonlinear transmitters work best when channel gains are known and channel noise and receiver noise levels are low.Dissertation/ThesisPh.D. Electrical Engineering 201

SCATTER PHY : an open source physical layer for the DARPA spectrum collaboration challenge

DARPA, the Defense Advanced Research Projects Agency from the United States, has started the Spectrum Collaboration Challenge with the aim to encourage research and development of coexistence and collaboration techniques of heterogeneous networks in the same wireless spectrum bands. Team SCATTER has been participating in the challenge since its beginning, back in 2016. SCATTER's open-source software defined physical layer (SCATTER PHY) has been developed as a standalone application, with the ability to communicate with higher layers through a set of well defined messages (created with Google's Protocol buffers) and that exchanged over a ZeroMQ bus. This approach allows upper layers to access it remotely or locally and change all parameters in real time through the control messages. SCATTER PHY runs on top of USRP based software defined radio devices (i.e., devices from Ettus or National Instruments) to send and receive wireless signals. It is a highly optimized and real-time configurable SDR based PHY layer that can be used for the research and development of novel intelligent spectrum sharing schemes and algorithms. The main objective of making SCATTER PHY available to the research and development community is to provide a solution that can be used out of the box to devise disruptive algorithms and techniques to optimize the sub-optimal use of the radio spectrum that exists today. This way, researchers and developers can mainly focus their attention on the development of smarter (i.e., intelligent algorithms and techniques) spectrum sharing approaches. Therefore, in this paper, we describe the design and main features of SCATTER PHY and showcase several experiments performed to assess the effectiveness and performance of the proposed PHY layer