Design of Low Power Data Preserving Flip Flop Using MTCMOS Technique

In order to reduce overall power consumption, a well-known technique is to scale supply voltages. However, to maintain performance, device threshold voltages must scale as well, which will cause sub threshold leakage currents to increase exponentially. The sub threshold voltage has to affect the two parameters one is the delay and other one is the sub threshold leakage current. Smaller the threshold voltage smaller will be delay while larger will be the sub threshold current. Controlling sub threshold leakage has been explored significantly in the literature, especially in the context of reducing leakage currents in burst mode type circuits, where the system spends the majority of the time in an idle standby, or sleep, state where no computation is taking place. MTCMOS or multi-threshold CMOS has been proposed as a very effective technique for reducing leakage currents during the standby by state by utilizing high sleep devices to gate the power supplies of a low logic block. Although MTCMOS circuit techniques are effective for controlling leakage currents in combinational logic, a drawback is that it can cause internal nodes to float, and cannot be directly used in standard memory cells without corrupting stored data. As a result, several researchers have explored possible MTCMOS latch designs that can reduce leakage currents yet maintain state during the standby modes. In this work a data preserving flip flop with reduced leakage power is designed using MTCMOS technique in 90nm technology with the help of CADENCE tool. The simulation results have shown that the leakage power is reduced by 25.70% compared to CMOS flip flop

A Power Gating Scheme for Ground Bounce Reduction during Mode Transition

Abstrac

LOW LEAKAGE CHARGE RECYCLING TECHNIQUE FOR POWER MINIMIZATION IN CNTFET CIRCUITS

Carbon Nanotube Field Effect Transistor (CNTFET) is one of the most promising candidates in the near future for digital design due to its better electrostatics and higher mobility characteristics. Parameters that determine the CNTFET performance are the number of tubes, pitch, diameter and oxide thickness. In this paper, a power gating design methodology to realise low power CNTFET digital circuits even under device parameter changes is presented. Investigation about the effect of different CNTFET parameters on dynamic and standby power is carried out. Simulation results reveal that the power gated circuits suppress a maximum of about 67% dynamic power and 59% standby power compared to conventional circuits

정적 램 및 파워 게이트 회로에 대한 전압 및 보존용 공간 할당 문제

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2021.8. 김태환.칩의 저전력 동작은 중요한 문제이며, 공정이 발전하면서 그 중요성은 점점 커지고 있다. 본 논문은 칩을 구성하는 정적 램(SRAM) 및 로직(logic) 각각에 대해서 저전력으로 동작시키는 방법론을 논한다. 우선, 본 논문에서는 칩을 문턱 전압 근처의 전압(NTV)에서 동작시키고자 할 때 모니터링 회로의 측정을 통해 칩 내의 모든 SRAM 블록에서 동작 실패가 발생하지 않는 최소 동작 전압을 추론하는 방법론을 제안한다. 칩을 NTV 영역에서 동작시키는 것은 에너지 효율성을 증대시킬 수 있는 매우 효과적인 방법 중 하나이지만 SRAM의 경우 동작 실패 때문에 동작 전압을 낮추기 어렵다. 하지만 칩마다 영향을 받는 공정 변이가 다르므로 최소 동작 전압은 칩마다 다르며, 모니터링을 통해 이를 추론해낼 수 있다면 칩별로 SRAM에 서로 다른 전압을 인가해 에너지 효율성을 높일 수 있다. 본 논문에서는 다음과 같은 과정을 통해 이 문제를 해결한다: (1) 디자인 인프라 설계 단계에서는 SRAM의 최소 동작 전압을 추론하고 칩 생산 단계에서는 SRAM 모니터의 측정을 통해 전압을 인가하는 방법론을 제안한다; (2) 칩의 SRAM 비트셀(bitcell)과 주변 회로를 포함한 SRAM 블록들의 공정 변이를 모니터링할 수 있는 SRAM 모니터와 SRAM 모니터에서 모니터링할 대상을 정의한다; (3) SRAM 모니터의 측정값을 이용해 같은 칩에 존재하는 모든 SRAM 블록에서 목표 신뢰수준 내에서 읽기, 쓰기, 및 접근 동작 실패가 발생하지 않는 최소 동작 전압을 추론한다. 벤치마크 회로의 실험 결과는 본 논문에서 제안한 방법을 따라 칩별로 SRAM 블록들의 최소 동작 전압을 다르게 인가할 경우, 기존 방법대로 모든 칩에 동일한 전압을 인가하는 것 대비 수율은 같은 수준으로 유지하면서 SRAM 비트셀 배열의 전력 소모를 감소시킬 수 있음을 보인다. 두 번째로, 본 논문에서는 파워 게이트 회로에서 기존의 보존용 공간 할당 방법들이 지니고 있는 문제를 해결하고 누설 전력 소모를 더 줄일 수 있는 방법론을 제안한다. 기존의 보존용 공간 할당 방법은 멀티플렉서 피드백 루프가 있는 모든 플립플롭에는 무조건 보존용 공간을 할당해야 해야 하기 때문에 다중 비트 보존용 공간의 장점을 충분히 살리지 못하는 문제가 있다. 본 논문에서는 다음과 같은 방법을 통해 보존용 공간을 최소화하는 문제를 해결한다: (1) 보존용 공간 할당 과정에서 멀티플렉서 피드백 루프를 무시할 수 있는 조건을 제시하고, (2) 해당 조건을 이용해 멀티플렉서 피드백 루프가 있는 플립플롭이 많이 존재하는 회로에서 보존용 공간을 최소화한다; (3) 추가로, 플립플롭에 이미 할당된 보존용 공간 중 일부를 제거할 수 있는 조건을 찾고, 이를 이용해 보존용 공간을 더 감소시킨다. 벤치마크 회로의 실험 결과는 본 논문에서 제안한 방법론이 기존의 보존용 공간 할당 방법론보다 더 적은 보존용 공간을 할당하며, 따라서 칩의 면적 및 전력 소모를 감소시킬 수 있음을 보인다.Low power operation of a chip is an important issue, and its importance is increasing as the process technology advances. This dissertation addresses the methodology of operating at low power for each of the SRAM and logic constituting the chip. Firstly, we propose a methodology to infer the minimum operating voltage at which SRAM failure does not occur in all SRAM blocks in the chip operating on near threshold voltage (NTV) regime through the measurement of a monitoring circuit. Operating the chip on NTV regime is one of the most effective ways to increase energy efficiency, but in case of SRAM, it is difficult to lower the operating voltage because of SRAM failure. However, since the process variation on each chip is different, the minimum operating voltage is also different for each chip. If it is possible to infer the minimum operating voltage of SRAM blocks of each chip through monitoring, energy efficiency can be increased by applying different voltage. In this dissertation, we propose a new methodology of resolving this problem. Specifically, (1) we propose to infer minimum operation voltage of SRAM in design infra development phase, and assign the voltage using measurement of SRAM monitor in silicon production phase; (2) we define a SRAM monitor and features to be monitored that can monitor process variation on SRAM blocks including SRAM bitcell and peripheral circuits; (3) we propose a new methodology of inferring minimum operating voltage of SRAM blocks in a chip that does not cause read, write, and access failures under a target confidence level. Through experiments with benchmark circuits, it is confirmed that applying different voltage to SRAM blocks in each chip that inferred by our proposed methodology can save overall power consumption of SRAM bitcell array compared to applying same voltage to SRAM blocks in all chips, while meeting the same yield target. Secondly, we propose a methodology to resolve the problem of the conventional retention storage allocation methods and thereby further reduce leakage power consumption of power gated circuit. Conventional retention storage allocation methods have problem of not fully utilizing the advantage of multi-bit retention storage because of the unavoidable allocation of retention storage on flip-flops with mux-feedback loop. In this dissertation, we propose a new methodology of breaking the bottleneck of minimizing the state retention storage. Specifically, (1) we find a condition that mux-feedback loop can be disregarded during the retention storage allocation; (2) utilizing the condition, we minimize the retention storage of circuits that contain many flip-flops with mux-feedback loop; (3) we find a condition to remove some of the retention storage already allocated to each of flip-flops and propose to further reduce the retention storage. Through experiments with benchmark circuits, it is confirmed that our proposed methodology allocates less retention storage compared to the state-of-the-art methods, occupying less cell area and consuming less power.1 Introduction 1 1.1 Low Voltage SRAM Monitoring Methodology 1 1.2 Retention Storage Allocation on Power Gated Circuit 5 1.3 Contributions of this Dissertation 8 2 SRAM On-Chip Monitoring Methodology for High Yield and Energy Efficient Memory Operation at Near Threshold Voltage 13 2.1 SRAM Failures 13 2.1.1 Read Failure 13 2.1.2 Write Failure 15 2.1.3 Access Failure 16 2.1.4 Hold Failure 16 2.2 SRAM On-chip Monitoring Methodology: Bitcell Variation 18 2.2.1 Overall Flow 18 2.2.2 SRAM Monitor and Monitoring Target 18 2.2.3 Vfail to Vddmin Inference 22 2.3 SRAM On-chip Monitoring Methodology: Peripheral Circuit IR Drop and Variation 29 2.3.1 Consideration of IR Drop 29 2.3.2 Consideration of Peripheral Circuit Variation 30 2.3.3 Vddmin Prediction including Access Failure Prohibition 33 2.4 Experimental Results 41 2.4.1 Vddmin Considering Read and Write Failures 42 2.4.2 Vddmin Considering Read/Write and Access Failures 45 2.4.3 Observation for Practical Use 45 3 Allocation of Always-On State Retention Storage for Power Gated Circuits - Steady State Driven Approach 49 3.1 Motivations and Analysis 49 3.1.1 Impact of Self-loop on Power Gating 49 3.1.2 Circuit Behavior Before Sleeping 52 3.1.3 Wakeup Latency vs. Retention Storage 54 3.2 Steady State Driven Retention Storage Allocation 56 3.2.1 Extracting Steady State Self-loop FFs 57 3.2.2 Allocating State Retention Storage 59 3.2.3 Designing and Optimizing Steady State Monitoring Logic 59 3.2.4 Analysis of the Impact of Steady State Monitoring Time on the Standby Power 63 3.3 Retention Storage Refinement Utilizing Steadiness 65 3.3.1 Extracting Flip-flops for Retention Storage Refinement 66 3.3.2 Designing State Monitoring Logic and Control Signals 68 3.4 Experimental Results 73 3.4.1 Comparison of State Retention Storage 75 3.4.2 Comparison of Power Consumption 79 3.4.3 Impact on Circuit Performance 82 3.4.4 Support for Immediate Power Gating 83 4 Conclusions 89 4.1 Chapter 2 89 4.2 Chapter 3 90박

Low energy digital circuits in advanced nanometer technologies

The demand for portable devices and the continuing trend towards the Internet ofThings (IoT) have made of energy consumption one of the main concerns in the industry and researchers. The most efficient way of reducing the energy consump-tion of digital circuits is decreasing the supply voltage (Vdd) since the dynamicenergy quadratically depends onVdd. Several works have shown that an optimumsupply voltage exists that minimizes the energy consumption of digital circuits. This optimum supply voltage is usually around 200 mV and 400 mV dependingon the circuit and technology used. To obtain these low supply voltages, on-chipdc-dc converters with high efficiency are needed.This thesis focuses on the study of subthreshold digital systems in advancednanometer technologies. These systems usually can be divided into a Power Man-agement Unit (PMU) and a digital circuit operating at the subthreshold regime.In particular, while considering the PMU, one of the key circuits is the dc-dcconverter. This block converts the voltage from the power source (battery, supercapacitor or wireless power transfer link) to a voltage between 200 mV and 400mV in order to power the digital circuit. In this thesis, we developed two chargerecycling techniques in order to improve the efficiency of switched capacitors dc-dcconverters. The first one is based on a technique used in adiabatic circuits calledstepwise charging. This technique was used in circuits and applications wherethe switching consumption of a big capacitance is very important. We analyzedthe possibility of using this technique in switched capacitor dc-dc converters withintegrated capacitors. We showed through measurements that a 29% reductionin the gate drive losses can be obtained with this technique. The second one isa simplification of stepwise charging which can be applied in some architecturesof switched capacitors dc-dc converters. We also fabricated and tested a dc-dcconverter with this technique and obtained a 25% energy reduction in the drivingof the switches that implement the converter.Furthermore, we studied the digital circuit working in the subthreshold regime,in particular, operating at the minimum energy point. We studied different modelsfor circuits working in these conditions and improved them by considering thedifferences between the NMOS and PMOS transistors. We obtained an optimumNMOS/PMOS leakage current imbalance that minimizes the total leakage energy per operation. This optimum depends on the architecture of the digital circuitand the input data. However, we also showed that important energy reductionscan be obtained by operating at a mean optimum imbalance. We proposed two techniques to achieve the optimum imbalance. We used aFully Depleted Silicon on Insulator (FD-SOI) 28 nm technology for most of the simulations, but we also show that these techniques can be applied in traditionalbulk CMOS technologies. The first one consists in using the back plane voltage of the transistors (or bulk voltage in traditional CMOS) to adjust independently theleakage current of the NMOS and PMOS transistor to work under the optimum NMOS/PMOS leakage current imbalance. We called this approach the OptimumBack Plane Biasing (OBB). A second technique consists of using the length of the transistors to adjust this leakage current imbalance. In the subthreshold regimeand in advanced nanometer technologies a moderate increase in the length has little impact in the output capacitance of the gates and thus in the dynamic energy.We called this approach an Asymmetric Length Biasing (ALB). Finally, we use these techniques in some basic circuits such as adders. We show that around 50% energy reduction can be obtained, in a wide range of frequency while working near the minimum energy point and using these techniques. The main contributions of this thesis are: • Analysis of the stepwise charging technique in small capacitances. •Implementation of stepwise charging technique as a charge recycling tech-nique for efficiency improvement in switched capacitor dc-dc converters. • Development of a charge sharing technique for efficiency improvement inswitched capacitor dc-dc converters. • Analysis of minimum operating voltage of digital circuits due to intrinsicnoise and the impact of technology scaling in this minimum. • Improvement in the modeling of the minimum energy point while considering NMOS and PMOS transistors difference. • Demonstration of the existence of an optimum leakage current imbalance be-tween the NMOS and PMOS transistors that minimizes energy consumptionin the subthreshold regiion. • Development of a back plane (bulk) voltage strategy for working in this optimum.• Development of a sizing strategy for working in the aforementioned optimum. • Analysis of the impact of architecture and input data on the optimum im-balance. The thesis is based on the publications [1–8]. During the Ph.D. program, other publications were generated [9–16] that are partially related with the thesis butwere not included in it.La constante demanda de dispositivos portables y los avances hacia la Internet de las Cosas han hecho del consumo de energía uno de los mayores desafíos y preocupación en la industria y la academia. La forma más eficiente de reducir el consumo de energía de los circuitos digitales es reduciendo su voltaje de alimentación ya que la energía dinámica depende de manera cuadrática con dicho voltaje. Varios trabajos demostraron que existe un voltaje de alimentación óptimo, que minimiza la energía consumida para realizar cierta operación en un circuito digital, llamado punto de mínima energía. Este óptimo voltaje se encuentra usualmente entre 200 mV y 400 mV dependiendo del circuito y de la tecnología utilizada. Para obtener estos voltajes de alimentación de la fuente de energía, se necesitan conversores dc-dc integrados con alta eficiencia. Esta tesis se concentra en el estudio de sistemas digitales trabajando en la región sub umbral diseñados en tecnologías nanométricas avanzadas (28 nm). Estos sistemas se pueden dividir usualmente en dos bloques, uno llamado bloque de manejo de potencia, y el segundo, el circuito digital operando en la region sub umbral. En particular, en lo que corresponde al bloque de manejo de potencia, el circuito más crítico es en general el conversor dc-dc. Este circuito convierte el voltaje de una batería (o super capacitor o enlace de transferencia inalámbrica de energía o unidad de cosechado de energía) en un voltaje entre 200 mV y 400 mV para alimentar el circuito digital en su voltaje óptimo. En esta tesis desarrollamos dos técnicas que, mediante el reciclado de carga, mejoran la eficiencia de los conversores dc-dc a capacitores conmutados. La primera es basada en una técnica utilizada en circuitos adiabáticos que se llama carga gradual o a pasos. Esta técnica se ha utilizado en circuitos y aplicaciones en donde el consumo por la carga y descarga de una capacidad grande es dominante. Nosotros analizamos la posibilidad de utilizar esta técnica en conversores dc-dc a capacitores conmutados con capacitores integrados. Se demostró a través de medidas que se puede reducir en un 29% el consumo debido al encendido y apagado de las llaves que implementan el conversor dc-dc. La segunda técnica, es una simplificación de la primera, la cual puede ser aplicada en ciertas arquitecturas de conversores dc-dc a capacitores conmutados. También se fabricó y midió un conversor con esta técnica y se obtuvo una reducción del 25% en la energía consumida por el manejo de las llaves del conversor. Por otro lado, estudiamos los circuitos digitales operando en la región sub umbral y en particular cerca del punto de mínima energía. Estudiamos diferentes modelos para circuitos operando en estas condiciones y los mejoramos considerando las diferencias entre los transistores NMOS y PMOS. Mediante este modelo demostramos que existe un óptimo en la relación entre las corrientes de fuga de ambos transistores que minimiza la energía de fuga consumida por operación. Este óptimo depende de la arquitectura del circuito digital y ademas de los datos de entrada del circuito. Sin embargo, demostramos que se puede reducir el consumo de manera considerable al operar en un óptimo promedio. Propusimos dos técnicas para alcanzar la relación óptima. Utilizamos una tecnología FD-SOI de 28nm para la mayoría de las simulaciones, pero también mostramos que estas técnicas pueden ser utilizadas en tecnologías bulk convencionales. La primer técnica, consiste en utilizar el voltaje de la puerta trasera (o sustrato en CMOS convencional) para ajustar de manera independiente las corrientes del NMOS y PMOS para que el circuito trabaje en el óptimo de la relación de corrientes. Esta técnica la llamamos polarización de voltaje de puerta trasera óptimo. La segunda técnica, consiste en utilizar los largos de los transistores para ajustar las corrientes de fugas de cada transistor y obtener la relación óptima. Trabajando en la región sub umbral y en tecnologías avanzadas, incrementar moderadamente el largo del transistor tiene poco impacto en la energía dinámica y es por eso que se puede utilizar. Finalmente, utilizamos estas técnicas en circuitos básicos como sumadores y mostramos que se puede obtener una reducción de la energía consumida de aproximadamente 50%, en un amplio rango de frecuencias, mientras estos circuitos trabajan cerca del punto de energía mínima. Las principales contribuciones de la tesis son: • Análisis de la técnica de carga gradual o a pasos en capacidades pequeñas. • Implementación de la técnica de carga gradual para la mejora de eficiencia de conversores dc-dc a capacitores conmutados. • Simplificación de la técnica de carga gradual para mejora de la eficiencia en algunas arquitecturas de conversores dc-dc de capacitores conmutados. • Análisis del mínimo voltaje de operación en circuitos digitales debido al ruido intrínseco del dispositivo y el impacto del escalado de las tecnologías en el mismo. • Mejoras en el modelado del punto de energía mínima de operación de un circuito digital en el cual se consideran las diferencias entre el transistor PMOS y NMOS. • Demostración de la existencia de un óptimo en la relación entre las corrientes de fuga entre el NMOS y PMOS que minimiza la energía de fugas consumida en la región sub umbral. • Desarrollo de una estrategia de polarización del voltaje de puerta trasera para que el circuito digital trabaje en el óptimo antes mencionado. • Desarrollo de una estrategia para el dimensionado de los transistores que componen las compuertas digitales que permite al circuito digital operar en el óptimo antes mencionado. • Análisis del impacto de la arquitectura del circuito y de los datos de entrada del mismo en el óptimo antes mencionado

Experimental and computational studies of calcium-triggered transmitter release

Calcium influx through presynaptic calcium channels triggers transmitter release, but many of the details that underlie calcium-triggered secretion are not well understood. In an attempt to increase our understanding of this process, synaptic transmission at the frog neuromuscular junction has been investigated using physiological experiments and computational modeling. Pharmacological manipulations ((R)-roscovitine and DAP) were used as tools to modulate presynaptic calcium influx and study effects on transmitter release. I showed that (R)-roscovitine predominately slowed deactivation kinetics of calcium current (by 427%), and as a result, increased the integral of calcium channel current evoked by a physiological action potential waveform (by 44%). (R)-roscovitine also increased the quantal content of acetylcholine released from the motor nerve terminals (by 149%) without changing paired-pulse facilitation under low calcium conditions. In contrast, exposure to 3,4-diaminopyridine (which affects transmitter release evoked by partially blocking potassium channels, altering the amplitude of the presynaptic action potential, and indirectly increasing calcium entry) increased paired-pulse facilitation (by 23%). In normal calcium conditions, both pharmacological treatments showed relatively similar effects on paired-pulse facilitation. I used a computational model, constrained by previous reports in the literature and my physiological measurements, to simulate my experimental data. This model faithfully reproduced calcium current with a single action potential, the average number of released synaptic vesicles, and the effects of (R)-roscovitine and DAP on calcium influx and vesicle release. Using this model, I made several predictions about the mechanisms underlying transmitter release. First, calcium ions originating from one or two voltage-gated calcium channels most often contributed to cause the fusion of each vesicle. Second, the calcium channel closest to a vesicle that fuses, provides 77% of calcium ions. My simulation of paired-pulse facilitation using the present model needed more adjustments, and in the process of adjusting the model parameters, various hypotheses that might explain observed short-term synaptic plasticity, including the effects of changes in buffer conditions, the effects of uneven calcium channel distribution, reducing terminal volume by adding vesicles to a storage pool, changes in the second action potential waveform, and possible persistent changes in vesicle release machinery were explored

A Charge-Recycling Scheme and Ultra Low Voltage Self-Startup Charge Pump for Highly Energy Efficient Mixed Signal Systems-On-A-Chip

The advent of battery operated sensor-based electronic systems has provided a pressing need to design energy-efficient, ultra-low power integrated circuits as a means to improve the battery lifetime. This dissertation describes a scheme to lower the power requirement of a digital circuit through the use of charge-recycling and dynamic supply-voltage scaling techniques. The novel charge-recycling scheme proposed in this research demonstrates the feasibility of operating digital circuits using the charge scavenged from the leakage and dynamic load currents inherent to digital design. The proposed scheme efficiently gathers the “ground-bound” charge into storage capacitor banks. This reclaimed charge is then subsequently recycled to power the source digital circuit. The charge-recycling methodology has been implemented on a 12-bit Gray-code counter operating at frequencies of less than 50 MHz. The circuit has been designed in a 90-nm process and measurement results reveal more than 41% reduction in the average energy consumption of the counter. The total energy savings including the power consumed for the generation of control signals aggregates to an average of 23%. The proposed methodology can be applied to an existing digital path without any design change to the circuit but with only small loss to the performance. Potential applications of this scheme are described, specifically in wide-temperature dynamic power reduction and as a source for energy harvesters. The second part of this dissertation deals with the design and development of a self-starting, ultra-low voltage, switched-capacitor (SC) DC-DC converter that is essential to an energy harvesting system. The proposed charge-pump based SC-converter operates from 125-mV input and thus enables battery-less operation in ultra-low voltage energy harvesters. The charge pump does not require any external components or expensive post-fabrication processing to enable low-voltage operation. This design has been implemented in a 130-nm CMOS process. While the proposed charge pump provides significant efficiency enhancement in energy harvesters, it can also be incorporated within charge recycling systems to facilitate adaptable charge-recycling levels. In total, this dissertation provides key components needed for highly energy-efficient mixed signal systems-on-a-chip